Using The Cli To Configure Country Codes - Cisco 2100 Series Configuration Manual

Wireless lan controller
Hide thumbs Also See for 2100 Series:
Table of Contents

Advertisement

Configuring Country Codes

Using the CLI to Configure Country Codes

Follow these steps to configure country codes using the CLI.
To see a list of all available country codes, enter this command:
Step 1
show country supported
Enter these commands to disable the 802.11a and 802.11b/g networks:
Step 2
config 802.11a disable network
config 802.11b disable network
Step 3
To configure the country codes for the countries where your access points are installed, enter this
command:
config country code1[,code2,code3,...]
If you are entering more than one country code, separate each by a comma (for example, config country
US,CA,MX). Information similar to the following appears:
Changing country code could reset channel configuration.
If running in RFM One-Time mode, reassign channels after this command.
Check customized APs for valid channel values after this command.
Are you sure you want to continue? (y/n) y
Enter Y when prompted to confirm your decision. Information similar to the following appears:
Step 4
Configured Country............................. Multiple Countries:US,CA,MX
Auto-RF for this country combination is limited to common channels and power.
------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-
802.11BG
Channels
------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-
US (-AB)
CA (-AB)
MX (-NA)
Auto-RF
------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-
802.11A
Channels
--More-- or (q)uit
------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-
US (-AB)
CA (-ABN)
MX (-N)
Step 5
To verify your country code configuration, enter this command:
show country
Cisco Wireless LAN Controller Configuration Guide
7-52
KEY: * = Channel is legal in this country and may be configured manually.
A = Channel is the Auto-RF default in this country.
. = Channel is not legal in this country.
C = Channel has been configured for use by Auto-RF.
x = Channel is available to be configured for use by Auto-RF.
(-) = Regulatory Domains allowed by this country.
:
:
: 1 2 3 4 5 6 7 8 9 0 1 2 3 4
: A * * * * A * * * * A . . .
: A * * * * A * * * * A . . .
: A * * * * A * * * * A . . .
: C x x x x C x x x x C . . .
:
: 3 3 3 4 4 4 4 4 5 5 6 6 0 0 0 1 1 2 2 2 3 3 4 4 5 5 6 6
: 4 6 8 0 2 4 6 8 2 6 0 4 0 4 8 2 6 0 4 8 2 6 0 9 3 7 1 5
: . A . A . A . A A A A A * * * * * . . . * * * A A A A *
: . A . A . A . A A A A A * * * * * . . . * * * A A A A *
: . A . A . A . A A A A A . . . . . . . . . . . A A A A *
Auto-RF : . C . C . C . C C C C C . . . . . . . . . . . C C C C x
Chapter 7
1 1 1 1 1
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Controlling Lightweight Access Points
OL-17037-01

Hide quick links:

Advertisement

Table of Contents
loading

This manual is also suitable for:

4400 series

Table of Contents