User & Set-Up Instructions; General User Information; Control Set-Up Procedures; Start Operating Set-Up - Maytag MHN33PRCWW Installation Instructions Manual

Commercial front-load washer
Hide thumbs Also See for MHN33PRCWW:
Table of Contents

Advertisement

Available languages

Available languages

NOTE: After the washer has been installed and plugged in,
the display may show '0 MINUTES'. Once the washer has been
plugged in and the washer door opened and closed, the display
will show the price. In washers set for free cycles, the display will
flash 'SELECT CYCLE'.
1. PD Models: Insert coins until 'SELECT CYCLE' flashes
in display.
PR Models: A debit card is required rather than coins. In
Enhanced Debit mode, the card balance will also display
when a debit card is inserted into the reader.
2. Door must be closed before cycle selection is made,
3. Press fabric setting key pad for the wash cycle desired. After
the cycle is started, the time will display and count down.
4. If a cycle is interrupted by opening the door, 'RESELECT
CYCLE' will flash in the display. To restart the washer,
close door, and reselect desired cycle.

General User Information

SCROLLING 'OUT OF ORDER' SHOWING IN DISPLAY
This condition indicates the washer is inoperative.
'0 MINUTES' SHOWING IN DISPLAY
This indicates the cycle is complete and the washer cannot be
operated. Coins dropped or debit inputs during this condition will
be stored in escrow but cannot be used until normal operation
is restored by opening and closing the door. If a door switch fails,
it must be replaced before normal operation can be restored.
COLD START (Initial first use)
Washer is programmed at the factory as follows:
11-minute wash period
3 rinses (extra rinse not enabled)
$1.75 wash price (PD models)
$0 00 wash price (PR models)
WARM START (after power failure)
A few seconds after power is restored, if a cycle was in progress
at the time of the power failure, 'RESELECT CYCLE' will flash
in the display, indicating the need for a key press to restart the
washer.
DOOR LOCK
Prior to beginning a cycle, there is a door lock routine of lock/
unlock/relock; then cycle begins. The door will remain locked
until the end of a cycle or approximately 2 minutes after a power
interruption.
PRICING
After the door is opened following the completion of a cycle,
the display indicates the cycle price (unless set for free operation).
As coins are dropped or debit inputs arrive, the display will change
to lead the user through the initiation of a cycle.
FREE CYCLES
This is established by setting the cycle price to zero. When this
happens, 'SELECT CYCLE' will appear rather than a cycle price.
DEBIT CARD READY
This washer is debit card 'cable' ready. It will accept a variety of
debit card systems, but does NOT come with a debit card reader.
Refer to the debit card reader manufacturer for proper washer
set-up. In models converted to a Generation 1 debit card system,
debit pulses represent the equivalent of one coin (coin 1).
10
USER & SET-UP INSTRUCTIONS

Control Set-up Procedures

IMPORTANT: Read all instructions before operating.
PD Models: Insert access door key, turn, and lift to remove
access door.
PR Models: Once the debit card reader is installed (according
to the reader manufacturer's instructions), the set-up mode can
only be entered by inserting a set-up card (supplied by the reader
manufacturer) into the card slot. If a set-up card is not available,
diagnostic modes can be entered by removing connector AA1 on
the circuit board or by using the Service Access Code (see Service
Access Code section, page 14) for PR models set up as a PN.
The lower fabric setting key pads and the digital display are used
to set up the controls.
The display can contain 4 numbers and/or letters and a decimal
point. These are used to indicate the set-up codes and related
code values available for use in programming the washer.
HOW TO USE THE KEY PADS TO PROGRAM THE CONTROLS
1. POWER WASH – UPPER LEFT button is used to adjust the
values associated with set-up codes. Pressing the key pad
will increment the value. Rapid adjustment is possible by
holding the button down.
2. The TEMPERATURE – LOWER LEFT key pad is used to adjust
the values associated with set-up codes. Pressing the key
pad will decrement the value. Rapid adjustment is possible by
holding down the key pad.
3. The EXTRA RINSE – LOWER MIDDLE key pad will advance
through the set-up codes. Pressing the key pad will advance
to the next available set-up code. Holding the key pad down
will automatically advance through the set-up codes at a rate
of 1 per second.
4. The DELICATES – UPPER RIGHT key pad is used to select
or deselect options.

Start Operating Set-up

Before proceeding, it is worth noting that, despite all of the
options available, an owner can simply choose to uncrate a new
commercial washer, hook it up, plug it in, and have a washer
that operates.
Washers are preset at the factory for an 11-minute wash period
and 3 rinses (no extra rinse).
SET-UP CODES
The EXTRA RINSE – LOWER MIDDLE key pad will advance
you from code to code.
The TEMPERATURE – LOWER LEFT and POWER WASH –
UPPER LEFT key pads will change the code value.
The DELICATES – UPPER RIGHT key pad will select or
deselect options.
FOR PR MODELS: The set-up codes are the same as for the
"PD" model except where noted.
The set-up code is indicated by the one or two left-hand
characters. The set-up code value is indicated by the two
or three right-hand characters.

Hide quick links:

Advertisement

Table of Contents
loading

Table of Contents