Take-Up Lever, Take-Up Head And Control Plate Guide; Capstan Brake Assembly; Sub Brake Assembly (Take-Up Side); Main Brake Assembly (Take-Up Side), Reel Disk (Take-Up Side) And Main Brake Assembly (Supply Side) - JVC HR-S9800U Service Manual

2.2.17 Take-up Lever, Take-up Head and Control Plate
Guide
(1) Remove the spring of the take-up lever from the main
deck.
(2) Remove the lug (A) of the take-up lever from the main
deck and pull out the take-up lever and the take-up head
together.
(3) Remove the screw (A).
(4) Align the idler arm assembly pin in the center (centre) of
the R section of the control plate guide, remove the con-
trol plate guide lugs (B) and (C) from the main deck, and
remove the control plate guide.
Idler arm assembly pin
Lug(C)
Screw(A)
Fig. 2-2-17a
2.2.18

Capstan Brake Assembly

1. How to remove
(1) Move the lug (A) of the capstan brake assembly in the
arrow-indicated direction so that it comes into alignment
with the notch of the main deck. (See Fig. 2-2-18a.)
(2) Remove the lug (B) of the capstan brake assembly from
the main deck and remove the capstan brake assembly.
Capstan brake assembly
Fig. 2-2-18a

2.2.19 Sub Brake Assembly (take-up side)

1. How to remove
(1) Remove the spring attached to the lid guide and sub
brake assembly (take-up side).
(2) Bring the lug (A) of the sub brake assembly (take-up side)
into alignment with the notch of the main deck.
(3) Remove the lugs (B) and (C) of the sub brake assembly
(take-up side) from the main deck and remove the sub
brake assembly (take-up side).
2-13
Take-up lever
Take-up head
Lug(A)
Lug(B)
Control plate guide
Lug(B)
Lug(A)
Lug(A)
Lug(B)
Fig. 2-2-19a
2.2.20 Main Brake Assembly (take-up side), Reel Disk
(take-up side) and Main Brake Assembly (sup-
ply side)
1. How to remove
(1) Move the main brake assembly (take-up side) in the ar-
row-indicated direction and remove the reel disk (take-
up side).
(2) Remove the spring attached to the main brake assembly.
(3) Remove the lug (A) of the main brake assembly (take-
up side) and pull out the lug (B) after bringing it into align-
ment with the main deck notch.
(4) Remove the lugs (C), (D) and (E) of the main brake as-
sembly (supply side) from the main deck and pull them
off. (See Fig.2-2-20a.)
(5) When installing the main brake assembly (take-up side),
slide the brake lever in the direction as indicated by the
arrow to prevent it from hitting the projection of the main
brake assembly (take-up side). (See Fig.2-2-20b.)
Main brake assembly Reel disk
(supply side)
(take-up side)
Lug(C) Lug(E) Spring
Lug(D)
Fig. 2-2-20a
( 1)
*
Brake
lever
Note:
• The parts with marked ( ) have different types of mechanisms (standard type
*
or high-speed FF/REW type).
* 1 : Uses the standard type mechanism only.
Fig. 2-2-20b
Spring
Sub brake
assembly
(take-up side)
Lug(C)
Main brake assembly
(take-up side)
Lug(B)
Notch
Lug(A)
Rotary encoder guide
Projection of the main
brake assembly
(take-up side)