Table of Contents
Advertisement
Quick Links
OWNER'S MANUAL
76CM/86CM WIDE SCREEN HDTV READY
MODEL: 76WSHDA
: 86WSHDA
Type Tested
Electrical
Safety
AS/NZS 3250 Lic 4166
Standards Australia
APP No: N18748
PALSONIC CORPORATION PTY LTD
1 JOYNTON AVENUE
WATERLOO NSW 2017 AUSTRALIA
TEL: (02) 9313 7111
FAX: (02) 9313 7555
www.palsonic.com.au
PALSONIC CUSTOMER SERVICE
TELEPHONE
AUSTRALIA: 1300 657 888
Advertisement
Table of Contents
Related Manuals for Palsonic 76WSHDA
Summary of Contents for Palsonic 76WSHDA
- Page 1 MODEL: 76WSHDA : 86WSHDA Type Tested Electrical Safety AS/NZS 3250 Lic 4166 Standards Australia APP No: N18748 PALSONIC CORPORATION PTY LTD 1 JOYNTON AVENUE WATERLOO NSW 2017 AUSTRALIA TEL: (02) 9313 7111 FAX: (02) 9313 7555 www.palsonic.com.au PALSONIC CUSTOMER SERVICE TELEPHONE...
-
Page 2: Table Of Contents
Congratulations on your purchase of Palsonic's HDTV ready. We recommend that you thoroughly read this manual before use to fully enjoy the many functions and excellent effects of this equipment. Retain this manual in an easily accessible location for future reference. -
Page 3: Cautions For Safety
Cautions for safety Cautions for safety When any unusual situation occurs, turn off the power supply at once and remove the plug from the wall outlet. Contact a qualified service department in your local area. Do not expose the TV set to rain or excessive moisture. - Page 4 Note: This set can operated on an AC power of 240V, 50Hz. You must not use a power supply of any other type. Do not cover the ventilating hole in the cabinet Keep a space of more than 10cm from the walls to the TV set to ensure adequate ventilation.
-
Page 5: Locations Of Controls
Location of controls Front view/Side view/Back view Front view Side view 1. TV/AV button: Open the signal source selection menu. 2. CH- button: Select a lower position number. 3. CH+ button: Select a higher position number. 4. MENU button: Enter into the menu. 5. - Page 6 Back view RF IN 1. Antenna input 2. DVD input terminals { VIDEO: Y, C 3. AV1 input terminals { S-VIDEO, VIDEO, AUDIO: L/MONO, R} 4. AV2 input terminals { S-VIDEO, VIDEO, AUDIO: L/MONO, R} 5. AV output terminals { VIDEO, AUDIO: L/MONO, R} 6.
-
Page 7: Remote Controller
Remote Controller Remote controller Power on/standby Still the current picture Channel up/down In menu operation used to move the cursor upward or downward. Text /image mode switch over Screen aspect ratio selection Retain on-screen display Sleep timer Surround sound control Direct channel selector One digit/two digit/three digit channel selector... -
Page 8: Battery Installation
Battery installation Open the battery compartment cover. Effective range of the Remote Install two "AAA" batteries, paying attention to the polarity diagram in the battery compartment. Notes: The battery life should be about one year under normal use. Do not try to recharge batteries not intended to be recharged. -
Page 9: Installation
Installation INSTALL the unit in a room where direct light will not fall upon the screen. Total darkness or a reflection on the picture screen may cause eyestrain. Soft and indirect lighting is recommended for comfortable viewing. Antenna connection/External equipment connections Antenna connection To ensure a bright-coloured and clear picture use an outdoor antenna or CATV cable. -
Page 10: External Equipment Connections
External Equipment Connections 1. To connect AV input terminals You can connect video equipments such as a VTR and video camera to this TV and enjoy the high quality picture and sound. If your video equipment has a S-VIDEO output terminal, connect it to the S-VIDEO input terminal (special S-VIDEO type) of the unit. - Page 11 Installation External equipment connections (continued) 2. To connect DVD input terminals The figure below shows how to connect the DVD input terminals of the TV set to the DVD Player, Laser Disk Player, etc. DVD Player, Laser Disk Player etc. COMPONENT AUDIO VIDEO OUTPUT...
- Page 12 4. To connect XGA input interface The figure below shows how to connect the set to the computer through XGA interface. THE SET'S REAR DVD IN Press AV/TV button to display the signal source selection menu and select XGA mode. At this time the screen will display information from the computer.
-
Page 13: Basic Operation
Basic Operations Turning on/off & Signal source selection Turning on Press the main POWER SWITCH, the red power indicator lights up, the set is in standby mode. Press the POWER button on the remote controller to turn on the set, and the power indicator turns to yellow. Or you can directly press Channel up/down button on the set to turn on the set. - Page 14 Menu introduction Menu introduction Press MENU to enter into menu mode. Press VOL or VOL to select menu icon. Press CH to enter into the menu. In menu operation, use CH to adjust. To exit menu mode, press MENU button. Below is a menu overview in RF (TV) mode.
-
Page 15: Operation In Rf Mode
Operations in RF mode Channel Presetting Auto search/Manual search If you have preset the channels, you can directly watch TV programs after turning on the set. If not, then preset channels in one of the following ways. Auto search Press MENU button. Press VOL or VOL to select... -
Page 16: The Setting Of Colour And Sound System
The setting of colour and sound system The setting of colour and sound system If the colour or sound of a certain channel is abnormal, the colour or sound system setting may be incorrect. Please do the following to change the system setting. (You may press OSD button to check whether the colour or sound system is correct) When the colour of the picture is abnormal Enter into PRESET menu. - Page 17 Channel Presetting Fine tuning When picture and sound's effect of a channel is poor (for example, one or two CATV channel's picture and sound are not standard), you can correct them by making use of Fine Tuning. AFC (Auto Frequency Control) Select the channel you want to fine-tune.
- Page 18 To skip unnecessary channels/VCR To skip unnecessary channels After presetting the channels, you can skip unnecessary channels so that only the channels you want to watch are selected with Channel up/down button. Select the channel you want to skip. Enter into PRESET menu. Press CH to select Skip menu item.
-
Page 19: Channel Selection
Channel Selection Channel selection Using the direct select buttons To select a one-digit channel Press -/-- button to display "-" on the top right screen. Press 0-9 number buttons to select a channel. To select a two-digit channel Press -/-- button to display "--" on the top right screen. Press 0-9 number buttons to select a channel. -
Page 20: Picture Adjustment
Picture adjustment Making use of PERSONAL button You can select the picture quality instantly among three preset modes and one user-set mode. Press the PERSONAL button to select the desired picture quality. Standard, Soft, Bright and Personal (user-set) can be selected cyclically. - Page 21 Picture adjustment Picture adjustment (continued) Picture Rotate When you switch on your TV, there may be a slight tilt of the picture to the left or right. This is due to the earth's magnetic field or position of your TV. To rectify, you can do the following. Enter into PICTURE menu.
- Page 22 To adjust Advanced menu item Enter into PICTURE menu. Press CH to select Advanced menu item. Press VOL or VOL to enter into the sub-menu. Press CH to select item. Press VOL or VOL to adjust. Option Function HEnhance Enhances horizontal details. Reduces picture noise.
- Page 23 Picture adjustment Picture adjustment (continued) Picture stillness Press STILL button to still the current picture, press it again to restore. Adjusting screen aspect Press PANORAMA button. Press CH to select a screen aspect ratio. 16:9/4:3/Panorama/Zoom can be selected. 16:9 mode expands the conventional 4:3 picture into a full 16:9 picture and at the same time still maintains the height of the picture.
-
Page 24: Sound Adjustment
Sound adjustment Volume adjustment Press the VOL or VOL to increase or decrease the volume. Sound mute Press MUTE button to mute the sound temporarily and press it again to restore the sound. Sound adjustment Press MENU button. Press VOL or VOL to select SOUND menu icon, press CH... - Page 25 Sound adjustment (continued) Sound adjustment Stereo function This set can identify stereo program. If you are receiving stereo program and you want to get stereo effect, please press STEREO button on the remote controller to select Stereo. Press the STEREO button again the set will restore to FM Mono mode.
-
Page 26: Timer Setting
Timer setting Making use of Sleep timer function You can make use of Sleep timer function to turn off the set automatically after a preset time, and bring the set to standby mode. Press SLP button, the screen will display Timer Off 00: 00: 00. -
Page 27: System Setup
System setup System setup To select the language for the OSD Use this function to switch the language for the OSD to either English or Chinese. Please do the following steps: Press MENU button. Press VOL or VOL to select PRESET menu icon, press CH enter into PRESET menu. - Page 28 Auto-Power-Off function With Auto-Power-Off function ON, the TV will automatically turn off after about 5 minutes when no signal is being received. Enter into OPTION sub-menu Press CH to select Auto Off menu item. Press VOL or VOL to change the Auto Off setting On or Off.
-
Page 29: Operation In Video Mode
Operation in Video mode (AV1/AV2/AV3/YCbCr) You can connect video equipments such as a VDC, VCR, DVD to this TV and enjoy the program play-backed by the video equipment. Press the AV/TV button to display the signal source selection menu and then select corresponding video mode. As regards to the menu operation and menu item adjustment in video mode, please refer to Operation in RF mode. -
Page 30: Operation In Hdtv Mode
Operations in HDTV mode When the signal source is input through YPbPr terminals, then the set will work in HDTV mode. Connect PDVD or HDTV set top box to the TV through YPbPr terminals. (Refer to Installation on page 10.) Firstly please press AV/TV button to call up the signal source selection menu and then select YPbPr mode. -
Page 31: Xga Mode
Operation in HDTV mode 2. XGA Mode Buttons' function When the signal source is input through XGA interface, then the set will work in HDTV mode. The XGA IN interface on this set can be used to connect to the following equipment: 1. -
Page 32: Osd Menu Overview
OSD menu introduction OSD menu overview Press MENU button The selected icon's colour will change and twinkle. SCREEN ADJUST PUSH TO MENU 3 5. 1 KHz EXIT V-SIZE 6500 9300 35. 1 KHz Fv: 5 6. 1 Hz H-SIZE EXIT EXIT 6500 6500K... - Page 33 OSD menu introduction & Operation examples OSD menu introduction (continued) CONTRAST BRIGHTNESS H-SIZE H-PHASE V-SIZE V-PHASE PIN-BALANCE PINCUSHION TRAPEZOID PARALLELOGRAM H-MOIRE V-MOIR ROTATION RECALL ENGLISH/CHINESE DEGAUSS 9300K 9300 6500K 6500 EXIT EXIT Notes: When the HD monitor gets signal from external equipment (such as Set top box, computer, DVD, etc.) through XGA interface, because of signal difference, the screen colour may not be in optimum state, this time, you can adjust colour.
- Page 34 Operation examples Contrast/brightness adjustment Press MENU button to call up the OSD main menu. Press CH button or CH move the cursor upward or downward and select (Contrast) or (The colour of the selected icon will change and glitter). Press MENU to enter into the sub-menu. Press CH or CH to adjust the level.
- Page 35 Operations examples (continued) Screen adjustment The screen adjustment includes H-SIZE, H-PHASE, V-SIZE, VPHASE, PIN-BALANCE, PINCUSHION, TRAPEZOID, PARALLELOGRAM, H-MOIRE, V-MOIRE, ROTATION, etc. Press MENU button to call up the main menu, press CH button to move the cursor to SCREEN ADJUST icon. Press MENU button again to enter into SCREEN ADJUST sub-menu.
-
Page 36: Display Mode Setting
In factory the set has been set with multi display modes which are frequently-used at present. With the development of digital processing technology, in the future there are external equipment with different display modes. If user discovers the input signal's display mode is different, while the horizontal and vertical frequency accords with the requirement of the set, the set can also support this display mode. -
Page 37: Troubleshooting Guide
Troubleshooting Guide Before calling service personnel, please check the following chart for a possible cause to the trouble you are experiencing. Symptoms The screen has no content, the power indicator is not lit up. The screen has no content, the power indicator is red. -
Page 38: Specifications
8W x 2 External control mode C bus control Surround sound Full function remote control 968 (W) x 564 (H) x 570 (D) (76WSHDA) Dimensions (mm) 1060 (W) x 660 (H) x 620 (D) (86WSHDA) Weight 66 kg (76WSHDA), 85kg (86WSHDA) -10°C ~ 50°C... - Page 39 PALSONIC CORPORATION PTY LTD 1 JOYNTON AVENUE WATERLOO NSW 2017 AUSTRALIA TEL: (02) 9313 7111 FAX: (02) 9313 7555 www.palsonic.com.au PALSONIC CUSTOMER SERVICE TELEPHONE AUSTRALIA: 1300 657 888 604-32613-02...