Page of 20
hp LaserJet 1200

Advertising

   Related Manuals for HP LaserJet 1200

   Summary of Contents for HP LaserJet 1200

  • Page 1

    LaserJet 1200...

  • Page 2

    Consult your dealer or an experienced radio/TV technician. Any changes or modifications to the printer that are not expressly approved by HP could void the user’s authority to operate this equipment. Use of a shielded interface cable is required to comply with the Class B limits of Part 15 of FCC rules.

  • Page 3

    Review package contents. Make sure all parts are included. Prepare the location. Place on a sturdy, level surface. Allow space for 1) HP LaserJet 1200 series printer. 2) Toner cartridge (in protective bag). ventilation. Allow space behind the printer for output from the 3) Getting Started Guide.

  • Page 4

    Regulate the environment. Do not place in direct sunlight. Ensure the environment is free from abrupt temperature or humidity changes. • Temperature—10° to 32.5° C (50° to 91° F). • Relative humidity—20% to 80%. • —10° 32,5° C. • —20% 80%.

  • Page 5

    Assembly Open the toner door. Pull the sides of the door forward until the door Remove the left side panel. 1) Grasp the left side panel using the finger locks in its open position. Leave the door open until step 7. hole.

  • Page 6

    Connect USB or parallel cable to printer. The HP LaserJet 1200 printer Reattach the left side panel. 1) Insert the left side panel tabs behind the includes USB and parallel ports. Connect one cable to the proper port and edge of the front panel. 2) Swing the panel shut.

  • Page 7

    Prepare the toner cartridge. Remove the toner cartridge from the plastic Install the toner cartridge. Insert the cartridge into the printer, making bag. Remove the mylar tape by breaking the tab on the left and pulling the sure that the toner cartridge is in position. tape completely out.

  • Page 8

    Close the toner door. The toner cartridge engages when the door is Install the printer trays. 1) Leave the printer media input trays taped closed. together. 2) Slide the complete assembly in at an angle and then down until it fits securely in the printer. 3) Remove the tape and lift off the printer priority media input tray (top tray).

  • Page 9

    1) Place the media into the media input tray. Slide the guides until they are Test the printer. Wait until the ready light is illuminated and press the Go flush with the media. 2) Install the printer priority media input tray. button.

  • Page 10

    Install the printer software. Insert the CD for your software installation or Installing on Windows. 1) Select Software Installation from the autorun go to the Plug and Play section. screen. If autorun does not occur, select Start, select Run, and type x:\setup (where x is the letter of your CD-ROM drive).

  • Page 11

    3) Når installasjonen er fullført, kopler du I/U-kabelen til på nytt. 2) Kjør Apples Skrivebordsskriververktøy. 3) Velg HP Printer datamaskinen, og starter datamaskinen på nytt. (USB). 4) Klikk på Endre. 5) Velg HP LaserJet. 6) Klikk på Auto-oppsett og deretter Opprett. Macintosh (USB). 1) .

  • Page 12

    Jatka-painiketta. huolto- ja tukitiedoista. Gratulerar! Din HP LaserJet 1200-produkt är klar att använda. Om du Felsöka skrivaren. 1) Om inga lampor lyser kan du kontrollera hade några problem finns felsökningsinformation i den elektroniska nätsladden och därefter trycka på...

  • Page 13

    DIMM, if necessary. 4) If all lights are on, unplug the printer, wait check for media jams. 5 minutes, plug it back in, and retry. If errors still exist, call HP Customer Support. DIMM- .

  • Page 14

    Plug & Play Installing on Windows 98 and Millennium (USB). 1) Connect the I/O 5) Select Specify a location, then type x:\98Me_USB\ (where x is the cable to the computer. 2) Reboot the computer. 3) In the Add New letter of your CD-ROM drive). 6) Follow the instructions on your screen. Hardware wizard, click Next.

  • Page 15

    Installing on Windows 2000 (USB). 1) Connect the I/O cable to the 5) Select Specify a location. 6) Under Copy manufacturer’s files from, computer. 2) Reboot the computer. 3) In the Found New Hardware wizard, type x:\2000\ (where x is the letter of your CD-ROM drive), and click OK. click Next.

  • Page 16

    Installing on Windows 9X and Millennium (Parallel). 1) Connect the I/O 4) Select Search for the best driver for your device (recommended), cable to the computer. 2) Reboot the computer. 3) When the Installation and click Next. 5) Select Specify a location, then type x:\9xMe_LPT Wizard appears, click Next.

  • Page 17

    Installing on Windows NT (Parallel). (Note: You must have administrator Installing on Windows 2000 (Parallel). 1) Connect the I/O cable to the privileges.) 1) When the Installation wizard appears, click Software computer. 2) Reboot the computer. 3) In the Found New Hardware wizard, Installation.

  • Page 18

    5) Select Specify a location. 6) Under Copy manufacturer’s files from, type x:\2000\ (where x is the letter of your CD-ROM drive), and click OK. 7) Click Next. 8) Follow the instructions on your screen. Specify a location ( ). 6) Copy manufacturer’s files from ( x:\2000\ (...

  • Page 20

    2001 Hewlett-Packard Co. www.hp.com/support/lj1200 *C7044-90924* *C7044-90924* C7044-90924...

Comments to this Manuals

Symbols: 0
Latest comments: