1. Manuals
  2. Brands
  3. Paradyne Manuals
  4. Network Hardware
  5. Hotwire 8785
  6. Installation instructions manual

Paradyne Network Adapter 8785 Installation Instructions Manual

Tdm sdsl termination units
Hide thumbs Also See for Network Adapter 8785:
Table of Contents

Advertisement

Quick Links

Download this manual See also: User Manual
Hotwirer TDM SDSL Termination Units
Models 8775 and 8785

Installation Instructions

Document Number 8700-A2-GN15-20
February 2001

Product Documentation Online

Complete documentation for this product, including configuration options and cable pin
assignments, is available at www.paradyne.com. Select Library
Hotwire DSL & MVL Systems.
Select the following document:
8700-A2-GB25
Hotwire TDM SDSL Termination Units, Models 8775 and 8785, User's Guide
For information about the DSLAM or MCC, select from the following documents:
8000-A2-GB22
Hotwire Management Communications Controller (MCC) Card, IP Conservative,
User's Guide
8000-A2-GB29
Hotwire Management Communications Controller (MCC) Card
User's Guide
8610-A2-GN10
Hotwire 8610 DSLAM Installation Instructions
8810-A2-GN11
Hotwire 8810 DSLAM Installation Instructions
8820-A2-GN10
Hotwire 8820 GranDSLAM Installation Instructions
To order a paper copy of a Paradyne document:
H
Within the U.S.A., call 1-800-PARADYNE (1-800-727-2396)
H
Outside the U.S.A., call 1-727-530-8623
1
Technical Manuals

Advertisement

Table of Contents
loading

Related Manuals for Paradyne Network Adapter 8785

Summary of Contents for Paradyne Network Adapter 8785

  • Page 1: Installation Instructions

    8610-A2-GN10 Hotwire 8610 DSLAM Installation Instructions 8810-A2-GN11 Hotwire 8810 DSLAM Installation Instructions 8820-A2-GN10 Hotwire 8820 GranDSLAM Installation Instructions To order a paper copy of a Paradyne document: Within the U.S.A., call 1-800-PARADYNE (1-800-727-2396) Outside the U.S.A., call 1-727-530-8623 Technical Manuals...

  • Page 2: Installation Overview

    Hotwire TDM SDSL Termination Units Hotwirer 8775 and 8785 TDM SDSL Termination Units are circuit card assemblies comprising four Time Division Multiplexer Symmetric Digital Subscriber Line (TDM SDSL) ports and four synchronous ports. When the Hotwire 87xx TDM SDSL Termination Unit is used in a Hotwire 8600 or 8800 Series Digital Subscriber Line Access Multiplexer (DSLAM), it transports up to 2048 kbps signals over traditional twisted-pair telephone wiring.
  • Page 3 Plug-ended 50-position Telco cable for connection from the Hotwire DSLAM to the Main Distribution Frame (MDF) or other demarcation point. For the DTE connection, one of the following: V.35: 100-position plug-to-four MS34 (like Paradyne Feature No. 8700-F1-501) X.21: 100-position plug-to-four DB15 (like Paradyne Feature No. 8700-F1-502) RS-449: 100-position plug-to-four DB37 (like Paradyne Feature No.
  • Page 4 Installing TDM SDSL Cards A Hotwire TDM SDSL Termination Unit can be installed, removed, and replaced without disrupting service to other cards in the chassis. HANDLING PRECAUTIONS FOR STATIC-SENSITIVE DEVICES This product is designed to protect sensitive components from damage due to electrostatic discharge (ESD) during normal operation.
  • Page 5 — For a Hotwire 8800 Series DSLAM – Hold the unit vertically, with the component side facing right, and insert it into the top and bottom card guides. 4. Slide the unit into the slot until the power and network connectors seat firmly in the mating connectors on the backplane.

  • Page 6: Connecting To The Dte

    Connecting to the DTE Connection to the four ports of the unit is through the 100-pin connector on its faceplate. Use one of the DTE cables listed under Cables You Need on page 3. " Procedure To connect the Hotwire 87xx TDM SDSL Termination Unit to your DTE: 1.
  • Page 7 2. If necessary to attach the cable connector firmly in place, replace the longer Telco cable captive screw with a shorter one. Fasten the connector. 3. Insert a cable tie (provided with Hotwire DSLAM) through the tie mount to hold the 50-position Telco connector in place.

  • Page 8: Front Panel Leds

    Front Panel LEDs The following table describes the meaning and states of the LEDs on the Hotwire 8775 or 8785 TDM SDSL Termination Unit’s faceplate. Type SYSTEM OK SYNC PORT PORT LINK-UP * Slow Cycling: Fast Cycling: Pulsing: SDSL 8775 00-15834-03 LED is .

  • Page 9: Logging In To The Hotwire Dslam

    Logging In to the Hotwire DSLAM You can log in to the Hotwire DSLAM system using either a local VT100-compatible terminal or a remote Telnet connection. After you enter your user ID and password, the system displays the Hotwire Chassis Main Menu.

  • Page 10: Entering Identity Information

    Entering Identity Information After accessing your unit for the first time, use the Change Identity screen to determine SNMP administrative system information that will be displayed on the Identity screen of the Status branch. To access the Card Identity screen, follow this menu selection sequence: Main Menu Control...

  • Page 11: Configuration Edit/Display

    Configuration Edit/Display The Configuration Edit/Display screen is displayed when the current, customer, or default configuration is loaded and allows groups of configuration options to be displayed. To access the Configuration Edit/Display screen, follow this menu selection sequence: Main Menu Configuration –...

  • Page 12: Warranty, Sales, Service, And Training Information

    Document Feedback We welcome your comments and suggestions about this document. Please mail them to Technical Publications, Paradyne Corporation, 8545 126th Ave. N., Largo, FL 33773, or send e-mail to userdoc@paradyne.com. Include the number and title of this document in your correspondence. Please include your name and phone number if you are willing to provide additional clarification.

This manual is also suitable for:

8775

Table of Contents