Advertisement
Quick Links
Advertisement
Summary of Contents for Patriot PTX-NP400
- Page 1 NON PENETRATING ROOF MOUNTS PTX-NP400 PTX-NP550 PTX-NP658...
- Page 2 LIMITED TWELVE (12) MONTH WARRANTY This PATRIOT ANTENNA equipment is warranted to be free from defects in material and workmanship un- der normal use and service. PATRIOT ANTENNA shall repair or replace defective equipment, at no charge, or at its option, refund the purchase price, if the equipment is returned to PATRIOT ANTENNA not more than twelve (12) months after shipment.
- Page 3 PART # 295000 295001 295002 295003 295005 BRKT,NP DUALCORNER TIE (UNBENT) 295008 3HPPTXNP400 PREBAG,PTXNP400 HARDWARE SINGLE 3HPPTXNP400DT PTX-NP400 DESCRIPTION ASSY,NP TRAY ANGLE BRKT,NP CORNER TIE ASSY,NP FOOT CHANNEL,NP LEG ASSY,NP400 PIPE PREBAG,PTXNP HARDWARE DUAL PTX-NP550 DESCRIPTION ASSY,NP TRAY ANGLE BRKT,NP CORNER TIE...
- Page 6 NP Tray Angle Assemblies (prt# 295000) NP Corner Tie Bracket (prt# 295001) DETAIL A SCALE 1 : 4 3/4”nc X 1-3/4” Bolt, Washer, & Nut Channel Leg (prt# 295003) 3/4”nc X 2” Bolt, Washer, & Nut Bolt, Washer, & Nut 1) Lay out 8 NP TRAY ANGLE Foot Assembly (prt# 295002)
- Page 7 NP Tray Angle Assemblies (prt# 295000) NP Corner Tie DETAIL A SCALE 1 : 6 Bracket 3/8”nc X 1-3/4” (prt# 295001) Bolt, Washer, & Nut Channel Leg (prt# 295003) Foot Assembly 3/4”nc X 2” Bolt, Washer, & Nut DETAIL B SCALE 1 : 6 3/4”nc X 2”...
- Page 8 NP Tray Angle Assemblies (prt# 295000) NP Corner Tie Bracket (prt# 295001) 3/8”nc X 1-3/4” Bolt, Washer, & Nut DETAIL A SCALE 1 : 10 Channel Leg (prt# 295003) Foot Assembly (prt# 295002) 3/4”nc X 2” Bolt, Washer, & Nut DETAIL B SCALE 1 : 6 3/4”nc X 2”...
- Page 9 Ballast Requirement Charts 1. Determine the Wind Speed requirement for the installation, and the Elevation Angle of the antenna. 2. Look up the required ballast for the antenna size being used. 3. Load the Base Trays with the required ballast using 4 x 8 x 16in solid cement blocks. Elevation Ballast Required (lbs)at (Degrees)
- Page 10 Grounding Grounding Antenna Feed Cables 1. Ground antenna feed cables in accordance with current National Electric code and local electric codes. The illustration shows a typical grounding method. Clamps that provide a solid connection between ground wire and a ground source should be used.
-
Page 12: Specifications
Specifi cations Antenna Size Pole Size Materials Mount weight (single tray) Mount weight (double tray) Mount weight (triple tray) Ballast Load (single tray) Ballast Load (double tray) Ballast Load (triple tray) 1.8m through 3.1m 4” & 5-1/2” OD Powder Coated Steel 375 lbs 575lbs 775lbs...