Disposal Information; Vacuuming With Accessories - Siemens VS08G Series Instructions For Use Manual

en de

Disposal information

Packaging
The packaging is designed to protect the
vacuum cleaner from being damaged
during transportation.
It is made of environment-friendly materials
and can be recycled.
Dispose of packaging that is no longer
required at an appropriate recycling point.
Used vacuum cleaners
Used vacuum cleaners contain many
recyclable materials.
Therefore, please take used vacuum
cleaners to your retailer or recycling centre
so that they can be recycled.
For current disposal methods, please
enquire at your appliance dealership or
local council.
!
Please note
Only connect the appliance to a socket
that is protected by at least a 16 amp fuse.
If a fuse should be tripped when you
switch on the vacuum cleaner, this may be
because other electrical appliances which
have a high current draw are connected to
the same power circuit.
To prevent the fuse from tripping, select the
lowest power setting before switching the
vacuum cleaner on, and increase the
power only once it is running.
Fold out picture pages.
Setting up
1
Figure
a)Push the hose connector into the opening
on the vacuum cleaner until it engages.
b)To remove the flexible hose, press the two
lugs together and pull the tube out.
2*
Figure
a)Connect the handle and the telescopic
tube together.
b)Push the handle into the telescopic tube
until it engages.
To release the connection, squeeze the
collar sleeve and pull the handle out.
3*
Figure
Attach the carpet lifter to the nozzle.
Press the carpet lifter sideways to engage.
4*
Figure
a)Connect the floor tool and the telescopic
tube together.
b)Push the telescopic tube into the
connecting piece of the floor tool until it
engages.
Press on the locking collar and pull out the
telescopic tube to disconnect.
Figure 5*
To adjust the length of the telescopic tube,
press the adjusting button/adjusting sleeve
in the direction of the arrow and adjust the
tube to the required length.
de en
6
Figure
a)Take the mains plug, pull the mains cable
to the required length and insert the plug
into a wall socket.
b)If your unit has an electronically actuated
cable rewind, the ready indicator will now
light up green.
7
Figure
To switch your vacuum cleaner on and off,
press the On/Off button in the direction of the
arrow.
8
Figure
The required suction power can be selected by
adjusting the suction regulator.
Low suction range:
For vacuuming delicate fabrics, e.g.
curtains.
Moderate suction range:
For daily vacuuming of lightly soiled floors.
High suction range:
For vacuuming durable floor coverings,
hard floors and for heavily soiled surfaces.
Vacuuming
You have bought an extremely powerful
device.
The highest suction setting is therefore only
recommended for heavily soiled, short-pile
carpets and hard floors.
9
Figure
Adjusting the floor tool:
For cleaning rugs
and carpets =>
For cleaning hard floors =>
Floor nozzle with carpet lifter*
Figure 10*
When you pull the floor tool backwards,
the rug is lifted, allowing you to clean
underneath its edge.

Vacuuming with accessories

11
Figure
Pull the combination tool in the direction of
the arrow to remove it from the tool holder.
a)Crevice nozzle
For vacuuming in crevices and corners.
For difficult to reach places, the
combination tool can be extended to two
different lengths by pulling out the crevice
nozzle.
For either length extension, pull the crevice
nozzle out until you hear it engage.
The crevice nozzle can be pushed back in
again by releasing the telescopic locking
mechanism (pressing it in the direction of
the arrow).
b)Upholstery nozzle
For cleaning upholstered furniture,
curtains, etc.
c)Furniture brush
For window frames, cabinets, profiles etc.
Fold the upholstery nozzle over in the
direction of the arrow.
To extend the brush ring, turn in the
direction of the arrow.
Before replacing the combination tool
in the tool holder, retract the brush
ring and fold the upholstery nozzle
back.
12*
Figure
When stopping cleaning for a moment, you
can use the parking aid on the back of the
vacuum cleaner.
Slide the plastic lug on the tool connector
into the groove at the back of the vacuum
cleaner.
If your cleaner has the automatic standby
function, it will now switch itself off.
=> Power indicator lights up "green".
* Depending on equipment