Summary of Contents for Pentair Pool Products Pressure Side Pool Cleaner Legend II
Page 1
® Pressure Side Pool Cleaner Installation Guide IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS SAVE THESE INSTRUCTIONS LEGEND® II INSTALLATION MANUAL...
Page 2
10951 West Los Angeles Ave., Moorpark, CA 93021 • (800) 831-7133 • (805) 553-5000 Trademarks and Disclaimers. Pentair Water Pool and Spa and Legend are trademarks and/or registered trademarks of Pentair Water Pool and Spa, Inc. Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products.
Page 3
Important Information: ® The Legend II automatic pool cleaner comes ready to connect into a female threaded 1-1/2" dedicated return line. Other connections are possible, but they require additional fittings. For more information, please contact our Technical Support Department at 1-800-831-7133. Also, if you have a chlorinator, solar system or other air inducing equipment, please contact our Technical Support Department before you install the Legend ®...
I. Introduction ... 1 A. Thank You for Choosing the Legend B. What to Expect from the Legend II. Installation Instructions ... 2 ® A. Legend II Components ... 2 B. Pool Connections ... 2 C. Installing the Twist Lock Pressure Relief Valve (Wall Fitting) ... 2 D.
I. Introduction A. Thank You for Choosing the ® Legend II Pool Cleaner Congratulations on the purchase of your new automatic pool cleaner. The Legend to give you years of dependable and efficient service. ® With the Legend II, you and your family will spend more time relaxing and enjoying your pool and less time cleaning it.
II. Installation Instructions A. Legend ® II Components ® The Legend II Box Contains: 1. Cleaner Head 2. Sand & Silt Bag 3. Sweep Hose 4. Complete Feed Hose a. 1 - 18 in. hose b. 1 - 2 ft. hose c.
D. Pressure Testing Instructions 1. Make sure the pool filter is clean before conducting this pressure test. 2. Twist lock the Wall Fitting with Feeder Hose into the Wall Adapter. 3. Have someone hold the Pressure Tester end of the Feed Hose beneath the water while you turn on the pool pump.
F. Hooking up the Legend 1. Remove the Pressure Tester from the free end of the Feeder Hose by unscrewing the Hose Nut. Left hand thread (reverse), (see illustration previous page). 2. Place mender nut on Legend Connect the open end of the Feed Hose to the ®...
H. Fine Tuning the Legend 1. Thrust Jet Adjustment There are two Thrust Jets located in the back of the ® Legend II. These Thrust Jets alter the direction of the cleaner. The factory standard position for the jets is set slightly to the right. (See illustration below.) In certain pools, altering the thrust jets can increase performance of the Legend ®...
Page 10
Legend Professional Pool Dealer. ® II, call your If you have any additional questions, please contact Pentair Water Pool and Spa, Inc., Technical Support Department at: 1-800-831-7133, Monday through Friday. LEGEND® II INSTALLATION MANUAL...
III. Operation/Periodic Maintenance A. Connecting/Disconnecting the ® Legend Turn off pool pump. Then take the Wall Fitting and twist lock the Wall Fitting clockwise into the Wall Adapter. To disconnect the Legend twist counter clockwise. The Wall Adapter should remain in the pool wall. B.
You need to rotate or replace the tires when edges become rounded. The Wheel Bearings are warranted free of defects when shipped from Pentair Water Pool and Spa, Inc., and are considered a wear item. A good bearing will spin freely.
III. Operation/Periodic Maintenance - (cont.) F. Storage and Winterizing ® Never leave or store the Legend II in direct sunlight. ® When storing the Legend II for the winter, be sure to drain all the water from it. This is important since freeze damage is not covered under the warranty.
IV. TROUBLESHOOTING AND PERFORMANCE TIPS To insure the best performance from your cleaner, follow the troubleshooting guide listed below. A. PROBLEMS & SOLUTIONS ® Problem: Legend II doesn't move or moves sluggishly or hangs up on steps. Solution: 1. Be sure filter and filter pump are on and working properly.
Page 15
IV. TROUBLESHOOTING AND PERFORMANCE TIPS A. PROBLEMS & SOLUTIONS - (cont.) Problem: Sweep Hose is sucked into the cleaner. Solution: 1. Adjust the Sweep Hose using the Adjustment Screw located on the bottom of the Swivel Mast. Turn Adjustment Screw clockwise until the Sweep Hose is in a gentle sweeping motion.
Page 16
TIPS FOR CUTTING HOSE IN A SMALL POOL, AND FOR ADDING HOSES FOR LARGE POOLS 1. Tips on Hose Cutting for Larger Pools. If the hose is short of the farthest end of the pool, add an additional section of hose (Part # LX17), one Swivel (Part # LX19), two Mender Nuts w/O-Rings (Part # LX20), and one Hose Float (Part # LXD10).