Advertisement
Quick Links
Dimension anD insTallaTion guiDe
moDels:
SB926SL, SB916WL, SB916SL, SB908WL, SB908SL
IMPORTANT
• T hese instructions are a guide only. For complete installation
instructions, refer to the manual provided with the product.
• I f you do not follow the installation instructions your
dishwasher will not be properly installed. The product
warranty does not cover incomplete or improper
installation. You will be charged a service fee for any
service call to rectify improper or incomplete installation.
• T hese instructions apply to built-under applications only.
• I f your dishwasher is fitted with a water inlet hose with safety
valve, you will need an opening of at least 45mm x 90mm
in your cupboards in order to feed the hose through it.
Dishwasher Dimensions
The dimensions shown below are in millimetres. The height of
820mm is with the levelling legs screwed in at the minimum height.
100mm
595mm
Typical builT-unDer insTallaTion
There should be a minimum
2mm gap between the top of
the dishwasher and
underside of bench top
should be equal and no greater
WHDWINSTALL_ Jun08
820mm
180mm
50mm
555mm edge of door
120mm
585mm centre of door
The hose should not be
extended by more than
2 metres or water pump-out
problems may occur
Secure dishwasher with
brackets and screws provided
DISHWASHER
Gap on both sides
than 3mm per side
Kickplate fixing screws
If floor is not level, adjust
levelling legs to suit
cupboarD opening Dimensions
The dimensions shown below are in millimetres. The opening
allows for some clearance so that the dishwasher can be
pushed into place.
Note: if the opening is greater than 600mm wide then a
suitable width filler piece should be secured to the cupboard
before installing the dishwasher.
Fix drain hose max of
10mm below the top of
the dishwasher
SINK
600mm max -
300mm min
1000mm max
POWER OUTLET
POWER SUPPLY
230/240V–10Amps
built-under dishwashers
Remove entire plastic
membrane from sink trap
spigot & fit drain hose to
spigot with clamp
TAP CONNECTION
If cold-water pressure is
in excess of 800kPa, a
pressure-reducing valve
should be used.
Check for leaks.
INLET WATER SUPPLY
Water flow rate 10L/minute min
o
Water temperature 60
C max
Water pressure cold water:
800kPa max - 50kPa min
Water pressure hot water:
350kPa max - 50kPa min
Cold water recommended
© 2008 Electrolux Home Products Pty Ltd
WDIMSB926SL, WDIMSB916WL, WDIMSB916SL,
WDIMSB908WL, WDIMSB908SL Current as at June 2008
1
Advertisement
Related Manuals for Westinghouse SB926SL
Summary of Contents for Westinghouse SB926SL
- Page 1 Dimension anD insTallaTion guiDe built-under dishwashers moDels: SB926SL, SB916WL, SB916SL, SB908WL, SB908SL cupboarD opening Dimensions IMPORTANT The dimensions shown below are in millimetres. The opening allows for some clearance so that the dishwasher can be • T hese instructions are a guide only. For complete installation pushed into place. instructions, refer to the manual provided with the product. • I f you do not follow the installation instructions your Note: if the opening is greater than 600mm wide then a dishwasher will not be properly installed. The product...
- Page 2 levelling CAUTION Good levelling is essential for correct closure and sealing of the door. No further openings for venting of the dishwasher are When the appliance is correctly levelled, the door will not required, but only to let the water fill and drain hose and catch or rub on either side of the cabinet. power supply cable to pass through. Leave a space of 2mm between the top of the dishwasher and the underside of the kitchen counter. The height of the recess where the dishwasher is to be installed can vary between 825mm and 885mm from the floor since the dishwasher is fitted with adjustable feet (max. 60mm). Leave a space of 2mm between the top of the dishwasher and the underside of the kitchen counter. FiTTing The sTeam proTecTion Fit the steam protection onto the front part of the worktop, Check if the...
- Page 3 connecTion To waTer supply CAUTION The inlet hose should be inspected every 12 months for deterioration and replaced if necessary. Please take care when installing the safety inlet hose: • T he distance between the bottom edge of the safety valve • Cold water connection and the floor on which the dishwasher is standing must be – We recommend connection to a cold water supply. at least 300mm. – W ater pressures between 50kPa and 800kPa are • T he electrical cable for the safety valve is in the double- acceptable. walled water inlet hose. Do not immerse the water inlet – A pressure-reducing valve must be fitted if the cold water hose or the safety valve in water. supply exceeds 800kPa. (Refer also to the remarks in the • Do not attempt to shorten the inlet hose.
- Page 4 • N ever unplug the appliance by pulling on the cable. Always pull the plug. • E nsure that the dishwasher has been tested using the rinse & hold or quick 30 cycle and that the dishwasher fills with water, washes and drains with no leaks. The manufacturer accepts no liability for failure to observe the above safety precautions. For further information on all Westinghouse appliances, call into your Retailer, phone our Customer Care centre on 1300 363 640 or visit www.westinghouse.com.au © Copyright 2008 Electrolux Home Products Pty Ltd ABN 51 004 762 341 WHDWINSTALL_ Jun08...