Table of Contents
Advertisement
Service Conditions (cont'd)
7.
If Serial Call is not set to the incoming trunk, the caller is not connected to the announcement
when the conversation with the first party ends (after being placed on Consultation Hold), but
receives Reorder Tone.
8.
This service is available to the incoming route where AUTOMATED ATTENDANT [A-82] or
REMOTE ACCESS TO SYSTEM [R-2] are set.
9.
When the registers are all busy when Serial Call is attempted, the caller receives Reorder Tone.
10. Whether to send the announcement can be determined on a system basis. If the announcement
is not sent, the caller receives Dial Tone. Both the first and the second announcement is
connected in single connection, and the caller receives no tone until the announcement is sent.
11. When Serial Call is attempted, and the caller encounters all announcement trunks busy or when
there is no announcement trunk, the caller receives Dial Tone.
12. The caller can dial the desired station/trunk number during the announcement.
13. This service is provided only when the caller uses the DTMF telephone.
14. The caller is connected to the announcement when the caller is engaged in a two party
connection with the station, central office line, tie line, or the Attendant and then the station,
central office line, tie line or the Attendant releases.
15. If the caller does not dial any number after the announcement, the caller receives no tone until
the register prepause timer expires.
16. In case the register prepause timer expires after the announcement, whether to recall to the
term
operator D
17. When recalling to the D
data. However, in case the central office trunk works with Loop Start system (route data LSG=0),
release cannot be detected; therefore, when recall to the D
setting is ended, the D
18. Recall to the D
according to the ringer pattern 5 ASYD sys data 3 INDEX 7.
a.) In case the D
term
D
is called. If the set line is accommodated in the other D
term
D
becomes busy status (lights in red) and CALL FORWARDING – ALL CALLS [C-5]
and FORWARDING – DON'T ANSWER [C-3] is not available. When the set line is the
my line of the D
term
D
user)
b.) In case the D
selected by the same transaction as ordinary serial calling. Therefore, CALL
FORWARDING – ALL CALLS [C-5], CALL FORWARDING – BUSY LINE [C-2] and
STATION HUNTING – CIRCULAR [S-7] are available, and the LCD on the D
is selected as a Prime Line indicates "RECALL".
CALL FORWARDING – DON'T ANSWER [C-3] is not available. In case to end the setting
is selected at item 18, the central office line/tie line is released. (ROT is sent out.); in case
to continue is selected, dialing of the next number is allowed. (DT is sent out.)
19. Conditions for restriction are as follows.
a.) when the dead number or the dead level is dialed (if the dead number announcement
data is assigned, this announcement has priority.)
b.) in case of inter digit timer timeout while the station number is dialed.
c.) when the called station does not answer for 30 seconds (if CALL FORWARDING -
DON'T ANSWER [C-3] is set, the call is forwarded.)
NEAX2400 ICS Business Features and Specifications
NDA-24143, Issue 4
Serial Call - D
user or to release the call automatically can be selected on a system basis.
term
, whether to end or continue this setting can be selected by system
term
user can press the "SERIAL CALL" key again and reset.
term
selected at item 17 is activated with the following steps and ringing is
term
setting SERIAL CALL is free, the destination is the set line and only the
term
, the LCD displays "RECALL". (Ordinary transaction for recall to the
term
setting SERIAL CALL is busy, another free line among the D
term
term
, this setting is ended. If this
S-127
term
multi-line, the other
term
s is
term
which
Page 501
Advertisement
Table of Contents
