Congratulations on your purchase of this Palsonic colour television receiver. We recommend that you thoroughly read this manual before use to fully enjoy the many functions and excellent effects of this receiver. Retain this manual in an easily accessible location for future reference.
Hyperband 256 preset channels Automatic channel preset Intellectualized I C-bus control English/Chinese on-screen display Full function remote control AV input & output terminals Clock/Game/Calendar Four picture modes Four sound modes ON timer/OFF timer Surround sound Channel scan Channel edit Main features Introduction Features...
Introduction Important Safety Precautions Safety Precautions When any unusual situation occurs, turn off the power supply at once and remove the plug from the wall outlet. Contact a qualified service department in your local area. Do not expose the TV set to rain or excessive moisture.
Page 5
This TV set can operate on a power of ~240V, 50Hz. You must not use a power supply of any other type. Do not cover the ventilating hole in the cabinet Keep a space of more than 10cm from the walls to the TV set to ensure adequate ventilation.
Introduction Identification of Controls Front/Back view Front MENU AV/TV CH- Remote Sensor Back VIDEO AV2 input (VIDEO AUDIO: L/MONO, R) AV1 inputs (S-VIDEO, VIDEO, AUDIO: L/MONO, R) VIDEO L/MONO AUDIO Indicator Indicator VOL- VOL+ (2) DVD S-VIDEO MONITOR VIDEO L/MONO AUDIO AUDIO Power Switch...
Page 7
Sound mute Channel scan Recalling On-screen display Channel up/down Menu item select Sleep timer Channel edit MENU control buttons Game control buttons SLEEP EDIT SOUND GAME SYSTEM NOTES: In many cases, the function of are equal to the CH+/- buttons, and the function of VOL+/- buttons.
Introduction Installation Antenna connection/Battery installation Antenna connection Optimum reception of colour requires a good signal and will generally mean that an outdoor aerial must be used. The exact type and position of the aerial will depend upon your particular area. NOTES: It is recommended that the 75-ohm coaxial cable be used to eliminate interference and noise which may occur due to radio wave conditions.
Installing batteries Open the battery cover. Install two "AAA" batteries matching the +/- polarities of the battery to the +/- marks inside the battery compartment. Replace the battery cover. NOTES: Do not try to recharge batteries not intended to be recharged.
Page 10
Introduction External Equipment Connection (Please refer to the owner's manual of the equipment to be connected as well. External Equipment Connection To connect AV input terminals You can connect video equipment such as a VTR and video camera to this TV and enjoy the high quality picture and sound.
Page 11
To connect DVD input terminals The figure below shows how to connect the DVD input terminals of the TV set to the DVD Player, Laser Disc Player, etc. TV SET'S REAR (2) DVD S-VIDEO MONITOR VIDEO VIDEO L/MONO L/MONO AUDIO AUDIO AUDIO NOTES:...
Operations Turning on/off Turning on/off SLEEP EDIT SOUND GAME SYSTEM Turning on Press the Power Switch on the TV set, the red indicator lights up, the set is in standby mode. Press the button on the remote control and the TV set is turned on. In STANDBY mode, you can also press the Channel up button on the set to turn on.
SLEEP EDIT SOUND GAME SYSTEM Select input signal Watching AV program This TV set provides AV input terminals for your convenient connection to VCR, DVD or other video equipment. To watch video program from AV inputs, Press AV button repeatedly until you see the appropriate input indicator on the screen.
Operations Tuning in Auto search/Manual search/To skip unwanted channel SLEEP EDIT SOUND GAME SYSTEM If you have preset the channels, you can directly watch TV programs after turning on the set. If not, then preset channels in one of the following ways. Auto search Enter into TUNING menu.
Page 15
Press MENU button. Press VOL+/- to select TUNING icon. Press CH- to enter into TUNING menu. SLEEP EDIT SOUND GAME SYSTEM Press VOL+ to search towards higher frequency, the screen displays glittering " " press VOL- to search toward lower frequency, the screen displays glittering "...
Page 16
Operations Tuning in (continued) Fine tuning/The setting of colour and sound system SLEEP EDIT SOUND GAME SYSTEM Fine tuning Fine tuning is not necessary under normal conditions. However, in area of inferior broadcast conditions where adjustment is necessary for a better picture and sound, use Fine Tuning.
SLEEP EDIT SOUND GAME SYSTEM Channel selection Making use of direct select buttons Use direct selection buttons To select one-digit channel Method 1: press 0-9 button and wait for 2 seconds. Method 2: press 0 button twice, and then press the channel number.
Page 18
Operations Channel selection Making use of channel up/down buttons/Previous channel button/Channel scan/channel edit SLEEP EDIT SOUND GAME SYSTEM You can press DSP button twice to display the current time of the TV set, press again to cancel. (continued) Use Channel up/down buttons Press CH+ button, the channel number increases.
SLEEP EDIT SOUND GAME SYSTEM Picture adjustment To select the picture mode You can select the picture quality instantly among three modes and one user-set mode. Press the PIC button to select the desired picture quality. BRILLIANT, STANDARD, SOFTNESS and PERSONAL (user-set) can be selected cyclically.
Operations Sound adjustment Sound adjustment SLEEP EDIT SOUND GAME SYSTEM Adjusting volume Use VOL+ or VOL- button. Press VOL+ button, the volume increases; Press VOL- button, the volume decreases. (MUTE) button. If you want to mute the sound, press button on the remote control.
SLEEP EDIT SOUND GAME SYSTEM Adjusting sound Press MENU button. Press VOL+ or VOL- button to select SOUND icon. Press CH- to enter into SOUND menu. In SOUND menu press CH+/- to select desired item, press VOL+/- to adjust. Item VOL- BASS Weaker...
Operations System setup System setup SLEEP EDIT SOUND GAME SYSTEM Selecting OSD language Press MENU button. Press VOL+ or VOL- to select SETUP icon. Press CH- to enter into SETUP menu. Press CH+/- to select LANGUAGE. Press VOL+/- to select English or Chinese ( Menu demonstration Enter into SETUP menu.
Page 23
SLEEP EDIT SOUND GAME SYSTEM Setting Blue Background option Enter into SETUP menu. Press CH+/- to select B.B. Press VOL+/- to select On or Off. If the B.B is set to On, the TV set will display a blue background when there is no input signal. If the B.B is set to Off, the TV will display snowy picture when there is no input signal.
Operations Timer setting Clock/ON timer/OFF timer/Sleep timer SLEEP EDIT SOUND GAME SYSTEM You can press DSP button twice to display the current time of the TV set, press again to cancel. Setting clock Enter into TIMER menu. Press CH- to select CLOCK. Press VOL+ or VOL- to set the current time for the set.
Press MENU button. Press VOL+/- to select TIMER icon. Press CH- to enter into TIMER menu. SLEEP EDIT SOUND GAME SYSTEM PICTURE Setting OFF timer With the OFF timer. the TV will automatically switch to standby mode at a preset time. In TIMER menu, press CH+/- to select OFF TIMER.
Operations Playing games Playing games SLEEP EDIT SOUND GAME SYSTEM There are two built-in games for you to play: one is Falling cube, the other is Submarine. Making use of Falling cube Press GAME button once to enter into Falling cube game interface. Press any one of / / / buttons to start the game.
Before calling service personnel, please check the following chart for a possible cause to the trouble you are experiencing. Symptoms Power is not turned on Poor colour, poor tint Spots appear on the screen Stripes appear on the screen Double images or "ghosts" Snowy picture TV cabinet creaks Remote controller does...
Others Specifications Specifications Power Supply: ~240V, 50Hz Power Consumption: 140W Dimensions(mm): 760 (W) x 595 (H) x 490 (D) Weight(kg): CRT: 68cm TV system & channel range System PAL-B/G 2-12 Colour System: PAL-B/G NTSC (AV) Sound output: 6W x 2 Accessories: Remote controller X 1 Design and specifications are subject to change without notice.