Table of Contents
Advertisement
ENGLISH
(Original instructions)
Inspection and repairs
Before use, check the appliance for
u
damaged or defective parts. Check for
breakage of parts, damage to switches
and any other conditions that may
affect its operation.
Do not use the appliance if any part is
u
damaged or defective.
Have any damaged or defective parts
u
repaired or replaced by an authorized
repair agent.
Regularly check the power lead and
u
connector for damage. If the supply
cord or connector is damaged, it must
be replaced by the manufacturer or an
authorised BLACK+DECKER Service
Centre in order to avoid a hazard.
Never attempt to remove or replace
u
any parts other than those specified in
this manual.
Additional safety instructions
After use
Unplug the charger before cleaning.
u
When not in use, the appliance should be stored in a dry
u
place.
Children should not have access to stored appliances.
u
Residual risks
Additional residual risks may arise when using the tool which
may not be included in the enclosed safety warnings. These
risks can arise from misuse, prolonged use etc.
Even with the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks can not be avoided. These include:
Injuries caused by touching any rotating/moving parts.
u
Injuries caused when changing any parts, blades or ac-
u
cessories.
4
Injuries caused by prolonged use of a tool. When using
u
any tool for prolonged periods ensure you take regular
breaks.
Impairment of hearing.
u
Health hazards caused by breathing dust developed when
u
using your tool (example:- working with wood, especially
oak, beech and MDF.)
Electrical safety
The appliance is designed for use with 12 V negative ground
vehicle battery systems.
Warning! The cigarette lighter connector is fitted with a non-
serviceable safety fuse. The fuse may operate in the event of
a fault. If this occurs the fuse must be replaced together with
the connector and cable by the manufacturer or an authorised
BLACK+DECKER Service Centre in order to avoid a hazard.
Warning! Do not operate the appliance with systems which
have positive ground or a different voltage.
The appliance is only to be used with the power supply
u
unit provided with the appliance.
The appliance must only be supplied at safety extra low
u
voltage corresponding to the marking on the appliance.
Symbols on the appliance
Read all of this manual carefully before using the
appliance.
Features
This tool includes some or all of the following features.
1. On/off switch
2. Bowl release button
3. Dust bowl
4. Nozzle
5. 12V car connector
Fig. A
6. Large brush head
7. Large crevice tool
8. Flexible hose
Assembly
Accessories (fig. A)
These models may be supplied with some of the following
accessories:
Large brush head (6)
u
Large crevice tool (7)
u
Flexible hose (8)
u
Fitting the accessories (Fig. A)
Fit the appropriate accessory on to the short end of the
u
flexible hose (8). Make sure that the accessory is pushed
fully on.
Fit the long end of the flexible hose (8) into the front of the
u
appliance. Make sure that the flexible hose is pushed fully
in.
Use
Connecting to the vehicle's power supply
Make sure that the appliance is switched off.
u
Remove the cigarette lighter from it's socket.
u
Plug the 12V car connector (5) into the cigarette lighter
u
socket.
Switching on and off (fig. B)
To switch the appliance on, slide the on/off switch (1)
u
forward to position 1.
To switch the appliance off, slide the on/off switch (1) back
u
to position 0.
Optimising the suction force
In order to keep the suction force optimised, the filters must be
cleared regularly during use.
Emptying and cleaning the product.
Quick empty the dust bowl (fig. C)
Press the release latches (9) and pull the nozzle (4)
u
straight off.
Empty the contents of the bowl.
u
To replace the nozzle, place it back onto the handle until it
u
"clicks" firmly into position.
Removing the dust bowl and filters (fig. D)
Warning! The filters are re-usable and should be cleaned
regularly.
Press the release latch (2) and pull the dust bowl (3)
u
straight off.
While holding the dust bowl over a bin, pull out the filter to
u
empty the contents of the bowl.
To replace the dust bowl, place it back onto the handle
u
until it "clicks" firmly into position.
Warning! Never use the appliance without the filters. Opti-
mum dust collection will only be achieved with clean filters.
Pre-filter (fig. E)
The Filter and pre-filter can be separated to allow better
cleaning.
(Original instructions)
ENGLISH
Twist the pre-filter (10) in a clockwise direction and lift
u
from the filter (11).
Cleaning the dust bowls and filters
The dust bowls and filters can be washed in warm soapy
u
water.
Make sure that the filters and the dust bowl are dry before
u
re-fitting.
Replacing the filters
The filters should be replaced every 6 to 9 months and when-
ever worn or damaged.
Replacement filters are available from your BLACK+DECKER
dealer:
For models: ADV1200 use filter part number VF110FC-XJ
Maintenance
Your BLACK+DECKER corded/cordless appliance/tool has
been designed to operate over a long period of time with a
minimum of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.
Warning! Before performing any maintenance on corded/
cordless power tools:
Switch off and unplug the appliance/tool.
u
Protecting the environment
Z
Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your BLACK+DECKER product
needs replacement, or if it is of no further use to you, do not
dispose of it with household waste. Make this product avail-
z
able for separate collection.
Separate collection of used products and packaging
allows materials to be recycled and used again.
Re-use of recycled materials helps prevent environ-
mental pollution and reduces the demand for raw
materials.
Local regulations may provide for separate collection of elec-
trical products from the household, at municipal waste sites or
by the retailer when you purchase a new product.
BLACK+DECKER provides a facility for the collection and re-
cycling of BLACK+DECKER products once they have reached
the end of their working life. To take advantage of this service
please return your product to any authorised repair agent who
will collect them on our behalf.
5
Advertisement
Table of Contents
