Advertisement
Quick Links
Advertisement
Related Manuals for ParaBody 917101
Summary of Contents for ParaBody 917101
- Page 1 917101 SMITH MACHINE ASSEMBLY INSTRUCTIONS Part # 6"~ 15001 Revision: 06/09/97...
- Page 2 2. Do not allow minors or children to play on or around this equipment.. 3. Exercise with care to avoid injury. 4. If unsure of proper use of equipment, call your local Parabody distributor or call the Parabody customer service department at (800) 328-9714.
-
Page 3: Parts List
DESCRIPTION PART # KEY’ ~712002 BEARING HOUSING 6711402 SAFETY STOP 6711203 LOWER SUPPORT SLEEVE ASS~LY 6708901 LEFT SAFETY HOOK 6711601 RIGHT SAFETY HOOK 6711701 SMITH BAR 6710201 BAR STOP 6710102 LEFT UPRIGHT 6710503 RIGI-1T UPRIGHT 6710403 UPPER SUPPORT 6710803 CHROME ANGLE 6709001 80"... - Page 4 FIGURE 2 STEP 2: ¯ CAREFULLY lower on,e COUNTER WEIGHT (14) do~-n into the LEFT UPRIGHT (9) & RIGBT UPR][GHT (10) untiI bottoms out as sho~vn in FIGURE 2. I l J_l I I I...
- Page 5 FIGURE 3 STEP 3: ¯ LOOSELY assemble the LOWER SUPPORT (3) and ~’o PLATE HOLDER (15) to the LEFT & RIGHT UPRIGHTS 10) using four 1/2 X 4-1/2" BOLTS (16) and four 1/2" LOCK NUTS (21) as shown in FIGURE...
- Page 6 FIGURE 4 STEP 4: ¯ SECURELY assemble fottr PLATE HOLDERS (15) to the LEFT & RIGHT UPRIGHTS (9 & 10) using eight 1/2 BOLTS (17), eight 1/2" WASHERS (20), and eight 1/2" LOCK N-t~TS (21) as sho~a in FIGURE...
- Page 7 X 4"~ FIGURE 5 STEP 5: LOOSELY assemble t~vo CHROME .ANGLES (12) to the top of the LEFT & RIGHT UPRIGHTS (9 & 10) using four 1/2 4-1/2" BOLTS (16), and four 1/2" LOCK NUTS (21) as shown in FIGURE 5. (NOTE: MAKE SIYI~E CABLE IS BETWEEN THE TWO BOLTS.) LOOSELY assemble the CHROME .ANGLES (12) to the bottom of the LEFT &...
- Page 8 FIGURE STEP 7: ¯ Loop C.~BLE ASSEMBLIES (26) around the 4-1/2" PULLEYS (27) and route CABLE ASSENEBLY (26) back through UPPER SUPPORT (11)as shown in FIGURE 7. SECURELY assemble the 4-1/2" PUI_LEYS (27) to the UPPER SUPPORT (11) using t~’o 3/8 X 2" BOLTS (18) and ¯...
- Page 9 FIGURE 6 STEP 6: ¯ LOOSELY assemble UPPER SUTPORT (11) to the LEFT & RIGHT UPRIGHTS (9 & 10) u.~-in!~, two 1/2 X 4" BOLTS (17) two 1/2" WASHERS (20)and ~o I/2" LOCK NUTS (21)as shown in FIGURE 6. (NOTE: MAKE SURE CABLE ENSI~E OF THE 1/2"...
- Page 10 FIGURE 8 STEP 8: ¯ Insert va, o 80" GUIDE ftODS (13) through the BUSHENGS in the UPPER SUPPORT (11) and out lhrough the top, lower the GUIDE RODS (13) dovm into the BUSHING onthe BASE of the UPRIGHTS (9 & 10) a~; shown in FIGURE...
-
Page 11: See Figure
LEFT FIGURE 9 STEP 9: ¯ Slide one 1-1/2," THRUST BEARING (25), one RIGHT SAFETY HOOK (6), and one 1" SHAFT COLLAR (24) over SAFETY STOP (2) as shown in FIG~-R.E ¯ Slide one 1-1/2" THRUST BEARL~’G (25), one LEFT SAFETY HOOK (5), and one 1" SHAFT COLLAR (24) over SAFETY STOP (2) as sl~own in FIGURE ¯... - Page 12 FIGURE 11 STEP 11: ¯ Slide one BEARING HOUSING (1), one 2" SHAFT COLLAR (23), and one 2-1/2" OD RUBBER BUMPER (29) over SLEEVE ASSEMBLY (4) as shown in FIGURE 11. ¯ Using a 1/4" Allen wren,:h, SECURELY tighten each set screw on the 2" SHAFT COLLARS FIGURE 12 STEP 12: ¯...
- Page 13 STEP 13: ¯ Lift up each GUIDE ROD (13) and slide one 1" SHAFT COLLAR (24) over the bottom of each GUIDE ROD (13). Position 1" SHAFT COLLAR (24) half way up the GUIDE ROD (13) and tighten it using a 3/16" Allen wrench- See FIGURE 13. ¯...
- Page 14 BUSHING FIGURE 14 STEP 14: ¯ Lift up on each GUIDE ROD (13) aad slide the RIGHT & LEFT BAR STOP ASSEMBLIES GUIDE ROD (13) onto their respecfi~e sides then lock the HOOKS of the BAR STOPS (8) onto t~e CHROME (12) then seat GUIDE RODS (13) back into the BUSHINGS I l l l ~USHI...
- Page 15 FIGURE STEP 15: ¯ Loosen each 1" SHAFT COLLAR (24) and slide each one up firmly agains~ the BUSHINGS of the UPPER SUPPORT (11). See FIGURE 15. ¯ Using a 3/16" Allen ,~Tcnch, SECURELY tighten each set screw on the 1" SHAFT COLLARS (24).
- Page 16 FIGURE 16 STEP 16: ¯ SECURELY assemble threaded end of CABLE ASSEMBLIES (26) into the BEARING HOUSINGS (1) using one WASHER (20) on each .¢,~de as sho~-a in FIGLrRE 16. * NOTE: Lubricate the GUIDE RODS (13) with a light oil or lubricant that is available at most har,dware s~ores. 5 I~,,]...
- Page 17 STEP 17: ¯ MAKE SURE ALL CONNECTIONS ARE TIGHT! Thank you for purcha:;ing the Parabody 917101 Smith Machine. If unsure of proper use of equipment, call your local Parabody d~stributor or call the Parabody customer service department at (800) 328-9714.