Related Manuals for ParaBody 887
Summary of Contents for ParaBody 887
- Page 1 887 LAT OPTION USER’S GUIDE CLASS H PART # 7305601 REV. A WARNING: Read and follow all directions for each step to insure proper assembly of this product. Version: 887108 Revision: 06/20/02...
- Page 2 7. Inspect cables and their connections before using machine. Pay particular attention to the cable ends. DO NOT attempt to fix. Notify your authorized ParaBody dealer before use and have repairs made by an authorized service technician. 8. Make sure all spring loaded pull pins are fully engaged in the adjustment position and fully tighten thumbscrew before use.
-
Page 3: Tools Required For Assembly
Please note: * Thank you for purchasing the ParaBody 877 Lat Option. Please read these instructions thoroughly and keep them for future reference. This product must be assembled on a flat, level surface to assure its proper function. * This product must be assembled on a flat, level surface to assure its proper function. DO NOT securely tighten any frame connections until the entire frame has been assembled, unless otherwise stated. -
Page 4: Parts List
PART # DESCRIPTION LEA6800209 UPRIGHT LEA6800610 ADJ FOOT SUPPORT LEA6800809 PULLEY HOUSING LEA6801009 TOP BOOM LEA6801110 LAT BAR SUPPORT LEA6759810 CARRIAGE LEA6274410 LOW ROW BAR LEA6725310 LAT BAR LEA3116201 3-1/2” PULLEY LEA3116101 4-1/2” PULLEY LEA6802101 115-1/4” CABLE LEA6671601 121-3/4” CABLE LEA6692601 3 X 2”... - Page 5 UPRIGHT FRAME FIGURE 2 STEP 2: • NOTE: It may be necessary to loosen the 1/2 X 3-1/4” BOLTS of the LOWER CROSS SUPPORT connecting the UPRIGHT FRAME before beginning STEP 2. • Attach four 3/4 X 1-1/2” GLIDES (24) to the inside of the tube on the UPRIGHT (1) as shown in FIGURE 2 using the follow- ing steps: •...
- Page 6 FIGURE 3 STEP 3: • Insert two 2-1/2” ROUND END CAPS (19) into the ends of the ADJ. FOOT SUPPORT (2) as shown in FIGURE 3. • Insert one 1-3/4” END CAP (20) into the end of the ADJ. FOOT SUPPORT (2) as shown in FIGURE 3. •...
- Page 7 FIGURE 4 STEP 4: • Attach eight 1 X 1” GLIDES (15) to the ends the CARRIAGE (6) as shown in FIGURE 4 using the following steps: • Thoroughly clean all surfaces where the 1 X 1” GLIDES (15) are to be attached. •...
- Page 8 FIGURE 6 STEP 6: • NOTE: It may be necessary to loosen the 1/2 X 3-1/4” BOLTS of the UPPER CROSS SUPPORT connecting the UPRIGHT FRAME before beginning STEP 6. • LOOSELY assemble the TOP BOOM (4) to the UPRIGHT (1) using one 1/2 X 4” BOLT (28), one 1/2 X 3-1/2” BOLT (25), two 1/2” WASHERS (26), and one 1/2”...
- Page 9 FIGURE 8 3/8 X 2-3/4” 32 STEP 8: • Route the 115-1/4” CABLE (11) through the TOP BOOM (4) as shown in FIGURE 8. • SECURELY assemble three 3-1/2” PULLEYS (9) into the slots of the TOP BOOM (4) using three 3/8 X 2-3/4” BOLTS (32), six 3/8” FLANGE SPACERS (33), and three 3/8”...
- Page 10 FIGURE 9 STEP 9: • Attach the CABLE (11) from the TOP BOOM (4) to the CARRIAGE (6) using one 1/4” QUICK LINK (36) as shown in FIGURE 9. (IMPORTANT! Securely tighten QUICK LINK.) • Place one 3-1/2” PULLEY (9) into the loop of the CABLE (12) below the second and third PULLEY of the TOP BOOM (4) as shown in FIGURE 9.
- Page 11 FIGURE 10 STEP 10: • Route the threaded end of the 121-3/4” CABLE (12) through the slot of the PULLEY HOUSING then SECURELY assemble one 4-1/2” PULLEY (10) to the PULLEY HOUSING (3) using two 3/8 X 2-3/4” BOLTS (32), two 3/8” FLANGE SPACERS (33), two 3/8” WASHERS (30), and two 3/8”...
- Page 12 FIGURE 11 STEP 11: • Loop the 121-3/4” CABLE (12) around one 3-1/2” PULLEY (9) as shown in FIGURE 11. • LOOSELY assemble the 3-1/2” PULLEY (9) to the 3/16 X 1-3/4 X 5-1/4” PLATES (23) using one 3/8 X 2” BOLT (35), two 3/8” WASHERS (30), and one 3/8”...
- Page 13 • Attach the LOW ROW BAR (7) to the ball end of the lower CABLE (12) using one 12-LINK CHAIN (37) and two 5/16” SNAP HOOKS (34) as shown in FIGURE 12. Thank you for purchasing the Parabody 887 LAT OPTION. If unsure of proper use of equipment, call your local Parabody distributor or call the Parabody customer service department at (800) 328-9714.
- Page 14 Please note: * We recommend cleaning your product (pads and frame) on a regular basis, using warm soapy water. Touch-up paint can be purchased from your ParaBody customer service representative at (800) 328-9714. * Inspect equipment daily. Tighten all loose connections are replace worn parts immediately.
-
Page 15: Limited Warranty
ParaBody extends the following LIMITED WARRANTY to the original owner of the ParaBody products. The Warranty terms apply to IN HOME USE ONLY. 1. LIMITED WARRANTY ON FRAME AND WELDS. If the frame of the ParaBody product or a weld should crack or break, it will be repaired or replaced by ParaBody. - Page 16 Room 2610, Miramar Tower 132 Nathan Road, Tsimshatsui Kowloon, Hong Kong Phone: (852) 2891-6677 Fax: (852) 2575-6001 LIFE FITNESS www.parabody.com Life Fitness (UK) Ltd. Queen Adelaide Ely, Cambs CB7 4UB United Kingdom Phone CSS: (01353) 665507 Fax CSS: (01353) 666719 Life Fitness Benelux N.V.