Bosch SHX3AR75UC Operating Instructions Manual page 15

For Models with Display
To enter options mode:
1
Press the On/Off button to turn the unit on.
2
The countdown display and one of the wash cycle LEDs will be flashing.
3
Press and hold down the > button, then simultaneously press and release the Start button. Now release the > button.
4
The "Sanitized" LED will be flashing. You are now in options mode.
5
Press the > button to select the option you would like to adjust.
To set amount of Rinse Aid:
NOTE: If your glasses have spots on them, you need more rinse aid. If your glasses have streaks on them, you need less rinse aid.
1
Follow the above instructions to enter options mode.
2
With the display showing "r:00" - "r:06" press the < button to change the amount of rinse aid dispensed.
r:00 = rinse aid is OFF
r:03 = medium amount of rinse aid dispensed
r:06 = highest amount of rinse aid dispensed
3
Press Start to save your setting.
To turn Extra Dry Heat ON or OFF:
1
Follow the above instructions to enter options mode.
2
With the display showing "d:00" or "d:01" press the < button to turn Extra Dry Heat ON or OFF.
d:00 = Extra Dry Heat is OFF
d:01 = Extra Dry Heat is ON
3
Press Start to save your setting.
Auto Power Off
NOTE: Setting can only be changed for models with a display. For models without a display, the default setting is P:00
To save energy, the dishwasher is turned off 1 minute after the wash cycle ends. This setting can be adjusted from P:00 to P:02.
To change the setting:
1
Open the door and press the [On/Off] button.
2
Hold down the "A" button (see page 17)and press [Start] until the display indicates "d:0x" (x can be any number). Release both buttons.
3
Press the "A" button until the display indicates "P:0x".
4
Press the "C" button until the display corresponds with your requirements.
P:00 = dishwasher does not turn off automatically
P:01 = dishwasher turns off automatically after 1 minute
P:02 = dishwasher turns off automatically after 120 minutes (2 hours)
5
Press [Start] to save the setting.
For Models without Display
T
o enter options mode:
1
Press the On/Off button to turn the unit on. For models with the buttons on top, the door must be open. For models with the buttons on the
front, the door mustbe closed.
2
One of the wash cycle LEDs will be flashing.
3
Press and hold down the > button, then simultaneously press and release the Start
button. Now release the > button.
4
The "Clean" and one other LED (varies by model) will be flashing. You are now in options mode.
5
Press the > button to select the option you would like to adjust.
To set amount of Rinse Aid:
NOTE: If your glasses have spots on them, you need more rinse aid. If your glasses have streaks on them, you need less rinse aid.
1
Follow the above instructions to enter options mode.
2
With the "Clean" and "Rinse Aid" LEDs flashing, press the < button to change the amount of rinse aid dispensed. The "Clean" and "Rinse Aid" LEDs keep
flashing and:
0 wash cycle LEDs on = rinse aid is OFF
1 wash cycle LED on = lowest amount of rinse aid dispensed
2 wash cycle LEDs on = medium amount of rinse aid dispensed
3 wash cycle LEDs on = highest amount of rinse aid dispensed
3
Press Start to save your setting.
To turn Extra Dry Heat ON or OFF:
1
Follow the above instructions to enter options mode.
2
With the "Clean" and "Sanitized" LEDs flashing, press the < button to turn Extra Dry Heat ON or OFF. The "Clean" and "Sanitized" LEDs keep flash-
ing and:
0 wash cycle LEDs on = Extra Dry Heat is OFF
1 wash cycle LED on = Extra Dry Heat is ON
3
Press Start to save your setting.
14