Panasonic WORKIO DP-8060 Operating Instructions Manual

Panasonic WORKIO DP-8060 Operating Instructions Manual

Digital imaging systems
Table of Contents

Advertisement

Operating Instructions
(For Basic Operations)
Digital Imaging Systems
DP-8060 / 8045 / 8035
Model No.
Before operating this machine, please carefully read this manual, and keep this
English
documentation in a safe place for future reference.
(Illustration shows optional accessories that may not be installed on your machine.)

Advertisement

Table of Contents
loading

Summary of Contents for Panasonic WORKIO DP-8060

  • Page 1 Operating Instructions (For Basic Operations) Digital Imaging Systems DP-8060 / 8045 / 8035 Model No. Before operating this machine, please carefully read this manual, and keep this English documentation in a safe place for future reference. (Illustration shows optional accessories that may not be installed on your machine.)
  • Page 2: Operating Instructions

    Operating Instructions The following Operating Instruction manuals are included with this machine. Please refer to the appropriate manual and keep all manuals in a safe place for future reference. If you lose a manual, contact an authorized Panasonic dealer. Accessories...
  • Page 3 Memo...
  • Page 4: Table Of Contents

    Table of Contents Product Overview ■ Operating Instructions ... ■ Safety Information ... ■ Precautions ... ■ Security Suggestions for Key Operators ... 12 ■ Outer/Inner View ... 14 ■ Control Panel ... 15 ■ Touch Panel Display ... 16 ●...
  • Page 5 ■ Replacing the Staple Cartridge ... 57 ■ Dispose of the Punch Hole Residue ... 62 ■ Replacing the Battery ... 64 Appendix ■ Specifications ... 65 ● DP-8060/8045/8035 (Copier) ... 65 ● i-ADF (Standard) ... 66 ● Printer Unit ... 66 ●...
  • Page 6: Safety Information

    Safety Information For Your Safety To prevent severe injury and loss of life, read this section carefully before using the Panasonic DP-8060/8045/8035 to ensure proper, and safe operation of your machine. ■ This section explains the Warnings and Cautions used in this Operating Instructions manual.
  • Page 7: Operating Safeguards

    Place the machine on a level and sturdy surface that can withstand a weight of 302 lb (DP-8060/ 8045) / 295 lb (DP-8035). If tilted, the machine may tip-over and cause injuries.
  • Page 8: Important Safety Instructions

    Safety Information For Your Safety Consumable Safeguards Never heat the drum cartridge, or scratch its surface. A heated or scratched drum can be hazardous to your health. Be sure to use the specified type of batteries only. Ensure that batteries are installed with correct polarity.
  • Page 9: Precautions

    USE OF CONTROLS, ADJUSTMENTS OR PERFORMANCE PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. ■ ■ ■ ■ ■ Caution Label (For DP-8060/8045) (For DP-8035) Precautions Manufacturer's Name and Address Factory ID Complies with FDA radiation...
  • Page 10: Illegal Copies

    Output Tray more often to avoid paper jams. ■ Use of other than genuine Panasonic supplies can damage the machine. This may void the warranty of the machine and supplies. Be sure to use only genuine Panasonic Toner designed for the machine.
  • Page 11 Ventilation ■ The machine should be installed in a well-ventilated area to minimize the ozone density in the air. Handling ■ Do not turn the Power Switch Off, or open the Front Cover during copying/printing. ■ Sleep/Shutdown Mode Notice ● The following functions will not work if the Sleep/Off Mode setting is set to the Shutdown mode.
  • Page 12: Security Suggestions For Key Operators

    Security Suggestions for Key Operators To maintain your machine’s highly-sensitive document data secure from unauthorized users, machine access must be restricted, managed, and controlled from the initial machine installation, network connection, network configuration, and setup of security functions. The designated Key Operators are instructed to perform the recommended security measures described below.
  • Page 13 Memo...
  • Page 14: Outer/Inner View

    Outer/Inner View Left Cover (Optional System Console) Exit Cover ● Power Switches Power Switch Main Power Switch (Automatic Document Feeder) Control Panel Sheet Bypass Front Cover Right Cover Paper Tray 1 Right Lower Cover Paper Tray 2 Toner Bottle Paper Tray 3 (Optional System Fuser Knob Console)
  • Page 15: Control Panel

    Control Panel Original Copy Size Size Keys Keys Icon Contents Copy Key To use the unit as a photocopier. Fax/Email Key To use the Facsimile/Internet Fax/Email function. Scan/File Key To use the Scan/File function. Print Key Sets the Print function. Energy Saver Key Saves power while the copier is not in use.
  • Page 16: Touch Panel Display

    Touch Panel Display ● The above image shows everything is lit at the same time. This is for illustration purposes only, the machine will never have all icons, lit, or flashing at the same time. Refer to pages 17 to 20 for details of each function's image. Input an Identification Code with the Keypad.
  • Page 17: Copy Function

    Copy Function Job Status Indicator Ex.: Copying 3 sets. The Indicator displays the progress of a job task as follows: 0/3 → 1/3 → 2/3 → 3/3 ● The above image shows everything is lit at the same time. This is for illustration purposes only, the machine will never have all icons, lit, or flashing at the same time.
  • Page 18: Fax (Option)/Internet Fax/Email Functions

    Touch Panel Display Fax (Option)/Internet Fax/Email Functions ■ ■ ■ ■ ■ Touch Panel Display Indications File type and Transmit type Resolution Your machine is preset to Fine resolution, which is suitable for most documents. Use Fine or Super Fine for detailed documents. Original Shows the type of original.
  • Page 19: Scan/File Functions

    Scan/File Functions ■ ■ ■ ■ ■ Touch Panel Display Indications Contents File Type Displays the scanning file type (TIFF or PDF). Resolution Your machine is preset to 300dpi resolution, which is suitable for most documents. Original Shows the type of original. Contrast Indication The scanning contrast densities which are set in the Mode Setting screen are displayed in 7 levels.
  • Page 20: Print Function

    Touch Panel Display Print Function ■ ■ ■ ■ ■ Touch Panel Display Indications MAIL BOX Tab Allows you to use the Security Print function to start the printing job. JOB CONTROL Tab Allows you to select OFF LINE, ON LINE, CANCEL PRINT, JOB QUEUE functions.
  • Page 21: Placing Originals (Copy)

    Placing Originals (Copy) ■ ■ ■ ■ ■ How to Place Originals ● On the ADF Set the originals up to the upper limit indicator. Upper Limit Indicator Upper Guide ADF Tray Original Guides Adjust to the original’s width Notice for ADF ●...
  • Page 22: Basic Copy Operation

    Basic Copy Operation Making a Copy Original and Copy size are automatically selected. NOTE ● If the power is turned OFF, turn ON the Main Power Switch, and then turn ON the Power Switch. ● During the copy operation and after making copies, the fan motor may start spinning. This is a normal operation and is used to cool down the copier.
  • Page 23 Select the required settings. Ex: Copy Contrast and Original Mode Adjust the Manual Contrast (7 levels) Select type of Original(s) Mainly Text Text and Photo combined Mainly Photo ● For other mode settings, refer to the Operating Instructions (For Copy & Function Parameters) ●...
  • Page 24: Printing From Pc

    Printing from PC Printing from Windows Applications ■ Operation Chart 1. Installing the Printer Driver software and setting up the Printer Driver. ● Refer to the Operating Instructions (For Setting Up) provided with another booklet. 2. If more than one printer is installed on your PC, select the Printer as installed in step 1.
  • Page 25: Network Scanner

    Network Scanner ■ Operation Chart 1. Installing the Panasonic Document Magagement System. ● The Quick Image Navigator and Communications Utility are required for Network Scanner function, refer to the Operating Instructions (For Setting Up) provided with another booklet. 2. Set up the Communications Utility software.
  • Page 26: Scanning The Document To Your Pc

    Press the Scan/File key. Select the destination (PC) for the scanned data. ● If the Panasonic Communications Utility software is not started on your PC, a destination is not shown on the Touch Panel Display. Select the Scanner mode setting.
  • Page 27: Selecting The Scanner Mode

    ■ ■ ■ ■ ■ Selecting the Scanner Mode See below See right column JOB BUILD AND SADF For scanning a thin original from the ADF. 2-SIDED ORIGINAL For scanning 2-sided original. Select Binding Position FILE TYPE AND NAME For changing Scanning File Type and/or File Name.
  • Page 28: Address Book (Facsimile)

    Address Book (Facsimile) ■ ■ ■ ■ ■ Creating an Address Book NOTE ● For details on how to edit a registered address, refer to Address Book in the Operating Instructions (For Facsimile and Internet Fax/Email Functions) on the provided CD-ROM. ●...
  • Page 29 Select whether you wish to add this Telephone Number to Favorites. To enter other Fax numbers: Repeat steps 5 to 8 To exit this setting mode: Press Reset Key. Reset Key memo:...
  • Page 30: Address Book (Internet Fax/Email)

    Address Book (Internet Fax/Email) ■ ■ ■ ■ ■ Creating an Address Book NOTE ● For details on how to edit a registered address, refer to Address Book in the Operating Instructions (For Facsimile and Internet Fax/Email Functions) on the provided CD-ROM. ●...
  • Page 31 Select whether you wish to add this email address to Favorites. To enter other Email addresses: Repeat steps 5 to 8 To exit this setting mode: Press Reset Key. Reset Key memo:...
  • Page 32: Placing Originals (Facsimile/Internet Fax/Email)

    Placing Originals (Facsimile/Internet Fax/Email) ■ ■ ■ ■ ■ How to Place Originals ● ● ● ● ● On the ADF/Platen (See page 21) ● ● ● ● ● Sending Non-Standard Size Originals When transmitting non-standard size original(s), the machine may perform Rotate Transmission automatically and not transmit the portion of the original that exceeds the standard size (“P”...
  • Page 33: Sending Originals (Facsimile)

    Sending Originals (Facsimile) Sending Scanned data via Facsimile Scan Place Original(s) on the ADF or Platen Glass. Face Up Up to 85 sheets* (20 lb/Letter) *70 Sheets : Invoice/Legal/Ledger ● When scanning from the ADF, read the Notice for ADF. (See page 21) Face Down Align with top left corner ●...
  • Page 34 Select either ADDRESS BOOK DIALING, or MANUAL NUMBER DIALING. For ADDRESS BOOK DIALING Telephone numbers should be registered in advance. (See pages 28-29) Memory Transmit STN(s):001 TO:PANASONIC 5551234 PANASONIC QUALITY DEPT Select the destination For MANUAL NUMBER DIALING Facsimile: Enter the telephone number with the Keypad, and then select "OK".
  • Page 35: Sending Originals (Internet Fax/Email)

    Sending Originals (Internet Fax/Email) Sending Scanned data via Internet Fax/Email Scan Place Original(s) on the ADF or Platen Glass. Face Up Up to 85 sheets* (20 lb/Letter) *70 Sheets : Invoice/Legal/Ledger ● When scanning from the ADF, read the Notice for ADF.
  • Page 36 MMM-dd-yyyy 15:00 Ready To Fax Original Set AFRICA AMERICA APOLLO ASIA BRAZIL Enter the Email address, and then select "OK". EX: abc@panasonic.com Enter Addr(TO) STN(s):000 Enter Station(s) abc@panasonic.com @panasonic.com @mgcs.co.jp @abc-net.wxy.com @host.pana.com ● Refer to How to use the Keyboard, in the Address Book section.
  • Page 37: Receiving An Email From Pop Server

    Receiving an Email from POP Server Receiving Email Automatically With “147 Auto POP Receive” set to “Valid” and POP acquisition interval set between 1 and 60 minutes in Fax Parameters (refer to the Operating Instructions (For Facsimile and Internet Fax/Email Functions)), queries are transmitted to the POP Server periodically to check for new mail.
  • Page 38: Troubleshooting

    Troubleshooting Check Unit Does Not Operate Does the display light? Does the Energy Saver key flash (or light) and displays are turned OFF? Does any of the U## codes and messages appear on the display? (U1, U4, U6, U7, U11...etc.) Does the Add Staples indicator and message appear on the display? Does the Add Paper indicator and message...
  • Page 39: Machine Care

    Check Marked Copies Is the copier Platen Glass or Platen Sheet dirty? Is the original an OHP film, or a dark original? ■ If the measures outlined above do not solve the problem, call your Service provider. Machine Care ■ As a rule, clean weekly. Platen Sheet Action Clean the Platen Glass or Sheet.
  • Page 40: User (U) / Error Codes

    User (U) / Error Codes ■ ■ ■ ■ ■ User Error Codes (U Codes) U4, U12 U31, U33, U34 Code Check Points Front Cover is open. Finisher is separated from the machine. Right Cover is open. Right Lower Cover is open. Left Cover is open.
  • Page 41: Removing Misfed Paper

    If other locations indicate presence of paper, remove them and check the display again. ● If an unknown error code appears, or cannot clear the error codes, switch off the machine and contact the authorized Panasonic dealer. Check Points...
  • Page 42: System Console (Option) (A)

    Removing Misfed Paper ■ ■ ■ ■ ■ System Console (Option) (A) Right Lower Cover Misfed Paper Pull Open Open Remove Remove Close Right Lower Cover Close...
  • Page 43: Paper Entry Area (B)

    ■ ■ ■ ■ ■ Paper Entry Area (B) Right Cover Open Misfed Paper Remove Remove Pull Close Right Cover Close...
  • Page 44: Paper Transport Area (C)

    Removing Misfed Paper ■ ■ ■ ■ ■ Paper Transport Area (C) Open Transport Release Lever (Green) Remove Turn Paper Transport Knob (Green) Turn until it stops Close...
  • Page 45: Paper Exit/Fuser Area (D)

    ■ ■ ■ ■ ■ Paper Exit/Fuser Area (D) Open Open Exit Cover Fuser Knob (Green) Magnet Heat Roller Cover Remove Caution heated surface Magnet Heat Roller Cover Close Exit Cover Close...
  • Page 46: Automatic Duplex Unit (Adu) (E)

    Removing Misfed Paper ■ ■ ■ ■ ■ Automatic Duplex Unit (ADU) (E) Open Transport Release Lever (Green) Pull Automatic Duplex Unit Green Knob 5 (Center) Green Knob 5 (Left) Turn Green Knob 5 (Right) Push Automatic Duplex Unit Turn until it stops Close...
  • Page 47: Reverse Area (F)

    ■ ■ ■ ■ ■ Reverse Area (F) Open Left Cover Remove Close Left Cover ■ ■ ■ ■ ■ 3000-Sheet Tray (LCT) (Option) (G) When the optional 3000- Sheet Tray (LCT) (DA- MA301) is installed. Misfed Paper Latch Hold the latch and slide the large capacity paper tray to the right.
  • Page 48: 2-Bin Finisher (Option) (H)

    Removing Misfed Paper ■ ■ ■ ■ ■ 2-Bin Finisher (Option) (H) Remove Finisher Push Release button Punch Cover Open Turn to Mark When the optional 2- Finisher (DA- FS600/605) is installed. Misfed Paper Misfed Paper Punch Cover Open Finisher Upper Cover Transport Cover Misfed Paper...
  • Page 49: 2-Bin Finisher (Option) (H) (Da-Fs330)

    ■ ■ ■ ■ ■ 2-Bin Finisher (Option) (H) When the optional 2- Bin Finisher (DA-FS330) is installed. Upper Cover Misfed Paper Release Button Slide out Pull out Knob A Misfed Paper Finisher Guide Remove ● When paper cannot be removed: Remove Knob B Raise...
  • Page 50: 1-Bin Saddle-Stitch Finisher (Option) (H)

    Removing Misfed Paper ■ ■ ■ ■ ■ 1-Bin Saddle-Stitch Finisher (Option) (H) Remove Slide out Upper Cover Upper Cover When the optional 1-Bin Saddle-Stitch Finisher (DA-FS355A) is installed. Misfed Paper Release Button Finisher Remove Return Return Finisher...
  • Page 51: 2-Bin Saddle-Stitch Finisher Only (Option) (I)

    ■ ■ ■ ■ ■ 2-Bin Saddle-Stitch Finisher only (Option) (I) When the optional 2-Bin Saddle-Stitch Finisher (DA- FS605) is installed. Finisher Push Release button Open Lower Front Cover Turn Push and Turn SaddleExit Cover Open Misfed Paper Misfed Paper Infeed Cover Infeed...
  • Page 52: 1-Bin Saddle-Stitch Finisher (Option) (I/F)

    Removing Misfed Paper ■ ■ ■ ■ ■ 1-Bin Saddle-Stitch Finisher (Option) (I/F) When the optional 1-Bin Saddle-Stitch Finisher (DA- FS355A) is installed. (See page 50) Open Finisher Front Cover Lower Knob (Green) Remove Close Finisher Front Cover Turn Stitch Tray Release Button Slide Finisher...
  • Page 53: I-Adf (J)

    ■ ■ ■ ■ ■ i-ADF (J) ADF Cover Green Mark Inner Cover Misfed Paper ADF Tray Green Labelled Tab Exit Guide Misfed Paper Remove Exit Guide Paper Transport Knob ADF Cover Close...
  • Page 54: Adding Paper

    Adding Paper ■ ■ ■ ■ ■ Paper Tray (1550-Sheet Paper Tray 1) Open ● Paper Weight: 16-24 lb Max Level Indicator ● Paper Capacity: 1550 Sheets (20 lb) Close ■ ■ ■ ■ ■ System Console (550-Sheet Paper Tray 2-4) Open ●...
  • Page 55 ■ ■ ■ ■ ■ Sheet Bypass Sheet Bypass ● Slide out the tray until it stops. ● Approximately up to 50 ● Letter size sheets/20 lb ● Paper Weight: 15-35 lb ● To add paper to the Sheet Bypass, remove the leftover paper from the tray, and align it with the added paper and load them together onto the tray.
  • Page 56: Replacing Toner Bottle

    ● For optimum copy quality, it is recommended that only Panasonic Brand toner is used in the copier. Store toner in a cool dark area with low humidity. Do not unseal the toner bottle unless you are ready to use it.
  • Page 57: Replacing The Staple Cartridge

    Replacing the Staple Cartridge When optional Finisher is installed, an Add Staple message will be shown on the display. Add Staples ■ ■ ■ ■ ■ 2-Bin Finisher (DA-FS330) Release Button Slide out Open Stapler Cover Stapler Unit Lock Lever Pull out Staple Cartridge Empty...
  • Page 58 Replacing the Staple Cartridge Return Check the staple operation by following steps 11 to 13. Place originals. Select "SORT/FINISH", and then select "STAPLE-SORT". Press the Start key. Jammed Staple ● When the Staple jams The following message will be displayed on the Touch Panel Display: “Can Not Complete Confirm Staple Unit”...
  • Page 59 Return Close Staple Cover Follow the steps 11 to 13 on page 58 to check the staple operation. Jammed Staple ● When the Staple jams The following message will be displayed on the Touch Panel Display: “Can Not Complete Confirm Staple Unit”...
  • Page 60 Replacing the Staple Cartridge Return Close Follow the steps 11 to 13 on page 58 to check the staple operation. ● When the Staple jams The following message will be displayed on the Touch Panel Display: “Can Not Complete Confirm Staple Unit”...
  • Page 61 New Staple Case Tape Remove Staple Cartridge Return Stapler Unit Return Close Finisher Front Cover Follow the steps 11 to 13 on page 58 to check the staple operation. ● When the Staple jams The following message will be displayed on the Touch Panel Display: “Can Not Complete Confirm Staple Unit”...
  • Page 62: Dispose Of The Punch Hole Residue

    Dispose of the Punch Hole Residue When the punch hole container is full, the punch hole crust indicator will be shown on the display. ■ ■ ■ ■ ■ DA-FS600/FS605 with optional Punch Unit (DA-SP31) Open Pull out Close ■ ■ ■ ■ ■ DA-FS355A with optional Punch Unit (DA-SP41) Release Button Slide out...
  • Page 63 Return Finisher ■ ■ ■ ■ ■ DA-FS330 Release Button Slide out Pull out Finisher Entry guide Trash Box Return...
  • Page 64: Replacing The Battery

    Replacing the Battery ■ ■ ■ ■ ■ Replacing the Battery The copier has an internal battery (Product No.: CR2032) which maintains the date and time. In the event, the battery requires replacement, the following message will be displayed. The service life of the battery is approximately 1 year under normal use. CAUTION ●...
  • Page 65: Specifications

    Maximum: 600 dpi Touch Panel Display Ledger - Invoice via Paper Tray Max. 0.2" (5 mm) DP-8060/8045 : Approx. 180 seconds (68 °F/20 °C) DP-8035 : Approx. 30 seconds (68 °F/20 °C) DP-8060 : Approx. 3.5 seconds DP-8045 : Approx. 4.5 seconds DP-8035 : Approx.
  • Page 66: I-Adf (Standard)

    17 - 28 lb (64 - 105 g/m )/2-sided Supplied from copier 23.6 x 23.0 x 5.9 in (600 x 583 x 151 mm) DP-8060: Up to 60 sheets/minute DP-8045: Up to 45 sheets/minute DP-8035: Up to 35 sheets/minute Max. 1200 x 600 dpi...
  • Page 67: For G3 Facsimile (Option) [Da-Fg600]

    For G3 Facsimile (Option) [DA-FG600] Compatibility ITU-T Group 3 Coding Scheme JBIG, MH, MR, MMR (Conforms to ITU-T Recommendations) Modem Type ITU-T V.34, V.17, V.29, V.27 ter and V.21 Modem Speed 2,400 - 33,600 bps Document Size Ledger/Legal/Letter/Letter-R/Invoice/Invoice-R Max : Platen Glass : 11" x 17" (Ledger) Min : Platen Glass : No Minimum Scanning Method Sheet Feeding with CCD type image sensor...
  • Page 68: 3000-Sheet Tray (Lct) (Da-Ma301)

    16 - 24 lb (60 - 90 g/m Maximum 3000 sheets x 20 lb (75 g/m Supplied from copier 11.7 x 17.5 x 19.9 in (295 x 445 x 505 mm) 33 lb (15 kg) DP-8060/8045/8035 Letter-R/Legal 20 lb (75 g/m Letter-R : Maximum 2500 sheets...
  • Page 69: 2-Bin Saddle-Stitch Finisher (Da-Fs605)

    Dimensions (W x D x H) 26.4 x 24.2 x 59.1 in (670 x 613 x 1500 mm) Weight 114 lb (52 kg) Applicable Models DP-8060/8045 Punch Unit (DA-SP31) [for DA-FS600/605] Paper Size Letter/Ledger : 3-hole / Letter-R/Legal : 2-hole Paper Weight...
  • Page 70: 1-Bin Saddle-Stitch Finisher (Da-Fs355A)

    Specifications 2-Bin Finisher (DA-FS330) (2/2) Punch Paper Size Paper Weight Electrical Requirements Dimensions (W x D x H) Weight Applicable Model 1-Bin Saddle-Stitch Finisher (DA-FS355A) Mode Stitch Tray Paper Size Stitch Tray Paper Weight Paper CapacityBin Stitch Tray Staple Paper Size Paper Weight Capacity Point...
  • Page 71: Option And Supplies

    DA-MA301 3000 Sheet Paper Tray DA-FS600 For DP-8060/8045 DA-FS330 For DP-8035 DA-FS605 For DP-8060/8045 DA-FS355A For DP-8045/8035 DA-SP31 DA-FS600/FS605 for DP-8060/8045 DA-SP41 DA-FS355A for DP-8045/8035 DA-XT600 For DP-8060/8045/8035 DA-TK31 For DA-MA301 DA-SM16B For Electronic Sorting DA-SM64B For Electronic Sorting DA-SM28B...
  • Page 72: Multi-Tasking Job Table

    Multi-Tasking Job Table Current Job Copy 2nd Job Copy Copy Concurrent Copy* Storing Document Printing Network Scanning Storing Document GDI/PCL/PS Printing Receiving Data Printing Receive Document Facsimile (Sending) Storing Document Memory Transmission Facsimile (Receiving) Memory Receiving Printing Received Memory Data : Accepts and executes 2nd Job.
  • Page 73: Fcc Notice

    1-800-225-5329 (see Note below) Email: consumerproducts@panasonic.com Note: For Technical Support, please contact your Authorized Panasonic selling dealer. This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On the rear panel of this equipment is a label that contains, among other information, a product identifier in the format US:AAAEQ##TXXXX.
  • Page 74 FCC Notice If you experience trouble with this telephone equipment, please contact the manufacturer's authorized service agency for information on obtaining service or repairs. The telephone company may ask that you disconnect this equipment from the network until the problem has been corrected or until you are sure that the equipment is not malfunctioning.
  • Page 75 ■ ■ ■ ■ ■ For Users in Canada CAUTION Users should not attempt to make such connections themselves, but should contact the appropriate electric inspection authority, or electrician, as appropriate. Avertissement L’utilisateur ne doit pas tenter de faire ces raccordements lui-même; il doit avoir recours à un service d’inspection des installations électriques, ou à...
  • Page 76: Index

    Original Mode Select Buttons ... 17 Original Size (Copy) ... 21 Original Size (Facsimile/Internet Fax/Email) ... 32 Outer/Inner View ... 14 Panasonic Document Magagement System ... 25 Paper Tray Selection Button ... 17 Placing Originals (Copy) ... 21 Placing Originals (Facsimile/Internet Fax/Email) ... 32 Power Switch ...
  • Page 77 Receiving an Email from POP Server ... 37 Removing Misfed Paper ... 41–53 1-Bin Saddle-Stitch Finisher ... 50, 52 2-Bin Finisher ... 48–49 2-Bin Saddle-Stitch Finisher ... 51 3000-Sheet Tray (LCT) ... 47 Automatic Duplex Unit ... 46 i-ADF ... 53 Paper Entry Area ...
  • Page 78: Glossary

    Glossary Address Book Address Book Dialing (Automatic Document Feeder) CD-ROM Contrast (Document Distribution System) Dept. Code (Department Code) DHCP Disk Drive Drum Fax Board (Group 3) The Address Book is a convenient directory that stores contact Phone Numbers and Email Addresses for easy retrieval at a future time. A dialer that enables you to dial an entire Telephone Number/Email Address by pressing one key.
  • Page 79 The physical component of a PC which performs the basic operations on the (Hard Disk Drive) hard disk-including rotating the disk and reading/writing data to the disk. Install To add hardware or load a software application onto your multi-functional machine/computer. Internet The Internet is a vast collection of inter-connected networks that all use the TCP/ IP protocols, on which you can send an electronic email, chat to people...
  • Page 80 Glossary Protocol Resolution SD Card (Secure Digital Memory Card) Sleep Mode SMTP (Simple Mail Transfer Protocol) Software Station Name TCP/IP Thumbnails TIFF Toner Verification Stamp A standard process, a set of rules and conditions that perform a particular function. A word which is very common in PC and Internet Terminology. Ex: FTP (File Transmission Protocol), IP Address (Internet Protocol Address), TCP/IP (Transmission Control Protocol/Internet Protocol), POP (Post Office Protocol)
  • Page 81 Memo...
  • Page 82 Memo...
  • Page 83 The default functions can be adjusted depending on your office requirements. Please ask your authorized Panasonic dealer for more details. © 2006 Panasonic Communications Co., Ltd. All Rights Reserved. Unauthorized copying and distribution is a violation of law.
  • Page 84 PANASONIC MACHINE, INCLUDING BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. PANASONIC DIGITAL DOCUMENT COMPANY ASSUMES NO RISK AND SHALL NOT BE SUBJECT TO LIABILITY FOR ANY DAMAGE, INCLUDING, BUT NOT LIMITED TO DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LOSS OF PROFITS SUSTAINED BY THE CUSTOMER IN CONNECTION WITH THE USE OR APPLICATION OF THIS PANASONIC MACHINE.

This manual is also suitable for:

Workio dp-8035Workio dp-8045

Table of Contents