Spanish Quick Use Guide is included. Guía para rápida consulta en español está incluida. For USA assistance, please call: 1-800-211-PANA(7262) or, contact us via the web at: http://www.panasonic.com/contactinfo For Canadian assistance, please call: 1-800-561-5505 or visit us at www.panasonic.ca Operating Instructions...
Things You Should Know Thank you for choosing Panasonic! You have purchased one of the most sophisticated and reliable products on the market today. Used properly, we’re sure it will bring you and your family years of enjoyment. Please take time to fill in the information on the right.
Page 3
Model No.: HDC-HS9P Responsible party: Panasonic Corporation of North America One Panasonic Way, Secaucus, NJ 07094 Support Contact: Panasonic Consumer Electronics Company 1-800-211-PANA (7262) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Page 4
Batteries Battery pack (Lithium ion battery pack) ≥ Use the specified unit to recharge the battery pack. ≥ Do not use the battery pack with equipment other than the specified unit. ≥ Do not get dirt, sand, liquids, or other foreign matter on the terminals. ≥...
IMPORTANT SAFETY INSTRUCTIONS Read these operating instructions carefully before using the unit. Follow the safety instructions on the unit and the applicable safety instructions listed below. Keep these operating instructions handy for future reference. 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings.
Page 6
Precautions USE & LOCATION WARNING ≥ TO AVOID SHOCK HAZARD ... Your camera and power supply should not be exposed to rain or moisture. Do not connect the power supply or operate your camera if it gets wet. Your camera has been designed for outdoor use, however it is not designed to sustain direct exposure to water, rain, sleet, snow, sand, dust, or a direct splashing from a pool or...
Page 7
IMPORTANT ∫ Carefully observe copyright laws Whatever you have recorded and created can be used for your personal entertainment only. Under copyright laws, other materials cannot be used without obtaining permission from the holders of the copyrights. ∫ Cards that you can use with this unit SD Memory Card and SDHC Memory Card ≥...
Contents Accessories ... 10 Features ... 11 Quick Guide ... 12 Preparation Before using [1] Handling of HDD (Hard disk drive) ... 16 [2] Parts identification and handling ... 17 Remote control ... 20 Setup [1] Power supply ... 22 Charging the battery ...
Page 9
Playback Playback [1] Motion picture playback ... 66 Playing back motion pictures by date... 69 Intelligent scene selection ... 70 Repeat playback... 70 Resuming the previous playback... 70 [2] Still picture playback... 71 Playing back still pictures by date... 73 Editing [1] Deleting scenes/still pictures ...
Accessories Check the accessories before using this unit. Battery pack VW-VBG130 AC adaptor VSK0697 AC cable K2CA2CA00025 DC cable K2GJYYC00001 Remote control N2QAEC000023 Button-type battery CR2025 VQT1N74 AV cable K2KC4CB00027 Component cable K2KZ9DB00004 USB cable K2KZ4CB00011 CD-ROM...
Features ∫ Very clear high definition pictures This unit can record detailed high definition images to an SD card or HDD (hard disk drive). A High definition images (1920k1080) Number of available scan lines 1080 High definition images ≥ High definition images have more than approximately 2 times the number of available scan lines and approximately 6 times the number of pixels compared with standard images.
Quick Guide ∫ Charging the battery Charging lamp [CHARGE] A Lights up: Charging Goes off: Charging completed Connect the AC cable to the AC adaptor and the AC outlet. Insert the battery into the battery charger by aligning the arrows. ∫...
∫ Help mode The help mode explains the operation icons displayed when the AUTO/MANUAL/FOCUS switch is set to AUTO in recording mode. ≥ Rotate the mode dial to select 1) Press the cursor button to display the icon. 2) Move the cursor button right to select [ 3) Move the cursor button up, left or right to select the desired icon.
∫ Motion picture playback 1) Rotate the mode dial to select 2) (When playing back from an SD card) ] (motion picture playback) B of Select [ ] (card playback) tab A with the cursor button. (When playing back from a HDD) ] (motion picture playback) D of Select [ ] (HDD playback) tab C with the cursor...
USB cable jExpose the unit to vibrations or shock Indemnity about recorded content Panasonic does not accept any responsibility for damages directly or indirectly due to any type of problems that result in loss of recording or edited content, and does not guarantee any content if recording or editing does not work properly.
Before using LCD monitor open part LCD monitor (l 34) Pull the LCD monitor out in the direction of the arrow with your fingers. ≥ It can open up to 90o. ≥ It can rotate up to 180o A towards the lens or 90o B towards the opposite direction.
Page 18
≥ To select the recording functions (l 49, 53) ≥ To adjust manually (l 61) ≥ Playback operations (l 66, 71) DC input terminal [DC IN 9.3V] (l 25) Battery holder (l 23) Battery release lever [BATTERY] (l 23) 10 HDMI mini connector [HDMI] (l 85, 87) 11 Disc copy button [DISC COPY] (l 93) 12 Power LCD Extra button [POWER LCD EXTRA] (l 34)
Page 19
24 25 26 27 28 24 Face detection button [ 25 PRE-REC button [PRE-REC] (l 42) 26 Photoshot button [ ] (l 43) 27 Zoom lever [W/T] (In recording mode) (l 46) Volume lever [sVOLr] (In playback mode) (l 67) 28 Speaker 29 Internal microphones (5.1 channel support)
≥ Keep the button-type battery out of reach of children to prevent swallowing. Replace battery with Panasonic PART NO. CR2025 only. Use of another battery may present a risk of fire or explosion. Caution: Battery may explode if mistreated.
∫ Remote control usable range A Remote control sensor Distance: Within approx. 5 m (16 feet) Angle: Approx. 10o up and 15o down, left, and right ≥ The remote control is intended for indoor operation. Outdoors or under strong light, the unit may not operate properly even within the usable ranges.
Inserting/removing the battery Open the LCD monitor and install the battery by inserting it in the direction shown in the figure. A Insert the battery until it clicks and locks. CAUTION Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer.
Charging and recording time ≥ Temperature: 25 oC (77 oF)/humidity: 60% ∫ Charging time Battery model number Supplied battery/ VW-VBG130 (optional) VW-VBG260 (optional) VW-VBG6 (optional) ∫ Recording time Battery model number Supplied battery/ VW-VBG130 (optional) VW-VBG260 (optional) VW-VBG6 (optional) * The battery pack holder kit VW-VH04 (optional) is necessary. ≥...
( ) will flash. ≥ The remaining battery capacity is displayed in minutes when using the Panasonic battery that you can use for this unit. It may take time to display the remaining battery capacity. The actual time can vary depending on your actual use.
Preparation of SD cards Motion picture recording We recommend using SD cards conforming to Class 4 or higher of the SD Speed Class Rating the following SD cards made by Panasonic for motion picture recording. Cannot be used. Cannot be guaranteed in operation.
Inserting/removing an SD card Caution: If the SD card is inserted or removed while the power is on, this unit may malfunction or the data recorded on the SD card may be lost. First, format the SD card if one which has been used on another device is going to be used for the first time on this unit.
Setup Rotate the mode dial to switch to HDD recording, card recording, playback or power OFF. Turn on the power by turning the mode dial to the lock release button A. The status indicator lights and the power turns on. ≥...
Setup Operate the displayed menu screens with the cursor button. Press the MENU button. MENU ≥ The menu displayed differs depending on the position of the mode dial. Select the top menu A and move the cursor button right or press the cursor button.
Language selection You can select the language on the screen display and the menu screen. Press the MENU button, then select [LANGUAGE] and press the cursor button. Select [English] and press the cursor button. Menu list HDD Recording mode/ ∫ [BASIC] [SCENE MODE] (l 61) [D.ZOOM] (l 46) [GUIDE LINES] (l 53)
[BEEP SOUND] This allows operations such as starting and ending recording to be signaled by a beep. 1 Beep When you start recording When you turn on the power When this unit is recognized by the PC or the printer, etc. 2 Beeps When you pause recording When you turn off the power...
Setup When the unit is turned on for the first time, a message asking you to set the date and time will appear. Select [YES] and perform steps 2 to 4 below to set the date and time. ¬ Rotate the mode dial to select Select the menu.
World time setting (Displaying the time of the travel destination) It is possible to display and record the time at the travel destination by selecting your home region and the travel destination. Select the menu. (l 29) [BASIC] # [SET WORLD TIME] # [YES] ≥...
Setup ≥ These settings will not affect the images actually recorded. Increasing the brightness of the LCD monitor Adjusting the brightness and the color level of the LCD monitor Select the menu. (l 29) [SETUP] # [LCD SET] # [YES] Select the item with the cursor button.
Recording (Basic) ∫ Basic camera positioning ≥ When you are outdoors, record pictures with the sunlight behind you. If the subject is backlit, it will become dark in the recording. ≥ When recording, make sure your footing is stable and there is no danger of colliding with another person or object.
About auto mode Color balance (white balance) and focusing are adjusted automatically. Depending on the brightness of the subject etc., the aperture and shutter speed are automatically adjusted for an optimum brightness. (The shutter speed is adjusted to a maximum of 1/250 in recording mode.) jAutomatic white balance (l 132) jAuto focus (l 132)
Recording (Basic) This unit records high definition images that are compatible with the AVCHD format on an SD card or HDD. Sound is recorded with the Dolby Digital 5.1 Creator. 0h00m00s 0h00m00s 0h00m00s HG 1920 R1h20m R1h20m R1h20m ≥ Rotate the mode dial while at the same time pressing in the lock release button A if changing from OFF to another mode.
Page 39
For some SD cards, the message appears suddenly, and recording stops. Use a Panasonic SD card or another SD card which can be used to record motion pictures. (l 26) When the unit stops while a usable SD card for recording motion pictures (l 26) is used, the data writing rate has deteriorated.
Recording modes/approximate recordable time Switch the picture quality of the motion pictures to be recorded. Select the menu. (l 29) [VIDEO] # [REC MODE] # desired setting Capacity SD card 1 GB 2 GB 4 GB 8 GB 16 GB 60 GB (1920k1080): Motion pictures can be recorded with the highest picture quality.
Quick start This unit will resume recording/pause mode about 0.6 seconds after the LCD monitor is reopened. ≥ When in quick start standby mode about 60% of the power used in recording pause mode is being consumed, so the recording time will be reduced. Select the menu.
PRE-REC This prevents you from missing a shot. This allows recording of the pictures and sound to start approximately 3 seconds before the recording start/stop button is pressed. Press the PRE-REC button. PRE-REC ] appears on the screen and the unit repeats the update by recording motion pictures for about 3 seconds onto the built-in memory and then deleting them.
Recording (Basic) The number of pixels recorded for still pictures is 1920k1080. Still pictures can also be recorded while recording motion pictures. ≥ Rotate the mode dial while at the same time pressing in the lock release button A if changing from OFF to another mode.
Page 44
To record still pictures clearly ≥ While recording motion pictures or during the PRE-REC operation, the following arrangements are applied so that motion picture recording takes preference over still picture recording. For vivid still pictures, we recommend pausing motion picture recording and taking still pictures after releasing the PRE-REC mode.
Picture quality Selecting the picture quality. Select the menu. (l 29) [PICTURE] # [PICT.QUALITY] # desired setting Still pictures with a high picture quality are recorded. Priority is given to the number of still pictures recorded. Still pictures are recorded in normal picture quality. ≥...
Recording (Basic) The maximum optical zoom ratio is 10k. ¬ Rotate the mode dial to select Zoom lever T side: Close-up recording (zoom in) W side: Wide-angle recording (zoom out) ≥ The zoom speed varies depending on the range over which the zoom lever is moved. ≥...
Recording (Basic) Reduces the image shaking (jitter) due to hand movement. ¬ Rotate the mode dial to select ≥ This function’s default setting is [ON]. ≥ In still picture recording mode, pressing the stabilizer function. (MEGA optical image stabilizer) ≥ When a tripod is used, we recommend that you turn the image stabilizer off. ≥...
Recording (Basic) When a subject is backlit and appears darker, this function detects the face and automatically adjusts the brightness and picture quality so that the face is recorded clearly. ¬ Rotate the mode dial to select In the face detection & AE mode, detected faces appear with frames.
Recording (Advanced) Select the operation icons to add different effects to the images to be recorded. ¬ Rotate the mode dial to select Press the cursor button, and icons will be displayed on the screen. ≥ The indication changes each time the cursor button is moved down.
Page 50
Low light ≥ The shaded operation icons are not displayed while recording. ≥ If you turn off the power or set the mode dial to self timer and tele macro functions are canceled. ≥ If you turn off the power, the fade function is canceled. Function Fade VIDEO...
Function Soft skin mode VIDEO PHOTO MagicPix VIDEO PHOTO Backlight compensation VIDEO PHOTO Low light VIDEO PHOTO Ø Self-timer PHOTO Tele macro VIDEO PHOTO Effect This makes skin colors appear softer for a more attractive appearance. This is more effective if you record a person closely from the torso up.
Page 52
Fade: ≥ The thumbnails of scenes recorded using fade in become black (or white). Intelligent contrast control: ≥ If there are extremely dark or bright parts or the brightness is insufficient, the effect may not be clear. Help mode: ≥ When the help mode is used, functions cannot be set.
Recording (Advanced) Menus Guide line, 24p digital cinema, Wind noise reduction, Microphone setup, Microphone level, HD hi-speed burst shooting, Built-in flash, Red eye reduction, Shutter sound, Zebra, Color bar, Auto slow shutter, Digital cinema color ¬ Rotate the mode dial to select ≥...
Function Wind noise reduction VIDEO Microphone setup VIDEO [SURROUND]: Sound is recorded with 5.1 ch surround microphone. [ZOOM MIC]: Directivity of the microphone is synchronized with the zoom operation. Sounds near the front of the unit are recorded more clearly if you zoom in (close-up) and surrounding sounds are recorded more realistically if...
Function Microphone level VIDEO AGC: Auto Gain Control [AUTO]: AGC is activated, and the recording level is adjusted automatically. [SETrAGC]: The desired recording level can be set. AGC will also be activated to reduce the amount of sound distortion. [SET]: AGC is not activated and so natural recording can be performed.
Page 56
Function HD hi-speed burst shooting PHOTO VQT1N74 Effect/Setting method 72 still pictures are recorded at a rate of 24 per second. Select the menu. (l 29) [PICTURE] # [HI-SPEED BURST] # [ON] Press the button. ≥ Up to 72 still pictures can be taken in burst mode. ([ red during recording.) Select the setting to save with the cursor button and press the cursor button.
Function Built-in flash PHOTO Red eye reduction PHOTO Effect/Setting method When the button is pressed, the flash is activated and the picture will be recorded. Use the built-in flash in order to record still pictures in dark places. Select the menu. (l 29) [PICTURE] # [FLASH] # [AUTO] or [ON] ≥...
Function Shutter sound PHOTO Zebra VIDEO PHOTO A Zebra pattern Color bar VIDEO PHOTO VQT1N74 Effect/Setting method You can add a shutter sound when recording still pictures. Select the menu. (l 29) [PICTURE] # [SHTR SOUND] # [ON] ≥ This function’s default setting is [ON]. Parts where white saturation (color saturation) is likely to occur (extremely brightly lit or shiny parts) are displayed with diagonal lines (zebra pattern).
Function Auto slow shutter VIDEO PHOTO Digital cinema color VIDEO 24p digital cinema: ≥ [Digital Cinema Color] is turned [ON] and is not changeable. ≥ Motion pictures recorded while this setting is turned to [ON] may not be played back properly with a player that does not support 24p.
Page 60
≥ Image quality is different from ordinary still picture recording. To record more vivid still pictures, turn off this function before recording. (l 43) ≥ If you turn off the power or set the mode dial to , this function is canceled. Built-in flash: ≥...
Recording (Advanced) ¬ Rotate the mode dial to select Set the AUTO/MANUAL/FOCUS switch to MANUAL. The icon shown in the illustration appears. Scene mode When you record images in different situations, this mode automatically sets optimum shutter speeds and apertures. Select the menu.
Portrait mode ≥ If this mode is used indoors, the screen may flicker. If so, change the scene mode setting to [OFF]. Manual focus adjustment If auto focusing is difficult due to the conditions, then use manual focus. ≥ Set the AUTO/MANUAL/FOCUS switch to MANUAL. (l 61) (When MF assist function is used) Select the menu.
White balance The automatic white balance function may not reproduce natural colors depending on the scenes or lighting conditions. If so, you can adjust the white balance manually. ≥ Set the AUTO/MANUAL/FOCUS switch to MANUAL. (l 61) Move the cursor button to select Select the white balance mode.
Manual shutter speed/aperture adjustment Shutter Speed: Adjust it when recording fast-moving subjects. Aperture: Adjust it when the screen is too bright or too dark. ≥ Set the AUTO/MANUAL/FOCUS switch to MANUAL. (l 61) Move the cursor button to select ] (aperture) or [ speed).
Page 65
Preparation Recording Playback Backup With a PC Others 66 Playback 74 Editing 82 With a TV VQT1N74...
Playback A Lock release button B Align with the mark. ≥ Rotate the mode dial while at the same time pressing in the lock release button if changing from OFF to another mode. Rotate the mode dial to select (When playing back from an SD card) Select [ ] (motion picture playback) of [...
Page 67
Select the scene to be played back and press the cursor button. G Thumbnail display H Previous page I Next page J Play mode select button K Scene number The selected scene is played back on the full screen, and the operation icon is automatically displayed on the screen.
∫ Fast forward/rewind playback Move the cursor button right during playback to fast forward. (Move the cursor button left to rewind.) ≥ The fast forward/rewind speed increases if you move the cursor button again. (The display on the screen changes from 5 to ≥...
Operating with the remote control Press the ; button. SEARCH PLAY SEARCH PAUSE STILL ADV STILL ADV SKIP STOP SKIP Press the E or D button. SEARCH PLAY SEARCH PAUSE STILL ADV STILL ADV SKIP STOP SKIP Motion picture compatibility ≥...
≥ Even if scenes are recorded on the same day, they are grouped separately in the following cases. jWhen the number of scenes exceeds 99 jWhen the SD card or HDD is repaired jWhen the setting of 24pDIGITAL CINEMA is changed jWhen the recording mode is changed from HA/HG/HX to HE...
Playback A Lock release button B Align with the mark. ≥ Rotate the mode dial while at the same time pressing in the lock release button if changing from OFF to another mode. Rotate the mode dial to select (When playing back from SD card) Select [ ] (still picture playback) of [...
Select the still picture to be played back and press the cursor button. G Play mode select button H Thumbnail display I Previous page J Next page K Still picture number L Folder/file name The selected still picture is played back on the full screen, and the operation icon is automatically displayed on the screen.
Playing back still pictures by date Still pictures recorded on the same day can be played back in succession. Select (By date), then press the cursor button. Select the playback date, then press the cursor button. The still pictures recorded on the date selected are displayed as thumbnails.
Editing Important: The deleted scenes/still pictures cannot be restored. ¬ Rotate the mode dial to select ∫ Deleting multiple scenes/still pictures from the thumbnail display Press the button while the thumbnail view screen is displayed. Move the cursor button to select [SELECT] or [ALL SCENES] and press the cursor button.
Page 75
≥ You can also delete scenes by pressing the MENU button, selecting [EDIT SCENE] # [DELETE] # [ALL SCENES] or [SELECT]. ≥ You can also delete still pictures by pressing the MENU button, selecting [PICT. SETUP] # [DELETE] # [ALL SCENES] or [SELECT]. ≥...
Editing To delete an unnecessary portion of a scene, first divide the scene and then delete the unnecessary portion. ¬ Select [ ] (motion picture playback) of [ is set to . (l 66) Select the menu. (l 29) [EDIT SCENE] # [DIVIDE] # [SET] Select the scene to be divided, then press the cursor button.
Editing Scenes/still pictures can be protected so that they are not deleted by mistake. (Even if you protect some scenes/still pictures on an SD card or HDD, formatting the SD card or HDD will delete them.) ¬ Rotate the mode dial to select Select the menu.
Editing You can write the data selecting still pictures to be printed and the number of prints (DPOF data) onto the SD card. ¬ Select [ ] (still picture playback) of [ (l 71) ∫ What is DPOF? DPOF (Digital Print Order Format) is a format which allows the user of a digital camera to define which captured images on the SD card are to be printed, together with information on the...
Editing Motion pictures and still pictures recorded with this unit can be copied between an SD card and HDD inserted in this unit. Copy after confirming remaining capacity on the copy destination. ≥ Display the used space or the usable space on the HDD on the information display (l 81) before copying to confirm that space is available on the copy destination.
Page 80
(Only when [SELECT DATE] is selected in step 3) Select the date to be copied and press the cursor button. ≥ When the cursor button is pressed again, the selected date will be canceled. ≥ Up to 99 dates can be set in succession. ≥...
Editing Formatting Please be aware that if an SD card or HDD is formatted, then all the data recorded on the SD card or HDD will be erased. Back up important data on a PC, DVD disc etc. ∫ Formatting SD cards ¬...
≥ Use the supplied component cable to connect the unit via the component terminal on your TV, while using the supplied AV cable to connect it to the video terminal. Use of the following Panasonic HDMI mini cables is recommended to connect the unit to the HDMI terminal.
Page 83
≥ Check that the plugs are inserted as far as they go. ≥ We recommend using Panasonic HDMI mini cables (optional). Part numbers: RP-CDHM15 (1.5 m/4.9 feet), RP-CDHM30 (3.0 m/9.8 feet) ≥ Do not use any other component cables except the supplied one.
Page 84
TV for details.) Refer to the following support site for information about the Panasonic TVs that you can directly insert an SD card into the SD card slot on the TV and then play it back.
HDMI compatible high definition TV and then play back the recorded high definition images, you can enjoy them in high resolution with high quality sound. If you connect this unit to a Panasonic TV compatible with VIERA Link, linked operations (VIERA Link) are possible. (l 87) Select the desired method of HDMI output when using an HDMI mini cable (optional).
≥ Please read the operating instructions for the AV amplifier, speakers and TV for more information about how to connect them etc. ≥ If you connect this unit to a Panasonic AV amplifier and Panasonic TV that are compatible with VIERA Link, linked operations (VIERA Link) become possible. (l 87) ≥...
EZ Sync ≥ This function allows you to use your remote control for the Panasonic TV for easy operations when this unit has been connected to an VIERA Link compatible device using a HDMI mini cable (optional) for automatic linked operations.
Page 88
VIERA Link, read the operating instructions for the devices. ≥ Available linked operations between this unit and a Panasonic TV is different depending on the types of Panasonic TVs even if they are compatible with VIERA Link. Refer to the operating instructions of the TV for the operations that support on the TV.
≥ Please read the operating instructions of the DVD burner for how to use it. Preparing for copying/playing back We recommend using Panasonic DVD burner VW-BN1. About discs that can be used for copying 12 cm discs (DVD-RAM, DVD-RW, DVD-R, DVD-R DL) ≥...
Insert the disc in the DVD burner. (When copying) Select [BURN DISC] and press the cursor button. (When playing back) Select [PLAY DISC] and press the cursor button. ≥ Refer to page 94 for how to play back the copied discs. Copying to discs ≥...
(Only when [SELECT DATE] is selected in step Select the date you want to copy and press the cursor button. ≥ When the cursor button is pressed again, the selected date will be canceled. ≥ Up to 99 dates can be selected in succession. ≥...
Page 93
About the approximate time it takes for copying to a disc To copy motion pictures to the full capacity of a disc Disc type DVD-RAM Approx. 50 min to 80 min DVD-RW Approx. 35 min to 75 min DVD-R Approx. 25 min to 45 min To copy 600 still pictures (approx.
Playing back the copied disc ≥ Only discs that have been copied by connecting this unit to the DVD burner or where motion pictures have been recorded in AVCHD format can be played back. It may not be possible to play back discs recorded on other devices.
Managing the copied disc (Formatting/Auto protect/Displaying disc information) ≥ Connect this unit to the DVD burner and then select [PLAY DISC]. (l 90) ∫ Formatting discs This is for initializing DVD-RAM and DVD-RW discs. ≥ Select [ ] tab. Please be aware that if a disc is formatted, then all the data recorded on the disc will be erased.
With other products Images played back on this unit can be dubbed onto a DVD recorder or video device. ≥ Images are dubbed in standard quality. ≥ Use the AC adaptor to free you from worrying about the battery running down. Connect this unit to a video device and then set the mode dial to Start playback on this unit.
With other products To print pictures by directly connecting this unit to the printer, use a printer compatible with PictBridge. (Read the operating instructions for the printer.) PictBridge is an industry standard from the Camera & Imaging Products Association (CIPA) for direct printing.
Page 98
≥ To cancel the setting, set the number of prints to [0]. ≥ Up to 8 files can be set in succession by repeating steps 4 and 5. Press the MENU button to display the PictBridge menus. MENU Select the date print setting on [DATE PRINT].
Before using Data type Copying data to a A Motion/Still pictures 1 Built-in HDD Writing data to media A Motion/Still pictures B Motion pictures Copying data between media C Motion pictures Motion 1 Built-in HDD picture Easy editing: Editing motion picture data copied on an HDD of a PC ≥...
Page 101
Important Notice ≥ Do not insert a disc recorded in AVCHD format with HD Writer 2.5E in a device that does not support the AVCHD format. In some cases the disc may get stuck in the device. The disc will not play back on devices that do not support the AVCHD format. ≥...
End User License Agreement Before opening the CD-ROM package, please read the following. You (“Licensee”) are granted a license for the Software defined in this End User Software Agreement (“Agreement”) on condition that you agree to the terms and conditions of this Agreement.
Before using ≥ Even if the system requirements mentioned in these operating instructions are fulfilled, some PCs cannot be used. ≥ A CD-ROM drive is necessary to install the supplied software applications. (A compatible DVD writer drive and media are necessary for writing to a DVD.) ≥...
Page 104
Necessary software Windows Vista: DirectX 10 Windows XP/2000: DirectX 9.0c ≥ If you install the software on a PC that is not compatible with Sound DirectSound Support Interface USB port [Hi-Speed USB (USB 2.0)] Other requirements Mouse or equivalent pointing device ≥...
Setup When installing the software, log on to your PC as the Administrator (or with a user name with equivalent authorization) or with the user name for a standard user account. (If you do not have authorization to do this, consult your manager.) ≥...
After the installation is complete, restrictions are displayed. Check the contents, then close the window. ∫ Uninstalling HD Writer 2.5E Follow the steps below to uninstall any software applications that you no longer require. Select [start] # ([Settings] #) [Control Panel] # [Add or Remove Programs (Applications)] or [Uninstall a program].
Setup After the software applications are installed, this unit must be connected to the PC and be correctly recognized by the PC. ≥ Remove the supplied CD-ROM from your PC. A USB cable (supplied) Connect this unit to the AC adaptor.
About the PC display When the unit is connected to a PC, it is recognized as an external drive. ≥ [Removable Disk] (Example: Example folder structure of an SD card: Removable Disk DCIM 100CDPFQ 101CDPFR MISC PRIVATE AVCHD AVCHDTN BDMV IISVPL We recommend using HD Writer 2.5E to copy or write back motion picture data recorded on...
(On the PC) Select [start] # [All Programs (Programs)] # [Panasonic] # [HD Writer 2.5E] # [HD Writer]. The HD Writer 2.5E introductory screen is displayed. If [OK] is clicked, the software will start.
Using with a ≥ HD Writer 2.5E is not available for Macintosh. ∫ Operating environment for the card reader function (mass storage) Macintosh Mac OS X 10.4 PowerPC G5 (1.8 GHz or higher) Intel Core Duo Intel Core Solo 64 MB or more Interface USB port ≥...
Indications ∫ Recording indications Motion picture recording 1920 0h00m00s HG R1h20m PRE-REC 1/100 OPEN JAN 1 2008 12:34PM 3000 MEGA M A Still picture recording (when the button is pressed) Remaining battery power (l 25) 90min Remaining battery time (l 25) R1h20m Remaining time for motion picture recording (l 39)
Intelligent contrast control (l 50) ± (White) Focus indication (l 43) ¥ (Green) Ø10, Ø2 Self-Timer recording (l 51) ß/ßA/ Flash (l 57) ßi/ßj Flash level (l 57) Red eye reduction (l 57) Still picture quality (l 45) Number of recording pixels for still pictures (l 45) 1920k1080 M...
Page 114
PictBridge When a printer compatible with PictBridge is connected (l 97) DPOF already set (to more than 1) (l 78) Protected still pictures (l 77) Number of recording pixels for still pictures (l 45) 1920k1080 M The picture size is not displayed for still pictures recorded with other products that have different picture sizes from the sizes shown above.
Messages Indications Major confirmation/error messages to be indicated on the LCD monitor in text. RECOMMEND DATA BACK UP PERIODICALLY. We recommend backing up important recorded motion pictures and still pictures periodically to a PC, DVD disc etc. to protect it. This message does not indicate that there is a problem with this unit. HDD BACKUP RECOMMENDED.
Page 116
≥ Use a battery that is compatible with this unit. (l 24) If using a Panasonic battery compatible with this unit, eject the battery and then insert it again. If the message appears even after repeating this several times, this unit needs repair. Detach the power and contact consumer support.
About recovery If faulty management information is found when the HDD or a SD card is accessed, one of the following messages may appear. Be sure to follow the messages. (Repairing may take time depending on the error.) CONTROL DATA ERROR HAS BEEN DETECTED.
Helpful hints Some functions in this unit are disabled or cannot be selected due to the unit’s specifications. The table below shows examples of functions restricted by various conditions. Functions Motion picture recording PRE-REC Zoom Digital zoom Face detection & AE mode Backlight compensation Intelligent contrast control Low light...
Page 119
Functions Flash Auto slow shutter Digital cinema color Scene mode MF assist function Change of white balance Adjusting the shutter speed, iris/gain Conditions which disable the functions ≥ While recording motion pictures ≥ When PRE-REC is used ≥ When the MagicPix function is used ≥...
Helpful hints Problem This unit cannot be turned on. This unit does not stay on long enough. Battery runs down quickly. This unit is turned off automatically. The minute display of the remaining battery power indication is not displayed correctly. VQT1N74 Troubleshooting ≥...
Page 121
Problem This unit cannot be operated though it is turned on. This unit does not operate normally. The remote control does not function. The remaining time indication or the elapsed time indication is not shown. Recording does not start although power is supplied to this unit and the SD card is correctly inserted.
Page 122
Problem Auto focus function does not work. Recorded still pictures are not clear. Some playback images are skipped automatically. Although this unit is correctly connected to a TV, images cannot be seen. The images are squeezed horizontally. Scenes cannot be deleted.
Page 123
Problem If the SD card is inserted in another device, it is not recognized. The indication disappears. The screen is frozen. No operation can be performed. White round spots like soap bubbles appear on the recorded picture. “PUSH THE RESET SWITCH.”...
Page 124
Problem VIERA Link does not work. When connected by the USB cable, this unit is not detected by the PC. When the USB cable is disconnected, an error message will appear on the PC. The power of the DVD burner cannot be turned Cannot see the PDF operating instructions for HD Writer 2.5E.
Page 125
∫ When the scenes were recorded on different dates A The image will be still for several seconds wherever the date changes. B The images are played back smoothly if the scenes were recorded on the same date. ∫ When more than 99 scenes were recorded on the same date A The image will be still for several seconds when the scene changes every time 99 recorded scenes have been played back.
∫ When the recording mode was changed from HA/HG/HX to HE or from HE to HA/HG/HX A The picture momentarily stops where the scenes switch between HA/HG/HX and HE modes. B Playback is smooth if the same mode is used or the mode is switched among HA, HG and HX. ∫...
Page 127
∫ Example 2: When recording again after having deleted the last scene. 1 Scene to be deleted 2 A new scene is recorded here. A The image will be still for several seconds wherever a scene was deleted. B The images of consecutive scenes where they are no deletions are played back smoothly one after another.
Page 128
∫ When editing scenes on a PC using a software such as HD Writer 2.5E ∫ Example 1: When scenes were selected using HD Writer 2.5E and output to the media If scenes were dragged and dropped from the scene display area A and output to the media, the images will be still for several seconds wherever one scene changes to the next.
Cautions for use About this unit The unit and the SD card become warm during use. This is not a malfunction. Keep the High Definition Video Camera as far away as possible from electromagnetic equipment (such as microwave ovens, TVs, video games etc.).
About the battery The battery used in this unit is a rechargeable lithium-ion battery. It is susceptible to humidity and temperature and the effect increases the more the temperature rises or falls. In cold areas, the full charge indication may not appear or the low battery indication may appear about 5 minutes after starting use.
LCD monitor ≥ When the LCD monitor gets dirty, wipe it with a dry soft cloth. ≥ In a place with drastic temperature changes, condensation may form on the LCD monitor. Wipe it with soft dry cloth. ≥ When the unit has become very cold, for example due to storage in a cold area, its LCD monitor will be slightly darker than usual immediately after the power is turned on.
Explanation of terms Automatic white balance White balance adjustment recognizes the color of light and adjusts so the white color will become a purer white. The unit determines the hue of light that comes through the lens, thereby judging the recording condition, and selects the closest hue setting.
Page 133
Recording a subject behind dirty or dusty window The subject behind the window will not be focused because the focus is on the dirty window. Similarly, when recording something on the opposite side of a road with heavy traffic, a vehicle that happens to pass by may be brought into focus.
Specifications High Definition Video Camera Information for your safety Power source: Power consumption: Signal system Recording format Image sensor Lens Filter diameter Zoom Monitor Microphone Speaker White balance adjustment Standard illumination Minimum required illumination A/V terminal video output level Component terminal video output level HDMI mini connector video output level...
Page 135
Flash Dimensions Mass (Weight) Mass (Weight) in operation Operating temperature Operating humidity Battery operation time Motion pictures Recording media Compression Recording mode and transfer rate Picture size Audio compression Reader/writer function: SD card: Read/Write (No copyright protection support) HDD: Read only Hi-Speed USB (USB 2.0), USB terminal Type Mini AB PictBridge-compliant Available range: Approx.
Page 136
Still pictures Recording media Compression Picture size AC adaptor Information for your safety Power source: Power consumption: DC output: Dimensions Mass (Weight) Specifications may change without prior notice. VQT1N74 SD Memory Card: 8 MB, 16 MB, 32 MB, 64 MB, 128 MB, 256 MB, 512 MB, 1 GB, 2 GB (FAT12 and FAT16 system corresponding) SDHC Memory Card: 4 GB, 8 GB, 16 GB (FAT32 system corresponding)
TO OBTAIN ANY OF OUR ACCESSORIES YOU CAN DO ANY OF CALL PANASONIC’S ACCESSORY ORDER LINE AT 1-800-332-5368 MAIL THIS ORDER TO: PANASONIC SERVICE AND TECHNOLOGY COMPANY ACCESSORY ORDER OFFICE In CANADA, please contact your local Panasonic dealer for more information on Accessories. VQT1N74 Price Each Your State &...
Request for Service Notice: Mail this completed form and your Proof of Purchase along with your unit to: Panasonic Camera and Digital Service Center • Please include your proof of purchase. (Failure to do so will delay your repair.) •...
If your product does not work properly because of a defect in materials or workmanship, Panasonic Consumer Electronics Company or Panasonic Puerto Rico, Inc. (collectively referred to as “the warrantor”) will, for the length of the period indicated on the chart below, which starts with the date of original purchase (“warranty period”), at its option either (a) repair your product with new or refurbished...
1-800-211-PANA (7262), Monday-Friday 9 am-9 pm; Saturday-Sunday 10 am-7 pm, EST For hearing or speech impaired TTY users, TTY : 1-877-833-8855 Purchase Parts, Accessories and Instruction Books online for all Panasonic Products by visiting our Web Site at: http://www.pstc.panasonic.com or, send your request by E-mail to: npcparts@us.panasonic.com...
5770 Ambler Drive, Mississauga, Ontario L4W 2T3 PANASONIC PRODUCT – LIMITED WARRANTY Panasonic Canada Inc. warrants this product to be free from defects in material and workmanship and agrees to remedy any such defect for a period as stated below from the date of original purchase.
Spanish Quick Use Guide/Guía española para el uso rápido ∫ Carga de la batería Luz indicadora de carga [CHARGE] A Encendida: Carga en curso Apagada: Carga completada Conecte el cable de CA al adaptador de CA y a la toma de CA. Instale la batería en el compartimiento alineando la marca y, a continuación, conéctela de forma segura.
Page 146
Coloque el selector del modo en OFF. Abra la tapa de la tarjeta SD mientras desplaza la palanca SD CARD OPEN B. Inserte/extraiga la tarjeta SD. ≥ Coloque el lado del terminal C en la dirección mostrada en la figura y empújelo hasta que tope manteniéndolo derecho.
Page 147
∫ Reproducción de películas 1) Gire el selector de modo para seleccionar 2) (Cuando reproduce la tarjeta SD) Seleccione [ ] (reproducción de películas) B de la ficha [ de tarjeta) A usando el botón cursor. (Cuando reproduce la HDD) Seleccione [ ] (reproducción de películas) D de la ficha [...
Page 148
Panasonic Consumer Electronics Company, Division of Panasonic Corporation of North America One Panasonic Way, Secaucus, NJ 07094 Panasonic Puerto Rico, Inc. Ave. 65 de Infantería, Km. 9.5, San Gabriel Industrial Park, Carolina, Puerto Rico 00985 Panasonic Canada Inc. 5770 Ambler Drive, Mississauga, Ontario, L4W 2T3...