(Performance Editor Define) - Korg Prophecy Basic Manual

32
4.5
Performance
Editor assignments
(Performance Editor Define)
For each program in Performance mode, you can assign program parameters to knobs 1-5 for realtime
control of the sound. For each program you can make four sets of Performance Editor settings. These
settings are made in Performance Editor Define. In the following pages, the explanation will continue
the procedure given in "4.2 Editing a program," using the program you initialized and then modified.
The initialized program has the following settings.
PE
PEl
PE2
PE3
PE4
KNOB No. Assign Parameter Knob Left Knob Right
Curve
KNOB1
OSC1 __ 0ctave
000% 100% LINER
KNOB2 Std1_Wave 000% 100% LINER
KNOB3 Stdl_FiampLevel 000% 100% Exp
KNOB4 Std1_ WaveForm 000% 100% Exp
KNOB5
Delay __ Balance
000% 70% Exp
KNOB1
OSC2 __ Octave
000% 100% LINER
KNOB2 Std2_Wave 000%
100% LINER
KNOB3 Std2_1RampLevel 000% 100% Exp
KNOB4 Std2_WaveForm 000% 100% Exp
KNOB5 Chorus_Balance 000%
70% Exp
KNOB1 Filter1_Fc
000% 100% LINER
KNOB2 Filter1_Resonance 000% 90% LOG
KNOB3 Filter1 FcEGint 000% 100% LINER
KNOB4 EG3_AttackTime 000%
100% LINER
KNOB5 EG3_1DecayTime 000%
100% LINER
KNOB1 Filter:!_FC 000%
100% LINER
KNOB2 Filter:!_Resonance 000%
90% LOG
KNOB3 Filter:!FcEGint 000%
100% LINER
KNOB4 EG3_StartLevel 000%
100% LINER
KNOB5 EG3_)l.ttackLevel 000%
100% LINER
From Performance mode, press the PE DEFINE key.
The PE DEFINE key LED will light, and you will enter Performance Editor Define. The PE key being
edited will blink.
~
Use the PAGE keys to move to PED-1 [PEl Definition]. Here you can specify the
parameters that will be controlled by each knob for PEl. Rotate knob 1 and check that
#1-#5 are set as shown in the PEl area of the above table.
These settings determine which parameters will be assigned to each knob when PEl key is pressed.
Rotate knob 2. Notice how the assigned parameter changes. Here you can select the
parameter that will be assigned to the knob.
The display shows an abbreviation of the parameter name that would be displayed fully in Edit
mode. For the correspondence between the abbreviation and the full parameter name, refer to the
"Performance Editor Assign List" in the appendix of the separate "Parameter Guide." The
percentages shown in brackets indicate the value relative to the range of the values that can be set in
Edit mode.
Rotate knob 3. This setting specifies the effect produced by moving the knob to the far left
position in Performance mode. Listen to the effect on the sound as you modify the value.
Knob 4 specifies the effect produced by moving the knob to the far right position in
Performance mode. Set the value in the same way. Use the CURSOR< key to return to
the Assign Parameter that you set in step
[ji .
Notice that the sound changes here as
well. This is because the assigned parameters have returned to the values of their
settings.
liD
The indication of "LINEAR" at the right allows you to select one of three curves that will
determine how the sound changes when you operate the knob selected in
~
.
This completes settings for PEl. Use the PAGE keys to move to PED-2-PED-4, and make settings for
PE2-PE4.