Removing And Replacing; Refrigerator Doors - Kenmore 111.7304 Use & Care Manual

Mfl63264288
Table of Contents

Advertisement

en-us
Aligning the appliance
NOTICE
To ensure that the appliance
operates correctly, use a level to
align the appliance.

REMOVING AND REPLACING

If the appliance is not level, water
If the refrigerator doors are not

REFRIGERATOR DOORS

may flow out of the ice maker, ice
properly aligned:
cubes may be irregular, or the doors
may not close properly.
WARNING
1. Place the appliance in the
designated location.
Risk of electric shock!
Risk of electric shock!
Before removing the top panel:
Before removing top hinge cover
1. Shut off the water supply to the
• Shut off the water supply to the appliance.
appliance.
• Unplug the appliance or switch off power from the
2. Unplug the appliance or switch
off the fuse.
breaker or fuse panel.
1. Determine which refrigerator door
needs adjustment.
To remove the left refrigerator door:
2. Remove the five screws on the top
1. Remove top hinge cover using a phillips type
panel.
2. Remove the three screws from the
screwdriver by removing 5 screws
3. Raise the panel.
base panel.
3. Remove the base panel.
4. Loosen the screw.
2. Remove the grounding wire (green with yellow stripe)
Do not remove the screw!
by removing the screw using a phillips screwdriver, and
disconnect the harness wires and water tube.
4. Use a hexagonal wrench to loosen
the two front feet until they are
firmly planted on the floor and then
align the front of the appliance.
5. Move the hinge sideways to adjust
3. Using a large phillips screwdriver, turn top hinge
the refrigerator door.
fastener counterclockwise to remove the top hinge/
6. Tighten the screw.
plate.
7. Realign panel.
CAUTION: After the hinge is removed, the door can
8. Insert and tighten the five screws.
fall down forward. Please secure door during this
process.
8
F706-4(영)(Kenmore)_신포맷.indd 14
REFRIGERATOR INSTALLATION
Adjusting the freezer
compartment drawer
1. Determine which side needs
WARNING
adjustment.
2. Loosen the two screws.
Do not remove the screws!
5. Use a hexagonal wrench to turn
the screws and then align the rear
of the appliance.
To raise the rear of the appliance:
Turn the screw clockwise.
To lower the rear of the appliance:
Turn the screw counterclockwise.
3. Use the top screw to adjust the
freezer compartment drawer.
4. Tighten the two screws.
Installing the handles
Do not install the handles until the
appliance is installed in its designated
location and is level.
All handles are the same and are
installed in the same manner.
6. Use the level to check if the
1. Remove the protective films from
appliance is level.
the refrigerator doors and the
freezer compartment drawer.
NOTICE
To ensure that the appliance does
not move, the front feet must be
firmly planted on the floor.
7. If the height of the refrigerator
compartment doors are uneven or
if the freezer compartment drawer
is slanted after adjusting the level
of the appliance, use the following
method to adjust them.
Adjusting a refrigerator door
If the height of the refrigerator doors
is uneven:
1. Determine which refrigerator door
needs to be raised.
2. Turn the screw nut on the lower
hinge to adjust the refrigerator
4. Lift the door from the middle hinge pin and remove
door.
the door. Place the door, inside facing up, on a non-
2. Insert the door handles into the
To raise a refrigerator door:
scratch surface.
guides.
Turn the screw counterclockwise.
� Refrigerator doors: The handle
If the refrigerator doors are not
screws must face the center of
properly aligned:
the appliance.
� Freezer compartment drawer:
WARNING
The handle screws must face
down.
Risk of electric shock!
Before removing the top panel:
1. Shut off the water supply to the
appliance.
2. Unplug the appliance or switch
off the fuse.
To lower a refrigerator door:
Turn the screw clockwise.
1. Determine which refrigerator door
needs adjustment.
To remove the right refrigerator door:
2. Remove the five screws on the top
1. Remove top hinge cover using a phillips type
panel.
screwdriver by removing 5 screws.
3. Raise the panel.
3. Tighten the handle screws with the
accompanying Allen wrench.
4. Loosen the screw.
2. Using a large phillips screwdriver, turn top hinge
Do not remove the screw!
fastener counterclockwise to remove the top hinge/
plate.
CAUTION: After the hinge is removed, the door can
fall down forward. Please secure door during this
process.
Installing the base plate
1. Remove the three screws on the
appliance.
2. Mount the base plate.
3. Insert the three screws and
tighten.
5. Move the hinge sideways to adjust
the refrigerator door.
6. Tighten the screw.
7. Realign panel.
3. Lift the door from the middle hinge pin and remove
the door. Place the door, inside facing up, on a non-
8. Insert and tighten the five screws.
scratch surface.
14
en-us
Adjusting the freezer
compartment drawer
1. Determine which side needs
adjustment.
2. Loosen the two screws.
Do not remove the screws!
3. Use the top screw to adjust the
freezer compartment drawer.
4. Tighten the two screws.
Installing the handles
Do not install the handles until the
appliance is installed in its designa
location and is level.
All handles are the same and are
installed in the same manner.
1. Remove the protective films fro
the refrigerator doors and the
freezer compartment drawer.
9
2016-08-29 오후 3:36:41

Hide quick links:

Advertisement

Table of Contents
loading

Table of Contents