1. Manuals
  2. Brands
  3. Panasonic Manuals
  4. Projector
  5. PT-D5700
  6. Specifications

Panasonic DLP PT-D5700 Specifications

Panasonic projectors user's manual
Hide thumbs Also See for DLP PT-D5700:
Table of Contents

Advertisement

Quick Links

P ro d u c t N u m b e r :
P ro d u c t N a m e :
As of January 2009. Specifications subject to change without notice.
S
P
E
C
PT-D5700/D5700L
DLP
™
Projectors
F
I
L
E
The PT-D5700L is not equipped with a lens.
< 1 >

Advertisement

Table of Contents
loading

Related Manuals for Panasonic DLP PT-D5700

Summary of Contents for Panasonic DLP PT-D5700

  • Page 1 PT-D5700/D5700L P ro d u c t N u m b e r : P ro d u c t N a m e : As of January 2009. Specifications subject to change without notice. The PT-D5700L is not equipped with a lens. ™...

  • Page 2: Specifications

    ™ Projectors Specifications Main Unit Power supply: North America: Europe: Power consumption: North America: Europe: DLP™ chip: Panel size: Display method: Pixels: Lens: PT-D5700: PT-D5700L: Lamp: Screen size: Brightness* Center-to-corner uniformity* Contrast* Resolution: Scanning frequency: RGB: S-Video/Video: Optical axis shift: Keystone correction range: Installation: Terminals*...
  • Page 3 ™ Projectors On-screen menu: Dimensions (W x H x D): PT-D5700 PT-D5700L Weight* PT-D5700 PT-D5700L Operating temperature: Operating humidity: Remote Control Unit Power supply: Operation range* Wireless: Dimensions (W x H x D): Weight: Supplied Accessories Optional Accessories Replacement lamp unit: Ceiling mount bracket: Zoom lens (1.3–1.8:1) Zoom lens (2.4–4.0:1)
  • Page 4 ™ Projectors Dimensions unit : mm (inch) NOTE: This illustration is not drawn to scale. The illustration shows the PT-D5700. Terminals RGB IN connector pin assignment DVI-D output connector pin assignment signal T, M, D, S data 2- T, M, D, S data 2+ T, M, D, S data 2 shield DDC clock DDC clock...
  • Page 5 ™ Projectors Standard setting-up position (when installed using the ET-PKD56H) Upper edge of projected image Projected image Lower edge of projected image Projected image C A U T I O N The ET-DLE050 and ET-DLE055 have a fixed short-focus lens. Therefore, the lens shift function pro- vided in the main unit cannot be used.
  • Page 6 ™ Projectors Projection distance for 4:3 aspect ratio screen: ET-DLE100/DLE200/DLE310/DLE410/DLE050 Screen size (inch, diagonal) ET-DLE100 ET-DLE200 Zoom lens Zoom lens min. max. min. 1,335 1,812 2,454 1,611 2,184 2,958 1,887 2,556 3,462 2,163 2,928 3,966 2,439 3,300 4,470 2,715 3,672 4,974 3,267 4,416...
  • Page 7 ™ Projectors Projection distance for 4:3 aspect ratio screen: Supplied lens and ET-DLE150/DLE250/DLE350/DLE450/DLE055 Screen size (inch, diagonal) ET-DLE150 Supplied lens Zoom lens min. max. min. max. 1,344 1,967 1,785 2,376 1,623 2,370 2,155 2,864 1,903 2,773 2,525 3,352 2,183 3,177 2,895 3,840 2,462...

  • Page 8: Calculation Of The Projection Distance

    ™ Projectors Calculation of the projection distance For a screen size different from the above, use the equation below to calculate the projection distance. Aspect ratio 4:3 ET-DLE100 minimum maximum ET-DLE150 minimum maximum Supplied lens minimum maximum ET-DLE200 minimum maximum ET-DLE250 minimum maximum...
  • Page 9 • Floor mount (Width of projected image) 0.1H Installable angle Install the projector at an angle within the range shown below. • Vertical direction The projector may be installed at a vertical angle of 360°. As of January 2009 PT-D5700/D5700L •...

  • Page 10: List Of Compatible Signals

    NOTE: The native resolution of this projector is 1,024 x 768 pixels. If the display resolution of the input signal is different from the native resolution, image compression or expansion will be used to convert the input signal to a level within the native resolution.
  • Page 11 • It may not be possible to send or receive commands for about 10 to 60 seconds when the lamp is first turned on. If this occurs, wait for 60 seconds, then try sending or receiving again. • When sending multiple commands, be sure to wait for at least 0.5 second after receiving a response from the projector before sending the next command.
  • Page 12 1 Do not send PON, POF, OSH, or OLP commands continuously in a short period of time. Doing so may burst the lamp or shorten the lamp replacement cycle. 2 When a command that cannot be executed during standby mode is sent, the projector will send an ER401 command in reply.
  • Page 13 ™ Projectors Status asking commands Item Command : Parameter POWER CONDITION FREEZE SHUTTER INPUT SIGNAL TEST ON SCREEN PICTURE MODE SYSTEM QVX: D L V I 0 DAYLIGHT VIEW COLOR TINT COLOR TEMP. CONTRAST BRIGHTNESS SHARPNESS SET RUNTIME LAMP ON TIME Q$L: 1 (LAMP TIMER) Q$L: 2...

  • Page 14: Parameter Format

    <lamp power> <acctch> <color temp> <date> <time> NOTE: If a wrong command is received, the projector will send an ER401 command to the computer. Command example To set the on-screen display off, send the command as shown below. ADZZ Start ID Address NOTE: When sending commands without parameters, a colon (:) is not necessary.
  • Page 15 * Even when the ambient temperature near the intake opening is 40°C/104°F or lower, an accumulation of hot air inside the cabinet may cause the protective circuit to activate and shut down the projector. Please give ample consideration to the design with regard to ambient temperature conditions.

This manual is also suitable for:

Pt-d5700l

Table of Contents