Serial Port Settings - Sony SNT-V304 User Manual

Settings

Serial Port Settings

The (COM1 and COM2) icons represent the
serial ports of the video network station. Use these
icons when an EVI-D100/D100P/D30/D31/G20/G21
or HSR-1/1P/2/2P is connected to the "COM1" or
"COM2" ports to set up serial port function and
communications parameters.
Note
If a serial port has the Click "Save" icon enabled, the
video network station reboots and alarm memory
contents are erased, so check the alarm memory
contents, if necessary, before setting.
1
Click the "COM1" (or "COM2") icon.
The screen displays the "Serial Port 1 Settings" (or
"Serial Port 2 Settings").
2
Make the required settings. Available settings are
as follows.
Setting Options
Purpose Pan Tilt
HSR (only
displayed for
COM1)
20
Description
Select this if an EVI-D100/
D100P/D30/D31/G20/G21 is
connected to the port.
When selected, the "Pan Tilt"
icon shown below is added
next to the "COM1" or
"COM2" icon.
Select this if an HSR-1/1P/2/
2P is connected to the port.
When selected, the "HSR"
icon shown below is added
next to the "COM1" icon.
Setting Options
Purpose Modem
(only
displayed for
COM2)
Generic
None
Serial Select the appropriate interface type:
Mode [RS232] for the EVI-D100/D100P/D30/D31/
(only
G20/G21 and HSR-1/1P/2/2P.
displayed
for
COM1)
Baud Select the transfer speed: Select [9600]
Rate when the device supports EVI-D100/
(bps)
D100P/D30/D31/G20/G21 or Kalatel
protocol, or [9600] to [38400] as the HSR
setting to match that of the HSR-1/1P/2/2P.
Data Bits Select [8] data bits when the device
(length) supports EVI-D100/D100P/D30/D31/G20/
G21, HSR-1/1P/2/2P, or Kalatel protocol.
Stop Bits Select [1] stop bit when the device supports
EVI-D100/D100P/D30/D31/G20/G21, HSR-
1/1P/2/2P, or Kalatel protocol.
Parity Bit Select [None] when the device supports
EVI-D100/D100P/D30/D31/G20/G21, HSR-
1/1P/2/2P, or Kalatel protocol.
z Hint
Only an HSR-1/1P/2/2P or a modem can be
connected to the video network station at any given
time. Accordingly, when [COM1] is set to [HSR]
or [COM2] set to [Modem], the other option button
is not displayed.
3
Click the "Save" icon when finished with the
settings.
The new settings are saved, the video network
station reboots, and the display changes as follows
depending on the selected usage.
• When [Pan Tilt] is selected, the "Pan Tilt
Settings" page appears. Refer to "Pan/Tilt Driver
and Video Camera ID Setup" below.
• When [HSR] is selected, the "Sony HSR
Settings" page appears. Refer to "HSR-1/1P/2/2P
Setup" on page 23.
Description
Select this if a modem is
connected to the port.
When selected, the "Modem"
and "ISP" icons shown below
are displayed.
Select if using a CGI/Generic
driver.
When selected, the following
"Generic" icon is added next
to the "COM1" or "COM2"
icon.
Select this if no device is
connected to a port.