Konica Minolta PagePro 9100 Repacking Manual
Konica Minolta PagePro 9100 Repacking Manual

Konica Minolta PagePro 9100 Repacking Manual

Hide thumbs Also See for PagePro 9100:

Advertisement

PagePro
9100
Repacking Guide
1760522-001A

Advertisement

Table of Contents
loading

Summary of Contents for Konica Minolta PagePro 9100

  • Page 1 PagePro 9100 ™ Repacking Guide 1760522-001A...
  • Page 2: Proprietary Statement

    Trademarks KONICA MINOLTA and the KONICA MINOLTA logo are trademarks or registered trademarks of KONICA MINOLTA HOLDINGS, INC. PagePro is a trademark or registered trademark of KONICA MINOLTA BUSINESS TECHNOLOGIES, INC. Crown and CrownView are trademarks or registered trademarks of KONICA MINOLTA PRINTING SOLUTIONS U.S.A., INC.
  • Page 3: Table Of Contents

    Introduction Storing the Printer “What do I do when storing the printer for an extended period?” page 1 “How do I care for media?” page 2 Deinstalling Accessories “How do I remove a duplexer?” page 2 “How do I remove a 4-bin mailbox?” page 2 “How do I remove an optional media tray?”...
  • Page 4: How Do I Care For Media

    How do I care for media? If media has been removed from its wrapper, place it in its original packaging and store in a cool, dark place. When storing media, avoid Moisture, excess humidity Keep media between 30% to 65% relative humidity. Toner does not adhere well to moist or wet paper On the other hand, media that has been stored for a long time without staying in its packaging may dry up too much and also cause jamming.
  • Page 5 Detach the duplexer from the printer. Attention If the duplexer is released too quickly, it may fall and break. Be sure to keep the duplexer supported until the screws are loosened. Using the wrench supplied with the duplexer, loosen the two screws on the duplexer.
  • Page 6: How Do I Remove A 4-Bin Mailbox

    How do I remove a 4-bin mailbox? Turn off the printer. Unplug the power supply cord and interface cable. Remove the four mailbins (trays) from the 4-bin mailbox. Disconnect the 4-bin mailbox cable from the connector on the printer. Press $. Unplug the connector %.
  • Page 7 Detach the mounting brackets from the two locations on the back of the printer. Loosen and remove the screws in front. (Use a coin to loosen the screws.) When deinstalling multiple optional media trays, remove each using the same procedure. After loosening the screws, lift the printer away from the optional media tray(s).
  • Page 8: Relocating The Printer

    Relocating the Printer How do I relocate my printer? Occasionally, you may have to move your printer to a different location, either nearby or to a distant location. To avoid damage to your printer, we advise you to follow the next instructions very carefully.
  • Page 9: Repacking The Printer

    PagePro 9100 Repacking Kit 2600713-100. For locations outside the Americas, refer to printer.konicaminolta.com. If you have been instructed to return the printer to KONICA MINOLTA PRINTING SOLUTIONS U.S.A., INC. by a customer support representative in the Americas, be sure to write the RMA (Return Merchandise Authorization) number you receive on the outside of the carton before calling the shipper for pickup.
  • Page 10 With another person’s help, put the printer into the plastic bag. WARNING! Your printer weighs approximately 61.7 lbs (28 kg) without consumables. Be sure to have help when lifting and moving it. Do not tilt it more than 1° in any direction at any time.
  • Page 11 Pack the printer for shipment as shown in the illustration. " # Ensure the shipping carton rests squarely on top of the base tray. If you’re also shipping the power cord and any manuals with the printer, place them in the shipping carton.
  • Page 12 Thread one end of the strapping beneath the carton. Pull the two ends of the strapping together at the top of the carton. Thread both ends up through the center of the buckle. Weave the slack of one end through the buckle. Pull the slack on that end so that the strapping is taut in the buckle.
  • Page 13: Shipping The Printer

    Repeat this procedure again, spacing the straps across the carton. Place the RMA number prominently on the carton. Shipping the Printer How do I ship the printer? If you need to ship your printer after installation, you must follow the procedures in this document to prevent damage to the printer and to keep your warranty valid.

Table of Contents