Advertisement
Quick Links
Advertisement
Related Manuals for ParaBody 704101
Summary of Contents for ParaBody 704101
- Page 1 704101 REGGIE WHITE ALL PRO SYSTEM PRODUCT ASSEMBLY INSTRUCTIONS SHEETS I l/21195...
- Page 2 704101 REGGIE WHITE ALL PRO SYSTEM ASSEMBLY PARTS LIST SORT AND COUNT ALL PARTS BEFORE BEGINNING ASSEMBLY NAME/DESCRIPTION ITEM 3/8 X 6 IN. BOLT 3/8 X 3-I/4 IN. BOLT 3/8 X 3 IN. BOLT 3/8 X 2-3/4 IN. BOLT 3/8 X 2-I~2 IN BOLT 3/8 X 2 IN.
- Page 3 704101 REGGIE WHITE ALL PRO SYSTEM ASSEMBLY PARTS LIST SORT AND COUNT ALL PARTS BEFORE BEGINNING ASSEMBLY _WELDMENTS/PARTS’- NAME/DESCRIPTION ITEM UPRIGHT FRAME WLDMT PULLEY MOU,~,T FLAT ... ’_’.._ UPRIGHT WLDMI B,-,sE BAR ~ ~ ~’I~ ~’~{" ~ ~’I~ ~i"~ ...
- Page 4 LOOSE, UNTtL IYSTRUCTED SEQUENCES TO SECURELY TIGWrEN. IF" YOU EXPERIENCE ANY PROBLEM WITH THE ASSEMBLY OF THIS PRODUC’F, PLEASE CONTACT YOUR DEALER OR YOUR PARABODY CUSTOMER SERVICE REPRESENTATIVE AT: 1-800-328-9714 TOOLS REQUIRED: RATCHET, 9/16 ~UBBER MALLET or HAMMER Slide two (2) 2 IN. SQ. COVER CAPS over the ends of.:he BASE as shown on drawing.
- Page 5 704101 REGGIE WHITE ALL PRO SYSTEM ASSEMBLY INSTRUCTIC~NS Insert three (3) I-_: -: IN. SQ. END CAPS into the ends of the BEARING HOUSING as shown drawing. Slide the BEARING HOUSING down over the FRONT UPRIGHT of the UPRIGHT FRAME to the first set of holes ~ sb, own on drawing.
- Page 6 704101 REGGIE WHITE ALL PRO SYSTEM ASSEMBLY INSTRUCT, IONS~ Insert the LEFT and RIGHT PEC DEC ARMS through the 1/2 IN. FLANGE BEARINGS in the BEARING HOUSING on their respective two (2) ~ 2 IN. ID. PRESS-ON CAPS. Slide tx~o (2) 4 X 12 ROLLER PADS onto :he LEFT and RIGHT PEC DEC ARMS until PAD is ,:LUSH with the bottom of the ARMS.
- Page 7 REGGIE WHITE ALL PRO SYSTEM ASSEMBLY INSTRUCTI[ONS 704101 To install the HIGH PULLEY CABLE. start BALL over the TOP PULLEY on the PULLEY MOUNT FLATS. After the CABLE haz been routed SECURELY assemble one (1) 3/8 X ,.-~4 IN. BOLT, and one (I) 3/8 IN. LOCK NUT...
- Page 8 704101 REGGIE WHITE ALL PRO SYSTEM ASSEMBLY INSTRUCTIONS Assemble the LEFT and RIGHT ADJ. PAD SUPPORTS to the BENCH TOP as shown on drawing, " using one (!) 3/8 X 6 IN. BOLT, and one (1) 3/8 IN. LOCK NUT. (TIGHTEN THE CONNECTION ENOUGH TO REMOVE THE PLAY, YET ALLOWING THE ADJ.
- Page 10 Do not mark this box! Document: 11000;)-12...
- Page 11 REGGIE WHITEALL PRO GYMMUST BE ASSEMBLED ON A FLAT, LEVEL SURFACE TO ASSURE ITS PROPER FUNCTION. PARABODY STRONGLY RECOMMENDS THAT THIS PRODUCT BE ASSEMBLED BY TWO PEO-PLE TO AVOID POSSIBLE INJURY. ICEEP ALL FRAME CONNECTIONS LOOSE, UNTIL INSTRUCTED IN THE ASSEMBLY STEP SEQUENCES TO SECURELY TIGHTEN.
- Page 12 BUMPER, RUBBER 1-1/4 SQ ... BOLT, NYLON 3/8-16 X 2 BLK ... CAP, END 2 SQ 10-14 GA ... CAP, COVER 2SQ PARABODY LOGO CAP, MUSHROOM 9/16 OD ... PULLEY, 3-1/20D X 3/8 ID X 1 CHAIN, 12 LINK ...
- Page 13 705101 REGGIE WHITE ALL PRO GYM ASSEMBLY INSTRUCTIONS the 5-1/4 PLATE assembled in step 17. Connect the bottom CABLE to the CROSS BRACE using one QUICK DISCONNECT LINK, Insert the WEIGHT STACK SELECTOR PIN hato one of the WEIGHT PLATES. SECURELY TIGHTEN ALL LOOSE PULLEY CONNECTIONS AT THIS TIME.
- Page 14 705101 REGGIE WHITE Slide two (2) 2 1-N. SQ. COVER CAPS over the ends of the BASE as shown on drawing. Insert ali END CAPS into the WELDMENTS SECURELY assemble the UPRIGHT to the BASE as shown on drawing. BEFORE TIGHTENING CONNECTION MAKE SURE THAT THE UPRIGHT FRAME IS SQUARE TO THE BASE.
Need help?
Do you have a question about the 704101 and is the answer not in the manual?
Questions and answers