GE C30 Instruction Manual page 175

Ur series
Hide thumbs Also See for C30:
Table of Contents

Advertisement

5 SETTINGS
It can also be programmed to reset automatically through the
tings. These settings enable the autoreset timer and specify the associated time delay. The autoreset timer can be
used in select-before-operate (SBO) breaker control applications, where the command type (close/open) or breaker
location (feeder number) must be selected prior to command execution. The selection must reset automatically if con-
trol is not executed within a specified time period.
Self-reset mode: In self-reset mode, a pushbutton will remain active for the time it is pressed (the pulse duration) plus
the dropout time specified in the
pulse duration is specified by the
setting has no effect on the pulse duration.
BTN 1 SET
The pushbutton is reset (deactivated) in self-reset mode when the dropout delay specified in the
setting expires.
TIME
The pulse duration of the remote set, remote reset, or local pushbutton must be at least 50 ms to operate the push-
button. This allows the user-programmable pushbuttons to properly operate during power cycling events and vari-
ous system disturbances that may cause transient assertion of the operating signals.
NOTE
The local and remote operation of each user-programmable pushbutton can be inhibited through the
settings, respectively. If local locking is applied, the pushbutton will ignore set and reset commands
PUSHBTN 1 REMOTE
executed through the front panel pushbuttons. If remote locking is applied, the pushbutton will ignore set and reset com-
mands executed through FlexLogic™ operands.
The locking functions are not applied to the autoreset feature. In this case, the inhibit function can be used in SBO control
operations to prevent the pushbutton function from being activated and ensuring "one-at-a-time" select operation.
The locking functions can also be used to prevent the accidental pressing of the front panel pushbuttons. The separate
inhibit of the local and remote operation simplifies the implementation of local/remote control supervision.
Pushbutton states can be logged by the event recorder and displayed as target messages. In latched mode, user-defined
messages can also be associated with each pushbutton and displayed when the pushbutton is on or changing to off.
PUSHBUTTON 1 FUNCTION: This setting selects the characteristic of the pushbutton. If set to "Disabled", the push-
button is not active and the corresponding FlexLogic™ operands (both "On" and "Off") are de-asserted. If set to "Self-
Reset", the control logic is activated by the pulse (longer than 100 ms) issued when the pushbutton is being physically
pressed or virtually pressed via a FlexLogic™ operand assigned to the
When in "Self-Reset" mode and activated locally, the pushbutton control logic asserts the "On" corresponding Flex-
Logic™ operand as long as the pushbutton is being physically pressed, and after being released the deactivation of
the operand is delayed by the drop out timer. The "Off" operand is asserted when the pushbutton element is deacti-
vated. If the pushbutton is activated remotely, the control logic of the pushbutton asserts the corresponding "On" Flex-
Logic™ operand only for the time period specified by the
If set to "Latched", the control logic alternates the state of the corresponding FlexLogic™ operand between "On" and
"Off" on each button press or by virtually activating the pushbutton (assigning set and reset operands). When in the
"Latched" mode, the states of the FlexLogic™ operands are stored in a non-volatile memory. Should the power supply
be lost, the correct state of the pushbutton is retained upon subsequent power up of the relay.
PUSHBTN 1 ID TEXT: This setting specifies the top 20-character line of the user-programmable message and is
intended to provide ID information of the pushbutton. Refer to the User-definable displays section for instructions on
how to enter alphanumeric characters from the keypad.
PUSHBTN 1 ON TEXT: This setting specifies the bottom 20-character line of the user-programmable message and is
displayed when the pushbutton is in the "on" position. Refer to the User-definable displays section for instructions on
entering alphanumeric characters from the keypad.
PUSHBTN 1 OFF TEXT: This setting specifies the bottom 20-character line of the user-programmable message and is
displayed when the pushbutton is activated from the on to the off position and the
"Latched". This message is not displayed when the
status is implied to be "Off" upon its release. The length of the "Off" message is configured with the

DISPLAY PROPERTIES
PUSHBTN 1 HOLD: This setting specifies the time required for a pushbutton to be pressed before it is deemed active.
This timer is reset upon release of the pushbutton. Note that any pushbutton operation will require the pushbutton to be
pressed a minimum of 50 ms. This minimum time is required prior to activating the pushbutton hold timer.
GE Multilin
PUSHBTN 1 DROP-OUT TIME
PUSHBTN 1 DROP-OUT TIME
PUSHBUTTON 1 FUNCTION
setting.
FLASH MESSAGE TIME
C30 Controller System
and
PUSHBTN 1 AUTORST
setting. If the pushbutton is activated via FlexLogic™, the
only. The time the operand remains assigned to the
PUSHBTN 1 SET
setting.
PUSHBTN 1 DROP-OUT TIME
is "Self-reset" as the pushbutton operand
5.2 PRODUCT SETUP
set-
PUSHBTN 1 AUTORST DELAY
PUSH-
PUSHBTN 1 DROP-OUT
and
PUSHBTN 1 LOCAL
setting.
PUSHBUTTON 1 FUNCTION
PRODUCT SETUP
5-49
5
is

Advertisement

Table of Contents
loading

Table of Contents