Page 2
Each product and program carries a respective written warranty, the only warranty on which the customer can rely. Paxar reserves the right to make changes in the product, the programs, and their availability at any time and without notice. Although Paxar has...
Page 3
Operation in Italy requires a user license. Trademarks Paxar is a trademark of Paxar Corporation. Monarch is a registered trademark of Paxar Americas, Inc. 9430R and Paxar Monarch Sierra Sport are trademarks of Paxar Americas, Inc. Paxar Americas, Inc. 170 Monarch Lane...
TA B L E O F C O N T E N T S GETTING STARTED ... 1-1 Unpacking the Printer ... 1-1 Programming Information ... 1-1 Duty Cycle ... 1-1 Battery and Safety Information ... 1-2 Installing the Battery ... 1-3 Charging the Battery ...
D u t y C y c l e The 9430R printer is designed to print up to 1000 inches per day. The average print rate is 1 inch every 10 seconds at a text character print density of 25% (i.e., one character printed out of every four positions).
B a t t e r y a n d S a f e t y I n f o r m a t i o n The printer is powered by a 6.0V Nickel Metal Hydride (NiMH) battery. Charging time in the printer is approximately 1.5 hours.
I n s t a l l i n g t h e B a t t e r y One battery may be included with the printer. The printer’s battery must be charged before using it. 1. Unlock the battery door by sliding down the tabs using your thumbs.
C h a r g i n g t h e B a t t e r y The printer’s battery must be charged before using it. The battery can be charged using the single or four-station charger. See Appendix A, “Specifications” for part numbers.
Red or Orange Amber Green Status The printer has an error and is not ready to accept data. The battery is charging at a fast rate. If the battery voltage is below 5.0V, the battery is “trickle” charged until the battery reaches 5.0V.
Hardware Reset Enable Reset Disable Reset Printer Power Continuous Power On** Auto Power Off * Switch 7 is not used. ** The printer stays on all the time - pressing the power (P) button has no effect. 1-6 Getting Started...
A t t a c h i n g t h e B e l t C l i p 1. The printer comes with a belt clip. 2. Turn the printer over. 3. Attach the belt clip as shown. Insert the printer’s round knob into the latch and pull up until it “clicks” into place.
L O A D I N G S U P P L I E S The printer can print text, bar codes, and some limited graphics on thermal direct receipt paper. See Appendix A, “Specifications” for the width and thickness requirements.
7. Turn on the printer. T e a r i n g S u p p l y The printer’s supply door acts as a tear bar. Tear down against the tear bar to remove receipts. NOTE: Do not tear supply up against the printhead or sideways, because the supply door may open.
U s i n g D i f f e r e n t S i z e S u p p l y R o l l s The printer can use one, two, or three-inch wide supply rolls. However, you need to order the supply guide adapter if you are using one or two-inch wide supply.
1. Connect the communication cable. See “Connecting the Printer” in Chapter 1. 2. Turn on the printer. 3. Send a data stream to the printer. Refer to the Programmer’s Manual 4. Remove the printed receipts. U s i n g t h e M a g n e t i c S t r i p e R e a d e r Read the following if your printer has the optional magnetic stripe reader, which is factory installed.
Page 20
The magnetic stripe must be facing toward the supply door while it is passed through the reader. Stripe is facing toward supply door. The green/orange LED on the printer indicates the following: LED Indicator Green Red or...
Do not use sharp objects to clean the printhead. This may damage the printer and require a service charge. 1. Turn off the printer. 2. Lift up the “T” lever on the supply door and wrap your fingers around it.
Page 22
Rub the cotton swab across the tear bar to remove any build-up. 9. Use a can of compressed air to remove any debris from the supply well. 10. Reload the supply roll. 11. Turn on the printer. 4-2 Cleaning Tear Bar...
If the duty cycle is exceeded, the printer may not print all of the information that was sent to it. NOTE: This is not a continuous batch printer.
Page 24
If the duty cycle is exceeded, the printer may not print all of the information that was sent to it. NOTE: This is not a continuous batch printer.
P r i n t i n g a T e s t R e c e i p t Before calling technical support, print a test receipt. The test receipt has the printer’s firmware version and other information on it.
S P E C I F I C AT I O N S P r i n t e r S p e c i f i c a t i o n s Height: Width: Length: Weight: w/ battery & supply Shipping Weight: Power: Operating Limits:...
Charging Time: Communications: Print Ratio S u p p l y S p e c i f i c a t i o n s Supplies: Supply Thickness: Supply Width: Supply Length: Roll Diameters: Maximum Print Area: Ordering Supplies 900148 2.2-inch wide supply, 10 roll case 900149 2.2-inch wide supply, 50 roll case...
Printhead Cleaning Pen (114226) Coiled Cable (125240) AC Adapter (125234) – Plugs into a wall outlet so the printer operates on AC current. Only for use with printers M09430R03, M09430R04, M09430R09, and M09430R10. Plug-in Charger (125225) – Plugs into an electrical outlet for charging the battery.