HP 5900 Series Configuration Manual page 48
Hide thumbs
Also See for 5900 Series:
- Command reference manual (364 pages) ,
- Configuration manual (190 pages) ,
- Compliance and safety manual (59 pages)
Table of Contents
Advertisement
[Sysname] irf member 1 renumber 4
Renumbering the member ID may result in configuration change or loss. Continue? [Y/N]:y
[Sysname] quit
<Sysname> reboot
# Connect Device D to Device B and Device C as shown in
Figure
16, and log in to Device D. This
example uses the SFP+ port group that contains Ten-GigabitEthernet 4/0/45 to
Ten-GigabitEthernet 4/0/48 for IRF connection.
# Shut down the physical ports.
<Sysname> system-view
[Sysname] interface range name irf interface ten-gigabitethernet 4/0/45 to
ten-gigabitethernet 4/0/48
[Sysname-if-range-irf] shutdown
[Sysname-if-range-irf] quit
# Bind Ten-GigabitEthernet 4/0/45 and Ten-GigabitEthernet 4/0/46 to IRF-port 4/1.
[Sysname] irf-port 4/1
[Sysname-irf-port4/1] port group interface ten-gigabitethernet 4/0/45
[Sysname-irf-port4/1] port group interface ten-gigabitethernet 4/0/46
[Sysname-irf-port4/1] quit
# Bind Ten-GigabitEthernet 4/0/47 and Ten-GigabitEthernet 4/0/48 to IRF-port 4/2.
[Sysname] irf-port 4/2
[Sysname-irf-port4/2] port group interface ten-gigabitethernet 4/0/47
[Sysname-irf-port4/2] port group interface ten-gigabitethernet 4/0/48
[Sysname-irf-port4/2] quit
# Bring up the SFP+ ports and save the configuration.
[Sysname] interface range name irf
[Sysname-if-range-irf] undo shutdown
[Sysname-if-range-irf] quit
[Sysname] save
# Activate the IRF port configuration.
[Sysname] irf-port-configuration active
Device D reboots to join the IRF fabric. A four-chassis IRF fabric is formed.
Configure ARP MAD on the IRF fabric:
5.
# Enable the spanning tree feature globally on the IRF fabric to prevent loops.
<Sysname> system-view
[Sysname] stp global enable
# Configure the IRF fabric to change its bridge MAC address as soon as the master leaves.
[Sysname] undo irf mac-address persistent
# Set the domain ID of the IRF fabric to 1.
[Sysname] irf domain 1
# Create VLAN 3, and assign Ten-GigabitEthernet 1/0/2, Ten-GigabitEthernet 2/0/1,
Ten-GigabitEthernet 3/0/2, and Ten-GigabitEthernet 4/0/1 to VLAN 3.
[Sysname] vlan 3
[Sysname-vlan3] port ten-gigabitethernet 1/0/2 ten-gigabitethernet 2/0/1
ten-gigabitethernet 3/0/2 ten-gigabitethernet 4/0/1
[Sysname-vlan3] quit
# Create VLAN-interface 3, assign it an IP address, and enable ARP MAD on the interface.
44
Hide quick links:
Advertisement
Table of Contents
