Yamaha P50-m Owner's Manual page 45

00000100 04 Sub-ID #1=Device Control Message
00000001 01 Sub-ID #2=Master Volume
0sssssss ss Volume LSB
0ttttttt tt Volume MSB
11110111 F7 End of Exclusive
When this is received, the Volume MSB will be reflected in
the System Parameter MASTER VOLUME setting.
3.1.2 Universal Non-realtime Messages
3.1.2.1 General MIDI Mode On
11110000 F0 Exclusive status
01111110 7E Universal Non-Real Time
01111111 7F ID of target device
00001001 09 Sub-ID #1=General MIDI Message
00000001 01 Sub-ID #2=General MIDI On
11110111 F7 End of Exclusive
Alternatively,
11110000 F0 Exclusive status
01111110 7E Universal Non-Real Time
0xxxnnnn xn Device No.xxx = don't care
00001001 09 Sub-ID #1=General MIDI Message
00000001 01 Sub-ID #2=General MIDI On
11110111 F7 End of Exclusive
This is not received when Rcv GM EXCLUSIVE = OFF.
This is not received when MIDI PROGRAM CHANGE
TABLE = OFF.
When an On message is received, the controller values will
be reset, and the voice number will be 09.REVERB and
CHORUS settings will be the settings of voice number 09.
3.1.3 XG Native Parameter Changes
11110000 F0 Exclusive status
01000011 43 YAMAHA ID
0001nnnn 1n Device No.
01001100 4C XG Model ID
0aaaaaaa aa Address High
0aaaaaaa aa Address Mid
0aaaaaaa aa Address Low
0ddddddd dd Data
| |
11110111 F7 End of Exclusive
Parameters with a Data Size of 2 or 4 transmit data of the
corresponding size.
3.1.3.1 XG Sytem On
11110000 F0 Exclusive status
01000011 43 YAMAHA ID
0001nnnn 1n Device No.
01001100 4C XG Model ID
00000000 00 Address High
00000000 00 Address Mid
01111110 7E Address Low
00000000 00 Data
11110111 F7 End of Exclusive
This is not received when MIDI PROGRAM CHANGE
TABLE = OFF.
When an On message is received, the controller values will
be reset, and the voice number will be 09.
REVERB and CHORUS settings will be the settings of
voice number 09.
3.1.3.2 XG System Data parameter change
Refer to tables <1-1> and <1-2>.
3.1.3.3 Multi Effect1 Data parameter change
Refer to tables <1-1> and <1-3>.
36
3.1.3.4 Part Data parameter change
3.1.4
3.1.4.1 P50-m System Data parameter change
3.1.4.2 Remote Switch
3.1.5
3.1.5.1 Master Tuning
3.2 Bulk Dump
3.2.1 XG Native Bulk Dump
SOUND LISTS & MIDI DATA
Refer to tables <1-1> and <1-4>.
P50-m Native Parameter Changes
11110000 F0 Exclusive status
01000011 43 YAMAHA ID
0001nnnn 1n Device No.
01010101 55 P50-m Model ID
0aaaaaaa aa Address High
0aaaaaaa aa Address Mid
0aaaaaaa aa Address Low
0ddddddd dd Data
| |
11110111 F7 End of Exclusive
Parameters with a Data Size of 2 or 4 transmit the corre-
sponding amount of data.
Refer to tables <2-1> and <2-2>.
Refer to tables <2-1> and <2-3>.
Other parameter changes
11110000 F0 Exclusive status
01000011 43 YAMAHA ID
0001nnnn 1n Device No.
00100111 27 Model ID
00000001 30 Sub ID2
00000000 00
00000000 00
0mmmmmmm mm Master Tune MSB
0lllllll ll Master Tune LSB
0ccccccc cc
11110111 F7 End of Exclusive
This message modifies the pitch of all channels at once.
This instrument receives the following bulk data.
[ XG NATIVE ]
1) XG System Data
2) Multi Effect1 Data
3) Part Data
[ P50-m NATIVE ]
1) P50-m System data
11110000 F0 Exclusive status
01000011 43 YAMAHA ID
0000nnnn 0n Device No.
01001100 4C XG Model ID
0bbbbbbb bb Byte Count
0bbbbbbb bb Byte Count
0aaaaaaa aa Address High
0aaaaaaa aa Address Mid
0aaaaaaa aa Address Low
00000000 00 Data
| |
0ccccccc cc Check-sum
11110111 F7 End of Exclusive
For the Address and Byte Count, refer to the accompanying
tables.
Check sum is the value which produces a lower 7 bits of
zero when the Start Address, Byte Count, and Check-sum
itself are added.