Page 1
Prowler ™ Robotic Inground Pool Cleaners Installation User's Guide IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS SAVE THESE INSTRUCTIONS...
Page 2
Trademarks and Disclaimers: Prowler and the Pentair Water Pool and Spa logo are trademarka of Pentair Water Pool and Spa, Inc. Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Pentair Water Pool and Spa, Inc.
The Prowler ™ 720 and 730 pool cleaners are designed and manufactured to provide many years of safe and reliable service when installed, operated and maintained according to the information in this manual. Throughout the manual, safety warnings and cautions are identified by the “...
720 and 730 Overview Vacuums what you can see, filters what you can’t... Prowler 720 and 730 are the computer-controlled, programmed cleaners that scrub and vacuum your pool’s ™ bottom, walls and steps and provides supplemental filtration of pool water.
Cleans any size, shape and type of standard residential pool in only one hour. • The intelligent program enables the cleaner to fully cover and efficiently clean any standard residential swimming pool in approximately one hour (90 minutes for larger residential pools). Prowler 720 and 730 Installation and User’s Guide ™...
Cleaner ™ cleaner to clean your pool. We hope that you will enjoy using your new Photo shows the Prowler™ 720 in a convenient, protective cradle for easy storage and transport, also available for the Prowler™ 730 model. Section 2 Installation 720 and 730 robotic pool cleaners.
NOTE: When the Power Supply is turned off, the Mode is automatically returned to the "Standard Mode" (floor cleaning only). CAUTION — Be sure to always keep your Pentair pool cleaner properly stored anywhere between 50° to 104° Fahrenheit, (10° to 40° Celsius). This will keep the motors, plastics and seals protected. Failure to comply will result in loss of warranty.
4. Push the cover downwards into the 2 slots (Step 4). 5. Push the top of the cover towards the battery until it snaps into place (Step 5). 6. Put the screw back into place. Figure 13. Prowler 720 and 730 Installation and User’s Guide ™...
6. Re-install the bottom lid assembly onto the body. Push down on it until all (4) locking tabs snap properly into place. ™ 720 and 730 Cleaner Lock Tabs Figure 14. Section 3 Maintenance Label Prowler ™ 720 and 730 Installation and User’s Guide...
4. Place the new PVA brush onto the hexagonal tube and replace the end hub. 5. Re-install the wheel tube in place and reattach the side plate by screwing back- in the four screws. Prowler 720 and 730 Installation and User’s Guide ™ 9, Figure 14, Steps 1-4. Figure 15.
Prowler™ cleaner. Completely untangle and then properly coil the Floating Cable. Your Prowler™ cleaner and Power Supply should be stored in a dry, protected area away from freezing temperatures. E-Z SWIVEL - Location Handle Cover Core Cable Assy. Figure 19. Prowler ™ 720 and 730 Installation and User’s Guide patent pending...
SHRINK TUBE - 1 METER P12124 SHRINK TUBE - 1 METER P12125 BUTT CONNECTOR SWIVEL SOCKET Used on both of the Prowler ™ 720 Model DESCRIPTION ™ 720 & 730 models. Prowler ™ 720 and 730 Installation and User’s Guide...
POWER SUPPLY ASSY. 1 HR. POWER SUPPLY CORD BODY ASSY. - INCLUDES P/N P12115 SHRINK TUBE 1 METER SWIVEL REMOTE CONTROL AXLE FOR WHEEL TUBE ASSY. SOCKET ™ 720 & 730 models. Prowler ™ 720 and 730 Installation and User’s Guide...
Page 20
Notes Prowler 720 and 730 Installation and User’s Guide ™...
Page 21
Notes Prowler ™ 720 and 730 Installation and User’s Guide...
Page 22
Notes Prowler 720 and 730 Installation and User’s Guide ™...