Download Print this page
Panasonic KX-TC2000AL Operating Instructions
Panasonic KX-TC2000AL Operating Instructions

Panasonic KX-TC2000AL Operating Instructions

Panasonic cordless phone getting started guide

Advertisement

Quick Links

1
Getting Started
1-A Accessories
1-B Location of Controls
AC Adaptor......one
Battery.............one
Handset
Antenna
(TALK) Button and
Indicator (2-A)
Telephone Line Cord............................one
(AUTO) Button
(3-A, 5-D)
For Australia
For New Zealand
(DIRECT) Button
(4-A)
(RECALL)
DEF
ABC
3
Button (5-D)
1
2
JKL
MNO
GHI
5
6
4
(REDIAL) Button
(RINGER) Button
WXYZ
PQRS
TUV
9
7
8
For Australia only
(2-A)
Handset Cover
(2-B)
0
........................one
Telephone Plug
(PAUSE) Button
(PROGRAM) Button
........................one
(5-C)
(3-A, 4-A, 5-D)
(CH) (Channel)
(LOUD) Button (2-A)
Button (2-A)
RECHARGE
Charge Contacts
Indicator (6-A)
(6-A)
1-C Settings
1
Connect as shown.
2
Install the battery in the handset, and close the
handset cover, locking it into place.
Fasten the AC adaptor cord.
Hooks
For New Zealand
To Single-Line
To replace the battery:
Telephone Jack
OR
Press the notch on the cover firmly and
Telephone Line Cord
slide it as indicated by the arrow.
Replace the old battery with new one
For Australia
(6-A). Close the cover and charge for
To Socket
about 15 hours.
•Be sure wires are free from being pressed by the battery body
or the handset cover.
Extend the
Telephone
Telephone Plug
antenna fully.
Line Cord
3
Charge the battery for about 15 hours.
To Power Outlet
STOP
(AC 230 V–240 V,
•See section 6-A for more details.
50/60 Hz)
•The IN USE/CHARGE indicator lights.
AC Adaptor
•USE ONLY WITH Panasonic AC ADAPTOR PQLV16AL.
•The AC adaptor must remain connected at all times.
(It is normal for the adaptor to feel warm during use.)
•This unit will not function during a power failure. If you want to
connect a standard telephone on the same line;
- KX-TC2000AL: Use a telephone double adaptor.
- KX-TC2000NZ: Use a T-adaptor.
•KX-TC2000AL and KX-TC2000NZ are not designed to be used
with rotary (pulse dialling) services.
2
Making/Answering Calls
Section 1
2-A Making Calls
Base unit
Antenna (1-C)
Handset Hook (6-C)
IN USE/CHARGE
Indicator (1-C, 5-A)
(TALK) and
Indicator
(HANDSET!LOCATOR)
(REDIAL)
Charge
Button (5-A)
Contacts (6-A)
(LOUD)
(CH)
2-B Answering Calls
Black
Red
Lead
Lead
(TALK) and Indicator
(RINGER)
IN USE/CHARGE Indicator
3
Section 2
1
Press
.
(TALK)
To redial the last number dialled
•The TALK indicator lights.
Press (TALK) \ (REDIAL).
•If an alarm tone sounds, see 6-D.
To select the handset receiver
2
Dial a phone number.
volume
Press (LOUD) while talking.
•Each time you press the button, the
3
To hang up,
volume level will change to LOW (preset)
or HIGH.
press
(TALK)
or place the
handset on the base unit.
If noise interferes with the
•The indicator light goes out.
conversation
Press (CH) to select a clearer channel or
•For best operating performance, see
move closer to the base unit.
section 6-B.
•When dialling additional numbers after
Backlit handset keypad
speed dialling [eg, AUTO (3-B), DIRECT
(4-B) or REDIAL], make sure that speed
The handset dialling buttons will light when
dialling is finished before entering
you press a button or lift the handset off the
additional digits.
base unit, or when a call is received. The
lights will go out a few seconds after
Otherwise, the unit may not dial correctly.
pressing a button, lifting the handset or
answering a call.
4
If the handset is off the base unit,
Selecting the ringer volume
press
(TALK)
.
The TALK indicator light must be off.
•You can also answer a call by pressing
•To select HIGH (preset) or LOW,
any dialling button (0) to (9), (*) or (#)
press (RINGER).
(—Any Key Talk).
Each time you press the button, the ringer
volume will change and the selected
volume will ring.
•To turn the ringer OFF,
OR
press and hold (RINGER) until a beep
sounds.
•To turn the ringer ON,
If on the base unit,
press (RINGER).
just lift up.
For New Zealand Users Only: Additional Security Feature
In the event that a call cannot be made from the handset following a power interruption,
disconnect the base unit from the line momentarily then reconnect it. Turn the handset off, and
replace it on the base unit.
This will re-establish the security system and the handset can be used as before.
Speed Dialler
3-A Storing Phone Numbers in Memory
You can store up to 10 phone numbers. The dialling buttons ((0) to (9))
If you misdial
function as memory stations.
The TALK indicator light must be off before programming.
Press (PROGRAM) to end storing. \
\ Start again from step 1.
1
Press
.
(PROGRAM)
To erase a stored number
•The TALK indicator flashes.
Press (PROGRAM) \ (AUTO) \
2
Enter a phone number up
\ the memory station number ((0) to (9))
to 16 digits.
for the phone number to be erased.
•A beep sounds.
3
Press
.
(AUTO)
(AUTO)
4
Press a memory station
TALK Indicator
number (
to
).
(0)
(9)
Memory Station
Numbers
•A beep sounds.
•To store other numbers, repeat
(PAUSE)
steps 1 through 4.
•If a pause is required for dialling, press
(PROGRAM)
(PAUSE) where needed. Pressing (PAUSE)
counts as one digit (5-C).
One-Touch Dialler
4-A Storing a Phone Number in the DIRECT Button
A phone number stored in the (DIRECT) button can be dialled with a one-touch operation.
If you misdial
The TALK indicator light must be off before programming.
Press (PROGRAM) to end storing. \
\ Start again from step 1.
1
Press
(PROGRAM)
.
•The TALK indicator flashes.
To erase a stored number
Press (PROGRAM) \ (DIRECT).
•A beep sounds.
2
Enter a phone number up
to 16 digits.
(DIRECT)
3
Press
.
(DIRECT)
•A beep sounds.
TALK Indicator
•If a pause is required for dialling, press
(PAUSE) where needed. Pressing
(PAUSE)
(PAUSE) counts as one digit (5-C).
(PROGRAM)
Speed Dialler
Section 3/4
3-B Dialling a Stored Number
1
Press
.
(TALK)
•The TALK indicator lights.
2
Press
.
(AUTO)
•The TALK indicator flashes.
(TALK) and
Indicator
(AUTO)
3
Press the memory
station number
Memory Station
(
(0)
to
(9)
).
Numbers
•The stored number is
dialled.
One-Touch Dialler
4-B Dialling a Stored Number in the DIRECT Button
1
Press
.
(TALK)
•The TALK indicator lights.
2
Press
.
(DIRECT)
•The stored number is
dialled.
(DIRECT)
(TALK) and
Indicator

Advertisement

loading

Summary of Contents for Panasonic KX-TC2000AL

  • Page 1 •This unit will not function during a power failure. If you want to connect a standard telephone on the same line; - KX-TC2000AL: Use a telephone double adaptor. - KX-TC2000NZ: Use a T-adaptor. •KX-TC2000AL and KX-TC2000NZ are not designed to be used with rotary (pulse dialling) services. Making/Answering Calls Section 2...
  • Page 2 The recall time depends on your telephone exchange or host PBX. You can select the following recall times: “90, 100, 110, 250, 300, 400, 600 or 700 msec (milliseconds)”. KX-TC2000AL comes from the factory set to “100 msec” and KX-TC2000NZ comes set to “600 msec”.