ParaBody 503 Assembly Instruction Sheet
ParaBody 503 Assembly Instruction Sheet

ParaBody 503 Assembly Instruction Sheet

Ex500 pec dec attachment

Advertisement

EX500
PEC DEC ATTACHMENT
503
PRODUCT-ASSEMBLY
INSTRUCTION SHEETS
II
TOOLS REQUIRED FOR ASSEMBLY:
9/16
INCH SOCKET
1/2
INCH SOCKET
ADJUSTABLE ~,VRENCH
HAMMER or
RUBBER MA.LLET
REVISION:
M
..
...-_...=.,:::.
:.: -:.:-: !.: ~i"-£~ .::".
If you experience any problems with the assembly of this product, please contact .. .. ....
.
.
....
~ , ,, ::~_. ...-.- r ~ .,,=-r .~,~ ~-.'~~:~
)'our dealer or your PARABODY
CuStomer Service representative at::_~ ._.~--- _~:~ r_~ ~' - : ;
.:L ~ '::.. ~ .~='.--:-:
....
.
.............

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 503 and is the answer not in the manual?

Questions and answers

Summary of Contents for ParaBody 503

  • Page 1 HAMMER or REVISION: If you experience any problems with the assembly of this product, please contact ..)’our dealer or your PARABODY PEC DEC ATTACHMENT RUBBER MA.LLET CuStomer Service representative at::_~ ._.~--- _~:~ r_~ ~’ - : ;...
  • Page 2 "" " 503 EXS00 PEC DEC ATTACHMENT ASSEMBLYPARTS LIST FOR STEP #1 & #2 SORT A~ND COUNT ALL PARTSBEFORE BEGINNING ASSEMBLY IJARDWARE: ITEM NAME/DESCRIPTION. .3/8 X 1-3!4 BOLT 3/8 X 2-3/4 BOLT 3/8 X 3 BOLT 3/8 X 3-I/4 BOLT...
  • Page 3 EXS00 PEC DEC ATTACHMENT ASSEMBLY PARTS LIST FOR~~ STEP & SORT AND COU]N’T ALL PA~RTS BEFORE BEGINNING ASSEMBLY... ~;WWEL PULLEY HARDWARE/PARTS: ITEM NAME/DESCRIPTION 3/8 X 3/4 BOLT 5/16 WASHER. : ... ~ ... : ... ~,..~ ... 2 LOW HEIGHT LOCK NUT 3/8 WASHER SWIVEL PULLEY...
  • Page 4 Carefully place the BEARING HOUSING and the BACK SUPPORT FRAME on the floor assemble them together before attaching them to the REAR RIGHT UPRIGHT, using one (1) 318 X BOLT, two (2) 3/8 WASHERS, one (I) 3/8 LOCK WASHER, and one (1) 3/8 Insert one (1) 2 IN SQ.
  • Page 5 EXS00 PEC DEC ATTACHMENT ASSEMBLYINSTRU~’iONS (STEP #1) Attach eight ($) PARAGLIDE STRIPS to the BACK SUPPORT FRAME as shown in DETAIL on (STEP #I SHEET #I of#2), using the following steps: ThoroughIy clean all inside and outside surfaces where the PARAGLIDE attached.
  • Page 6 503 EXS00 PEG DEC ATTACHMENT A~5~.E_M.J:$LY-I~STR.UL’I’IO~NS (STEe #2) THE ~RU~IONS FOR ~EP Loosely ~cmble one (I) CL~ to ~e PULLEY FLAT on ~e WEIGHT STACK S~PORT BASE, #3), using one (1) 3/8 X 1-3/4 BOLT, one (1) 3/8 LOCK WASHE~ ~d one (1) 3/8 ~. (SEE...
  • Page 7 ul I I" I ’1’...
  • Page 8 IlO, ¯ ~...

Table of Contents