Download  Print this page

Patton electronics ENVIRONET EHA3201 Quick Start Manual

G.shdsl router
Hide thumbs

Advertisement

Model EHA3201
EnviroNET G.SHDSL Router

Quick Start Guide

Important
intended nor approved for use in an industrial or residential environment.
Part Number: 07MEHA3201-QS, Rev. C
Revised: February 16, 2012
—This is a Class A device and is intended for use in a light industrial environment. It is not
Sales Office: +1 (301) 975-1000
Technical Support: +1 (301) 975-1007
E-mail: support@patton.com
WWW: www.patton.com

Advertisement

loading

  Related Manuals for Patton electronics ENVIRONET EHA3201

  Summary of Contents for Patton electronics ENVIRONET EHA3201

  • Page 1: Quick Start Guide

    Model EHA3201 EnviroNET G.SHDSL Router Quick Start Guide Important —This is a Class A device and is intended for use in a light industrial environment. It is not intended nor approved for use in an industrial or residential environment. Part Number: 07MEHA3201-QS, Rev. C Revised: February 16, 2012 Sales Office: +1 (301) 975-1000 Technical Support: +1 (301) 975-1007...
  • Page 2 • Do not open the device when the power cord is connected. For sys- tems without a power switch and without an external power adapter, line voltages are present within the device when the power WARNING cord is connected. • For devices with an external power adapter, the power adapter shall be a listed Limited Power Source The mains outlet that is utilized to power the device shall be within 10 feet (3 meters) of the device, shall be easily accessible, and protected by a circuit breaker in compli-...
  • Page 3 Electrostatic Discharge (ESD) can damage equipment and impair electrical circuitry. It occurs when electronic printed circuit cards are improperly handled and can result in complete or intermittent failures. Do the follow- WARNING ing to prevent ESD: • Always follow ESD prevention procedures when removing and replac- ing cards.
  • Page 4: Connecting The Twisted-Pair Line Interface

    1.1 Grounding the EHA3201 Before installing the EnviroNET G.SHDSL Router, it is important to establish a good grounding connection first. Assemble a ground wire using #10 AWG wire with green-and-yellow-colored insulation and two ring ter- minals. Make the wire long enough to reach one of the following earth ground sources: The building ground rod (generally located at the site’s main service entrance) •...
  • Page 5: Connecting Power

    Figure 3. 1.4 Connecting Power The EHA3201 is an internally powered unit. The power connection is made via the 3-pin power connector on the bottom panel of the EnviroNET G.SHDSL Router. A mating connector is provided to create the mating cable (see 4).
  • Page 6 It does not matter whether the positive (+) or negative (-) side of the DC power supply is grounded. Note However, the polarity on the power source must be matched up properly to the EHA3201 power input (i.e. negative power source terminal to negative power input; positive power source terminal to positive power input).
  • Page 7: Configuring Applications

    2.2 Configuring applications The EHA3201 is typically used in a bridged or routed application. For instruction on how to configure the EHA3201 for an application, refer to the Model 3201 & 3241 User Manual. Bridged Applications For a bridged application connecting standalone units back-to-back, see pages 29-32 in the Model 3201 & •...
  • Page 8 B.0 EHA Case Specifications B.1 Power Requirements UAC: 110, 220VAC, 2.25W • B.2 Temperature Range -40–185°F (-40–85°C) • B.3 Humidity Up to 90% non-condensing. • B.4 Dimensions 8”H x 9.25”W x 3.25”D • B.5 Weight 6.4lb (2.9kg) • Note For Model 3201 unit specifications, refer to the www.patton.com/manuals.
  • Page 9: Compliance Information

    C.0 Compliance Information C.1 Compliance EMC: FCC Part 15, Class A • EN55022, Class A • EN55024 • Safety: UL 60950-1/CSA C22.2 N0. 60950-1 • IEC/EN60950-1 • AS/NZS 60950-1 • PSTN Regulatory: FCC Part 68 • CS-03 • AS/ACIF S043:2003 •...
  • Page 10: Industry Canada Notice

    3.3 Industry Canada Notice This equipment meets the applicable Industry Canada Terminal Equipment Technical Specifications. This is con- firmed by the registration number. The abbreviation, IC, before the registration number signifies that registra- tion was performed based on a Declaration of Conformity indicating that Industry Canada technical specifications were met.
  • Page 11: Ec Declaration Of Conformity

    C.5 EC Declaration of Conformity Models 3201 & 3241 Product Description: We certify that the apparatus identified above conforms to the requirements of Council Directive 1999/5/EC on the approximation of the laws of the member states relating to Radio and Telecommunication Terminal Equip- ment and the mutual recognition of their conformity.
  • Page 12: Copyright Statement

    Copyright statement Copyright © 2012, Patton Electronics Company. All rights reserved. The information in this document is subject to change without notice. Patton Electronics assumes no liability for errors that may appear in this document. Trademarks statement The term EnviroNET is a trademark of Patton Electronics Company. All other trademarks presented in this docu- ment are the property of their respective owners.
  • Page 13 D.0 Buccaneer 400 Series Environmentally Sealed Connectors The following instructions are provided by Bulgin UK for assembling the 400 Series Buccaneer IP68 Sealed Electrical IMPORTANT Cable Connectors. EHA3201 Quick Start Guide...
  • Page 14 EHA3201 Quick Start Guide...
  • Page 15 EHA3201 Quick Start Guide...
  • Page 16 EHA3201 Quick Start Guide...