Specifications - Panasonic WJ-SX650 Operating Instructions Manual

SPECIFICATIONS

■ Matrix Switcher WJ-SX650 Series
Power Source:
Power Consumption:
Ambient Operating Temperature:
Ambient Operating Humidity:
Video Input Board:
Camera Input (CAMERA IN 1 to 32):
Video Output (VIDEO OUT 1 to 4):
Alarm Input (ALARM IN):
RS-485 (Camera) Port:
Extension Port (EXTENSION IN 2, 3):
Video Output Board:
Monitor Output (MONITOR OUT 1 to 16): 1 V [P-P]/75 Ω (BNC x 16)
Data Port (DATA 1 to 4)
DATA 1, 2:
DATA 3, 4:
Alarm Output (ALARM OUT 1, 2)
Extension Port (EXTENSION 1 IN, OUT)*
Serial Port*:
Expansion slot:
RS-485 (Camera) Port*:
Functions:
Dimensions:
Weight:
1
* In the constant operation
2
* Available only when Video Input Board WJ-PB65C32 is mounted
3
* Not available when the MODE switches are set as Video Output Board 2
120 V AC, 60 Hz
60 W
–10 °C to +50 °C {14 °F to 122 °F}*
* In the constant operation
Less than 90 %
x 1
1 V [P-P]/75 Ω (BNC x 32), composite video signal
0.5 V [P-P]/75 Ω data signal and 2.5 V [P-P]/75 Ω vertical
plexed
1 V [P-P]/75 Ω (25-pin D-sub connector x 4)*
N.O. (Normally Open contact) or N.C. (Normally Close contact) selectable x 32
(37-pin D-sub connector)
6-conductor modular jack x 4 (2-wire or 4-wire communication, With termination
switches (MODE 1 to 4))
37-pin D-sub connector x 2
x 1
Terminal Mode (TMNL)/PS·Data (PS·DATA) selectable
Terminal Mode (TMNL)/Digital disk recorder (HDR) selectable
6-conductor modular jack x 4 (With termination switches (MODE 1 to 4))
Alarm Output: Open collector output x 32, Max. 24 V DC, 100 mA
Alarm Recover Output: Non-voltage make contact input x 16
3
Time Adjust Input* : Non-voltage make contact input x 1
3
Time Adjust Output* : Open collector output x 32, Max. 24 V DC, 100 mA
3
: 6-conductor modular jack x 2 (With a termination switch (TERM: ON, OFF))
VS Input*3: 1 V [P-P]/75 Ω (VS IN)
VS Output*3 (VS OUT (THRU)): VS loop-thru output
(VS OUT): 1 V {P-P}/75 Ω (VS)
9-pin D-sub connector x 2
x 1
6-conductor modular jack x 4 (2-wire or 4-wire communication, With termination
switches (MODE 1 to 4))*
Monitor control (Camera selection, tour sequence, group sequence, group pre-
set, OSD display)
Camera/Receiver control (Coaxial/RS-485 communication)
Recorder control
Alarm control (Alarm event, Alarm ACK, Alarm reset, Alarm suspension, Alarm
History Display)
Timer event, Camera event
420 mm (W) X 265 mm (H) X 372 mm (D)
{16-9/16" (W) X 10-2/5" (H) X
19.0 kg (42 lbs.)
1
2
, active loop-thru output
2
14-3/5" (D)} (excluding rubber feet and projections)
timing pulse multi-
95