Specifications - Makita 2704 Instruction Manual

ENGLISH (Original instructions)
1-1. Hole diameter 8 mm
2-1. 6 mm Std. washer
2-2. No.10 wood screw 40 mm min.
length
3-1. 6 mm Std. washer
3-2. 6 mm Mounting bolt & Nut tighten
securely
4-1. Miter gauge
5-1. Rip fence
5-2. Push stick
6-1. Handle
7-1. Lock lever
7-2. Arrow pointer
7-3. Handwheel
8-1. 90 ﾟ Adjusting screw
8-2. 45 ﾟ Adjusting screw
10-1. Arrow pointer
11-1. Switch
12-1. Padlock
13-1. Switch
14-1. Lever
15-1. Sub table (R)
16-1. Scale plate
16-2. Screw
17-1. Sub table (back)
17-2. Screw
18-1. Screw
18-2. Sub table (L)
19-1. Offset wrench
19-2. Hex nut
19-3. Wrench
20-1. Inner flange
20-2. Ring

SPECIFICATIONS

Model
Arbor hole
Blade diameter
Max. cutting
capacities
No load speed (min
Table size (L x W)
Dimensions (L x W x H) with table(s) not
extended
Net weight
Safety class
• Due to our continuing programme of research and development, the specifications herein are subject to change without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Explanation of general view
20-3. Saw blade
20-4. Outer flange
20-5. Hex nut
21-1. Offset wrench
21-2. Wrench
22-1. Blade guard
22-2. Riving knife
22-3. blade guard mounting portion
(stay)
23-1. Blade guard
23-2. Riving knife
24-1. Riving knife
24-2. Blade guard
24-3. Lever
25-1. Blade guard
25-2. Riving knife
26-1. Blade
26-2. These two clearances should be
equal.
26-3. Riving knife
26-4. Hex bolts (B)
26-5. Hex bolts (A)
27-1. Riving knife
27-2. Blade guard
28-1. Hook
28-2. Knob
28-3. Guide rail
29-1. Scale
30-1. Hex bolts
32-1. Rip fence
32-2. Released position
32-3. Moving position
32-4. Lock position
(for European countries)
90°
45°
-1
)
(665 mm - 1,045 mm) x (753 mm - 1,066 mm)
with sub tables (R) and (back)
715 mm x 753 mm x 344 mm
with sub tables (R) and (back)
2704
30 mm
260 mm
93 mm
64 mm
4,800
34.9 kg
6
33-1. Rip fence
33-2. Moving position
33-3. Screw (B)
33-4. Screw (A)
34-1. Guideline
34-2. Screws
36-1. Face/edge parallel
36-2. Handle
36-3. Wood screw
36-4. Glue together
37-1. Face/edge parallel
38-1. No. 10 wood screws (long enough
to penetrate halfway into facing)
41-1. Push stick
42-1. Auxiliary fence
43-1. Push block
43-2. Auxiliary fence
44-1. CROSS CUTTING
44-2. MITERING
44-3. BEVEL CUTTING
44-4. COMPOUND MITERING
(ANGLES)
45-1. Knob
45-2. Small plate
45-3. Screw for positive stop
46-1. Groove
46-2. Miter gauge
46-3. Knob
49-1. Limit mark
50-1. Brush holder cap
50-2. Screwdriver
(for other than European countries)
25 mm and 25.4 mm
255 mm
91 mm
63 mm
567 mm x (753 mm - 1,066 mm)
with sub table (R)
665 mm x 753 mm x 344 mm
with sub table (R)
29.5 kg
./II