Fujitsu ARTG30LHTA Operating Manual page 32

Duct type
Hide thumbs Also See for ARTG30LHTA:
Table of Contents

Advertisement

Selecting zone to be named:
1. In "Zone user setting" screen, select [Zone name setting]
with the [Cursor button (Up/Down)]. When you press the
[Enter button], "Name setting (group)" screen is displayed.
As a setting example, Zone 1 to 8 are supposed to be
connected in following instructions.
Name setting ( zone )
Zone 1
Zone 2
Zone 3
Zone 4
Zone 5
Back:
Day/Night setting
If any names have been registered for the zones already,
the registered names are displayed instead of "---" on this
screen.
If more than 6 zones are connected, you will have an extra
page.
Any of following actions make the screen switches from
"Name setting (zone) [1/4]" to the extra setting screen.
• Pressing the [Cursor button (Right)] in "Name setting
(zone) [1/4]" screen.
• Pressing the [Cursor button (Down)] during the cursor
is set to the last zone name in "Name setting (zone)
[1/4]" screen.
Name setting ( zone )
Zone 6
Zone 7
Zone 8
Back:
Day/Night setting
2. Select the zone to be named with the [Cursor button (Up/
Down)], and press the [Enter button].
Selecting group to be named:
1. In "Name setting (zone)" screen, press the [Cursor button
(Right)]. "Name setting (group)" screen opens.
Name setting ( group )
Day
Night
Back:
Day/Night setting
If any names have been registered for the groups already,
the registered names are displayed instead of "---" on this
screen.
2. Select the group to be named with the [Cursor button (Up/
Down)], and press the [Enter button].
En-31
[
1/4
]
Mo 10:00
Setting:
[
2/4
]
Mo 10:00
Setting:
[
3/4
]
Mo 10:00
Setting:
Selecting room-temperature sensor to be named:
1. In "Name setting (group)" screen, press the [Cursor button
(Right)]. "Name setting (sensor)" screen opens.
Name setting ( sensor )
Indoor unit
Primary RC
Secondary RC
Optional 1
Optional 2
Back:
Day/Night setting
If any names have been registered for the sensors already,
the registered names are displayed instead of "---" on this
screen.
2. Select the sensor to be named with the [Cursor button (Up/
Down)], and press the [Enter button].
When you press the [Enter button] after selecting any of zone,
group, or sensor, "Name setting" screen opens.
As the setting example, name setting screen for "Zone 1" is
used in following instructions.
Name setting ( Zone 1 )
A B C D E F G H I J K L M N O P Q R
S T U V W X Y Z & ( )
0 1 2 3 4 5 6 7 8 9 -
Back
Space
Cancel:
Preset names
Enter desired name.
3
For entering the text of the name, there are following 3
screens.
• Capital
• Lower case
• Preset names
You can enter mixed text with "Capital", "Lower case",
and "Preset names", up to 12 characters.
When you press the [Screen switch button (Left/Right)]
during entering the text, the screen switches as follows.
Capital
Lower case
Capital:
You can select and enter desired capital letter.
In "Capital" screen, set the cursor to the target letter with the
[Cursor button], and press the [Enter button].
Selected letter is displayed in the text field.
Name setting ( Zone 1 )
A B C D E F G H I J K L M N O P Q R
S T U V W X Y Z & ( )
0 1 2 3 4 5 6 7 8 9 -
Back
Space
Cancel:
Preset names
[
]
4/4
Mo 10:00
Setting:
Mo 10:00
+ ; : . , / _
End
Enter:
Lower case
Preset names
Mo 10:00
+ ; : . , / _
End
Enter:
Lower case
Text field

Hide quick links:

Advertisement

Table of Contents
loading

Table of Contents