Congratulations on your purchase of this Palsonic colour television receiver. We recommend that you thoroughly read this manual before use to fully enjoy the many functions and excellent effects of this receiver. Retain is manual in an easily accessible location for future reference.
This equipment has been designed and manufactured to meet the highest international standards, but, like any electrical apparatus which is operated at mains voltage, care must be taken if you are to obtain the best results and safety is to be assured. This is particularly important with audio and TV equipment.
TINT REMOTE SENSOR POWER INDICATOR 1. ANTENNA CONNECTIONS 1.1 Optimum colour reception requires a good antenna. An out-door antenna will be more effective to obtain a clear-picture. 1.2 Insert the out-door antenna into the antenna socket on the cabinet back. Adjust the direction or position of the outdoor antenna for the best possible picture.
3.1 STANDBY ( ) Button 3.1.1 Press STANDBY ( ) button to turn on the set (the indicator shows yellow) when the set is in STANDBY mode (the indicator shows red) , the channel position number is displayed in the screen. Press STANDBY ( the set is in OPERATION mode, and the indicator shows red.
Page 6
3.2.2.4 Press PRESET ON/OFF button to exit preset mode. The searched program station has been memorised at the present channel position, 3.2.2.5 Repeat 1~ 4 steps to search another channel. NOTE : * If the same channel position is selected during repeat operation, the former memory will be erased.
Page 7
CHANNEL INCREASE CHANNEL DECREASE (REMOTE) 3.5 VOLUME CONTROL 3.5.1. Press the VOL button to increase volume ; the green bar on the screen moves right. 3.5.2. Press the VOL button to decrease volume ; the green bar on the screen moves left. Display of minimum volume 3.6 AV/TV SELECTOR Press AV/TV button to change TV mode to AV mode when the set is in receiving (TV)
4. REMOTE CONTROL OPERATION: : STANDBY 1 ~ 9 : DIGITAL CHANNEL SELECTOR 10/0 : CHANNEL 10 OR CHANNEL 0 SELECTOR SYSTEM : COLOUR SYSTEM CONTROL -/- - : DIGIT OR TWO DIGIT CHANNEL SELECT : PREVIOUS 4.1 INSTALLING BATTERIES: 4.1.1 Remove the battery cover of Remote Control Unit.
4.3 CHANNEL SELECTION 4.3.1 Press CHANNEL SELECTOR ( decreased and displayed in the upper right corner of the screen. 4.3.2 Use the DIGITAL CHANNEL SELECTOR button for direct channel selection. 1) 1~10 channel Method 1: Press -/-- Example: To select channel 2 Press -/-- To select channel 10 Method 2:...
4.3.3 PREVIOUS BUTTON Pressing this button to select the channel that was tuned immediately before the one being watched. For example: If you are watching the program on channel 6, and the previous previous programme you watched was was on channel 15; then you can press the button to reach channel 15, press it again to return channel 6.
Page 11
4.6 Making use of PPS button (personal preference select) Press the PPS button, the screen will display the following five mode progressively: Press PPS The above five display modes corresponding analogue quantity is shown in the following chart: Analogue Display BRIGHTNESS mode llllll...
4.8 SLEEP BUTTON 4. 8. 1 Using SLEEP button allows you to have the appliance automatically turned off after a pre-determined time, and set the appliance to STAND BY mode. SLEEP 4. 8. 2 After the SLEEP function is set, the remaining time will be automatically displayed for 4 seconds every ten minutes.
Page 13
4.9.1 CLOCK 4.9.1.1 Press the TIMER button till "CLOCK" displays-on the screen. 4.9.1.2 Press the button to set the present hour. Press the button to set the present minute. 4.9.1.3 After setting the clock, press TIME SET button to start operating. Now the indication on the screen is green instead of red.
OFF TIME 0 : 00 4.9.8.8 Press TIME SET button, then the OFF TIME indication is green instead of red. OFF TIME function starts operating. 4.9.8.4 The appliance will be turned off when your setting time is up, and return to stand by mode.
5. INTERFACES This set has Audio & Video input and output sockets which allow direct connection to external equipments for playing back and recording the programs. 5.1. VIDEO PLAYBACK 5.1.1 The figure below shows how to connect the TV set to the video equipment. 5.1.2 Press the AV/TV button on the TV set or on the remote controller to select VIDEO mode, "VIDEO"...
Page 16
5. 3 DUBBING 5.3.1 The picture below shows how to connect TWO VCRs to the TV for dubbing one from the other. 5. 3. 2 Press AV/TV button of the TV set or on the remote control unit to select Video mode before dubbing, "VIDEO"...
6. TROUBLE SHOOTING GUIDE Many apparent malfunctions may be caused by slight misadjustment of regular controls or some other equally similar simple causes. If any problem arises in the operation of your set, first check through this list of symptoms and correction. Should the problem be unsettled, unplug the set and contact your dealer.