Table of Contents
Advertisement
Warning system table
When trouble is detected immediately after the power is turned on or during operation, the user is alerted
by the power display LED and beep sound (provided that "ON" is selected for the "BEEP SOUND" setting
on the setting menu "OTHER FUNCTIONS" (Page 106)).
Type of
LCD monitor screen
Priority
warning
SYSTEM ERROR
Cause displayed *
1
System error
blinks in red.
P2 card
TURN POWER OFF
2
ejection
Blinks in red.
trouble
LOW BATTERY
Blinks in red. Blinks with
the remaining battery
Low battery
3
display empty. (This
charge
display appears even
when it has been set to
OFF on the setting menu.)
Blinks in red (display
4
P2 card full
appears only for 3
seconds when [REC] is
REC WARNING
Recording
Cause displayed *
5
trouble
blinks in red.
One block on the
remaining battery
Near low
display is blinking. (This
6
battery
display appears even
charge
when it has been set
to OFF on the setting
P2 card
Remaining media
7
nearly full
memory display blinks.
Input image
frame
8
distorted
IRREGULAR FRM SIG
during
recording
*
1 P2 SYSTEM ERROR Cause display
•
P2 MICON ERROR: P2 microprocessor does not respond.
•
P2 CONTROL ERROR: Trouble has occurred in the P2 recording control.
•
REC RAM OVERFLOW: Recording RAM overflow
*
2 REC WARNING Cause display
CARD ERROR * : P2 card trouble (slot number of trouble card is displayed in
•
•
REC RAM OVERFLOW: Recording RAM overflow
•
ERROR: Other recording trouble
*
3 The warning is cleared when any one of the following operations is performed.
•
When a playback function button (STOP, PLAY, STILL, FF or REW) is pressed
•
When the PC mode is selected while [THUMBNAIL/MODE] is held down for more than 2 seconds
•
When a P2 card has been ejected or another card has been inserted
*
4 The warning is cleared when any one of the following operations is performed.
•
When a playback function button (STOP, PLAY, STILL, FF or REW) is pressed
•
When a P2 card has been ejected
Power display
display
LED
Blinks at a
1
,
rate of 4 times
per second.
Blinks at a
rate of 4 times
per second.
Blinks at a
rate of once
per second.
Blinks at
FULL
P2
a rate of 4
times per
second upon
completion of
pressed).
recording.
Blinks at a
,
rate of 4 times
2
per second.
Blinks at a
rate of once
per second.
menu.)
Blinks at a
rate of once a
second during
recording.
Blinks at a
rate of once a
second during
recording.
Warning description and
Beep sound
record/playback operation
P2 microprocessor or
Beeps
control trouble. Operation
continuously.
is stopped.
Trouble has occurred in the
internal memory because a
Beeps
P2 card was ejected while
continuously.
its data was being accessed.
Both access LEDs blink in
orange (4 Hz).
The battery charge is low.
Recording or playback
Beeps
stops. If the voltage falls
continuously.
further, the power is
automatically turned off.
Beeps
There is no more free
continuously
memory left on the P2
upon
card. Recording is
completion of
stopped *
recording.
Beeps
intermittently
Recording trouble.
at a rate of
Recording is stopped *
4 times per
second.
The battery charge is
None
falling to low. Operation is
continued.
Under 2 minutes of
memory remaining on
the P2 card (remaining
None
memory display shows
less than one minute).
This warning appears only
during recording.
Recording stops due to
Beeps
the input signal distortion.
intermittently
The recording will
at a rate of
automatically resume
2 times per
when input signals are
second.
stabilized.
Action to be taken
Check the cause
display *
1
, and consult
your vendor.
Turn off the power.
If something is wrong
with the clips on the
ejected P2 card, repair
them.
Replace the battery.
Delete the unnecessary
clips or insert a new
card.
3
.
Turn off the power and turn
it back on. Then check
the recording/playback.
.
Replace the P2 card
4
if recording cannot be
performed properly.
Replace the battery as
necessary.
Replace the P2 card
or add another card as
necessary.
Check the input signals.
*
)
10
Hide quick links:
Advertisement
Table of Contents
