Lincoln Electric power wave c300 Operator's Manual
  1. Manuals
  2. Brands
  3. Lincoln Electric Manuals
  4. Welding System
  5. Power Wave C300
  6. Operator's manual

Lincoln Electric power wave c300 Operator's Manual

Hide thumbs Also See for power wave c300:
Table of Contents

Advertisement

Quick Links

RETURN TO MAIN MENU
IM956-A

POWER WAVE

C300
May, 2012
®
11479, 11723
For use with machines having Code Numbers:
Safety Depends on You
Lincoln arc welding and cutting
equipment is designed and built
with safety in mind. However,
your overall safety can be
increased by proper installation ...
and thoughtful operation on your
part. DO NOT INSTALL, OPER-
ATE OR REPAIR THIS EQUIP-
MENT WITHOUT READING
THIS MANUAL AND THE
SAFETY PRECAUTIONS CON-
TAINED THROUGHOUT. And,
most importantly, think before you
act and be careful.
IEC 60974-1
OPERATORʼS MANUAL
Copyright © Lincoln Global Inc.
• World's Leader in Welding and Cutting Products •
• Sales and Service through Subsidiaries and Distributors Worldwide •
Cleveland, Ohio 44117-1199 U.S.A.
TEL: 1.216.481.8100
For Service in U.S. and Canada: Call 1.888.935.3877
FAX: 1.216.486.1751
WEB SITE: lincolnelectric.com
For Non-U.S. Service: Email globalservice@lincolnelectric.com

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the power wave c300 and is the answer not in the manual?

Questions and answers

Related Manuals for Lincoln Electric power wave c300

Summary of Contents for Lincoln Electric power wave c300

  • Page 1: Power Wave

    RETURN TO MAIN MENU IM956-A POWER WAVE C300 May, 2012 ® 11479, 11723 For use with machines having Code Numbers: Safety Depends on You Lincoln arc welding and cutting equipment is designed and built with safety in mind. However, your overall safety can be increased by proper installation ...

  • Page 2: California Proposition 65 Warnings

    351040, Miami, Florida 33135 or CSA Standard W117.2-1974. A Free copy of “Arc Welding Safety” booklet E205 is available from the Lincoln Electric Company, 22801 St. Clair Avenue, Cleveland, Ohio 44117-1199. BE SURE THAT ALL INSTALLATION, OPERATION, MAINTENANCE AND REPAIR PROCEDURES ARE PERFORMED ONLY BY QUALIFIED INDIVIDUALS.

  • Page 3: Electric Shock Can Kill

    SAFETY ARC RAYS can burn. ELECTRIC SHOCK can 4.a. Use a shield with the proper filter and cover kill. plates to protect your eyes from sparks and 3.a. The electrode and work (or ground) circuits the rays of the arc when welding or observing are electrically “hot”...
  • Page 4 SAFETY WELDING and CUTTING CYLINDER may explode SPARKS can if damaged. cause fire or explosion. 7.a. Use only compressed gas cylinders 6.a. Remove fire hazards from the welding area. containing the correct shielding gas for the If this is not possible, cover them to prevent process used and properly operating the welding sparks from starting a fire.
  • Page 5 SAFETY 5. Toujours porter des lunettes de sécurité dans la zone de PRÉCAUTIONS DE SÛRETÉ soudage. Utiliser des lunettes avec écrans lateraux dans les zones où lʼon pique le laitier. Pour votre propre protection lire et observer toutes les instructions et les précautions de sûreté...
  • Page 6 2004/108/EC. It was manufactured in conformity with a national standard that implements a harmonized standard: EN 60974-10 Electromagnetic Compatibility (EMC) Product Standard for Arc Welding Equipment. It is for use with other Lincoln Electric equipment. It is designed for industrial and professional use. Introduction All electrical equipment generates small amounts of electromagnetic emission.
  • Page 7 SAFETY Electromagnetic Compatibility (EMC) The size of the surrounding area to be considered will depend on the structure of the building and other activities that are taking place. The surrounding area may extend beyond the boundaries of the premises. Methods of Reducing Emissions Public Supply System Welding equipment should be connected to the public supply system according to the manufacturer’s rec- ommendations.
  • Page 8 Electric for advice or information about their use of our products. We respond to our customers based on the best information in our posses- sion at that time. Lincoln Electric is not in a position to warrant or guarantee such advice, and assumes no liability, with respect to such infor- mation or advice.

  • Page 9: Table Of Contents

    viii viii TABLE OF CONTENTS Page Installation........................Section A Technical Specifications ....................A-1, A-2 Safety Precautions .......................A-3 Location, Lifting ......................A-3 Stacking ........................A-3 Tilting..........................A-3 Input and Ground Connections ..................A-3 Machine Grounding .......................A-3 High Frequency Protection....................A-3 Input Connection ........................A-4 Input Fuse and Supply Wire ..................A-4 Input Voltage Selection ....................A-4 Power Cord Replacement .....................A-4 Connection Diagram .....................A-5...

  • Page 10: Table Of Contents

    TABLE OF CONTENTS Page Maintenance ....................Section D Safety Precautions .......................D-1 Routine Maintenance ......................D-1 Periodic Maintenance......................D-1 Calibration Specification.......................D-1 ________________________________________________________________________________ Troubleshooting ....................Section E Safety Precautions....................E-1 How to Use Troubleshooting Guide...............E-1 Using Status LED and Error Fault Codes ..............E-2, E-4 Troubleshooting Guide................E-2 thru E-5 Error Fault Codes ......................E-6, E-7 ________________________________________________________________________________ Wiring Diagram and Dimension Print ............Section F...

  • Page 11: Installation

    INSTALLATION ® TECHNICAL SPECIFICATIONS - POWER WAVE C300 POWER SOURCE-INPUT VOLTAGE AND CURRENT Input Amperes Input Voltage ± 10% Model Duty Cycle Power Factor @ Idle Power (1 Phase in paren- Rated Output thesis) 30/28/16/14/11 40% rating 208/230/400*/460/575 (53/48/29/25/20) K2675-1 300 Watts Max.
  • Page 12 INSTALLATION GEARING - WIRE FEED SPEED RANGE-WIRE SIZE GMAW GMAW GEARING WFS RANGE GMAW FCAW MILD STEEL ALUMINUM STAINLESS WIRE SIZES WIRE SIZES WIRE SIZES WIRE SIZES Normal Speed 50 – 700 ipm .025 – .045" .030 – 3/64" .035 – .045" .035 –...

  • Page 13: Safety Precautions

    INSTALLATION LIFTING SAFETY PRECAUTIONS Read this Both handles should be used when lifting POWER WAVE ® entire installation section before you start installa- C300. When using a crane or overhead device a lifting strap tion. should be connected to both handles. Do not attempt to lift the WARNING POWER WAVE C300 with accessories attached to it.

  • Page 14: Input Connection

    INSTALLATION INPUT CONNECTION WARNING WARNING The POWER WAVE C300 ON/OFF ® switch is not intended as a service Only a qualified electrician should disconnect for this equipment. Only connect the input leads to the a qualified electrician should con- POWER WAVE C300.

  • Page 15: Recommended Work Cable Sizes

    INSTALLATION RECOMMENDED WORK CABLE SEMI-AUTOMATIC WELDING SIZES FOR ARC WELDING POLARITY A 15 ft. work cable is provided with the POWER Most GMAW welding procedures use Electrode WAVE C300. This cable is appropriately sized for all ® Positive welding. For these applications, connect the of the POWER WAVE C300ʼs welding procedures.

  • Page 16: Cable Connections

    INSTALLATION CABLE CONNECTIONS There are three circular connectors in the wire spool compartment on the POWER WAVE C300. ® (See 4-pin, 6-pin and 7-pin---Figure A.2---Table A.1) TABLE A.1 Function Wiring FIGURE A.2 Supply Voltage for Dual Procedure 4-pin trigger con- Dual Procedure Input nector for push- Trigger Input...

  • Page 17: Shielding Gas Connections

    INSTALLATION SHIELDING GAS CONNECTION 2. Remove the cylinder cap. Inspect the cylinder valves and regulator for damaged threads, dirt, dust, oil or WARNING grease. Remove dust and dirt with a clean cloth. DO NOT ATTACH THE REGULATOR IF OIL, GREASE OR DAMAGE IS PRESENT! Inform your gas supplier CYLINDER may explode if of this condition.

  • Page 18: Loading Spools Of Wire

    INSTALLATION LOADING SPOOLS OF WIRE WARNING • Keep hands, hair, clothing and tools away from rotating equipment. • Do not wear gloves when threading wire or changing wire spool. • Only qualified personnel should install, use or service this equipment. ------------------------------------------------------------------------ Loading 10 to 15 lb.

  • Page 19: Wire Drive Configuration

    INSTALLATION WIRE DRIVE CONFIGURATION 8. Connect the shielding gas hose to the new gun bushing, if required. (See Figure A.4) 9. Rotate the gun bushing until the thumb screw hole Changing the Gun Receiver Bushing aligns with the thumb screw hole in the feed plate. WARNING Slide the gun receiver bushing into the wire drive and verify the thumb screw holes are aligned.

  • Page 20: Gun Used

    A-10 A-10 INSTALLATION GUN USED 1. Press end of gun against a solid object that is elec- trically isolated from the welder output and press the gun trigger for several seconds. The Magnum 300 is the recommended gun for the POWER WAVE C300.

  • Page 21: Tig Welding

    A-11 A-11 INSTALLATION TIG WELDING SMAW WELDING (Figure A.7) Most SMAW welding procedures use Electrode Tig uses Electrode Negative Polarity so for this appli- Positive welding. For these applications, connect the cation, connect the Tig torch to the negative (-) output stick electrode holder to the positive (+) output stud stud and connect the work clamp to the positive (+) and connect the work clamp to the negative (-) output...

  • Page 22: Operation

    OPERATION SAFETY PRECAUTIONS GRAPHIC SYMBOLS THAT APPEAR ON THIS MACHINE OR IN THIS MANUAL READ AND UNDERSTAND ENTIRE SECTION BEFORE OPERATING MACHINE. WARNING WARNING OR CAUTION • ELECTRIC SHOCK CAN KILL. Unless using COLD FEED fea- ture, when feeding with gun trig- DANGEROUS ger, the electrode and drive VOLTAGE...

  • Page 23: Product Description

    OPERATION PROCESS LIMITATIONS PRODUCT DESCRIPTION The software based weld tables of the Power Wave C300 ® The Power Wave C300 is a high performance multi- ® limit the process capability within the output range and the process machine with GMAW, FCAW, SMAW, DC safe limits of the machine.

  • Page 24: Design Features

    OPERATION DESIGN FEATURES • Patent pending dual spring pressure arms have sensitivity for feeding soft wires without crushing Loaded with Standard Features them, and have plenty of compression force for feeding solid or stiff wires. • Multiple process DC output range: 5 - 300 Amps. •...

  • Page 25: Case Front Controls

    OPERATION CASE FRONT CONTROLS (Code 11479) FIGURE B.1 All operator controls and adjustments are located on 9. ON/OFF SWITCH- Controls power to the Power the case front of the Power Wave. (See Figure B.1) Wave C300. ® 1. LEFT DISPLAY- Shows wire feed speed or amper- 10.

  • Page 26: Case Back Controls

    OPERATION CASE BACK CONTROLS (Code 11479) FIGURE B.2 1. ETHERNET CONNECTOR 2. POWER CORD 3. GAS CONNECTION POWER WAVE C300 ®...

  • Page 27: Internal Controls

    OPERATION INTERNAL CONTROLS (Code 11479) FIGURE B.3 7. NEGATIVE STUD 1. SPINDLE BRAKE 8. GAS CONNECTION 2. WIRE DRIVE PRESSURE ARM 9. POSITIVE STUD 3. THUMB SCREW, FOR SECURING THE WELDING GUN 10. COLD INCH / GAS PURGE SWITCH 4. GUN BUSHING 11.

  • Page 28: Making A Weld With Waveform Technology Power Sources

    Weld Set ® responsibility of the builder/user. Many variables Reference Guide supplied with the machine or avail- beyond the control of The Lincoln Electric able at www.powerwavesoftware.com. Company affect the results obtained in applying these programs. These variables include, but are...

  • Page 29: Procedure/Memory Panel Operation

    OPERATION CASE FRONT CONTROLS USED WIRE FEED SPEED (WFS) VOLTS AMPS TRIM OUTPUT MORE OUTPUT LESS AMPS AMPS SETUP IR PORT WELD MODE START OPTIONS UltimArc™ Control END OPTIONS DUAL PROCEDURE/ MEMORY PANEL OPERA- TION POWER WAVE C300 ®...
  • Page 30 OPERATION SMAW (STICK) WELDING SMAW is most often used for outdoor construction, pipe welding and general repairs. The wire feeder controls Amperage, Output Control and Arc Force dur- ing SMAW welding. During SMAW welding the wire drive remains idle. BASIC OPERATION VOLTS TRIM AMPS...
  • Page 31 B-10 B-10 OPERATION NON-SYNERGIC GMAW AND FCAW UltimArc™Control, adjusts the apparent inductance of WELDING the wave shape. The UltimArc™Control adjustment is similar to the “pinch” function in that it is inversely pro- In non-synergic modes, the WFS control is similar to a portional to inductance.
  • Page 32 B-11 B-11 OPERATION GMAW (MIG) SYNERGIC WELDING Synergic CV programs feature an ideal voltage best suited for most procedures. Use this voltage as a starting point and adjust if needed for personal prefer- For each wire feed speed, a corresponding voltage is ences.
  • Page 33 B-12 B-12 OPERATION STEEL AND STAINLESS SYNERGIC GMAW-P (PULSED MIG) WELDING When pulse welding, the power source primarily regu- Trim adjusts the arc length and ranges from 0.50 to 1.50 with a nominal value of 1.00. Increasing the trim lates the arc current, not the arc voltage. During a pulsing cycle, arc current is regulated from a low value increases the arc length.
  • Page 34 B-13 B-13 OPERATION STEEL AND STAINLESS GMAW-P (PULSED MIG) WELDING BASIC OPERATION 1.06 VOLTS TRIM AMPS More Shorter Longer Less Deposition Deposition START OPTIONS CONTROL OPTIONS EFFECT DESCRIPTION Postflow Time Adjusts the time that shielding gas flows after the trigger is WELD MODE pulled and prior to feeding wire.
  • Page 35 B-14 B-14 OPERATION ALUMINUM SYNERGIC GMAW-P ALUMINUM GMAW-P AND GMAW-PP (PULSED MIG)AND GMAW-PP (PULSE ON PULSE) WELDING ALUMINUM PULSE WELDING Synergic GMAW-P (Pulsed MIG) welding is ideal for low spatter, out of position and reduced heat input The Power Wave C300 can produce top quality alu- ®...
  • Page 36 B-15 B-15 OPERATION ALUMINUM GMAW-P (PULSED MIG) AND GMAW-PP (PULSE ON PULSE) WELDING BASIC OPERATION 1.06 VOLTS TRIM AMPS More Longer Shorter Less Deposition Deposition CONTROL OPTIONS START OPTIONS EFFECT DESCRIPTION Postflow Time Adjusts the time that shielding gas flows after the trigger is pulled and prior to feeding wire.
  • Page 37 B-16 B-16 OPERATION GTAW (TIG) WELDING The Power Wave C300 is excellent for Touch Start ® TIG welding. BASIC OPERATION Maximum Amperage VOLTS TRIM AMPS OUTPUT OUTPUT CONTROL OPTIONS WELD MODE MODE TOUCH START START OPTIONS No Arc starting Options are active for Touch Start TIG SETUP IR PORT...

  • Page 38: User Memories

    B-17 B-17 OPERATION DUAL PROCEDURE/MEMORY PANEL USER MEMORIES OPERATION Recall a memory with memory buttons To recall a user memory, press one of the eight user The Dual Procedure/Memory Panel performs three memory buttons. The memory is recalled when the functions: button is released.
  • Page 39 B-18 B-18 OPERATION LIMITS Set Limits: Limits allow the welder to adjust the welding proce- Press 5 dure only within a defined range. seconds Each user memory may have a different set of limits. For example, memory 1 can be set to limit the WFS to GUN B 200 through 300 in/min, and memory 2 can be set to limit the WFS to 275 through 310 in/min, while memo-...
  • Page 40 B-19 B-19 OPERATION If the passcode does not equal zero (0000), enter the The memory value must always be less than or equal passcode now. If the passcode has been forgotten, a to the high limit, and greater than or equal to the low limit.
  • Page 41 B-20 B-20 OPERATION 2-STEP 4-STEP- TRIGGER OPERATION The 2-Step - 4-Step switch changes the function of the gun trigger. 2-Step trigger operation switches the welding output ON-OFF in direct response to the trig- ger. 4-Step trigger operation provides 'trigger interlock' capability and gives the ability to control the amount of time spent in the arc start and arc crater steps.
  • Page 42 B-21 B-21 OPERATION EXAMPLE 1 - 2 STEP TRIGGER: Simple operation The simplest trigger operation occurs with a 2 Step trigger and the Start, Crater and Burnback functions all set to OFF. (See Figure B.11) For this sequence, PREFLOW: Shielding gas begins to flow immediately when the gun trigger is pulled.
  • Page 43 B-22 B-22 OPERATION EXAMPLE 2 - 2 STEP TRIGGER: Improved Arc Start UPSLOPE: and Arc End. Tailoring the arc start and arc end is a Once the wire touches the work and an arc is estab- common method for reducing spatter and improving lished, both the machine output and the wire feed weld quality.
  • Page 44 B-23 B-23 OPERATION EXAMPLE 3 - 2 STEP TRIGGER: Customized Arc WELD: Start, Crater and Arc End. Sometimes it is advanta- After upslope, the power source output and the wire geous to set specific arc start, crater and arc ending feed speed continue at the weld settings.
  • Page 45 B-24 B-24 OPERATION EXAMPLE 4 – 4 STEP TRIGGER: Trigger Interlock The 4 step trigger can be configured as a trigger inter- lock. Trigger interlock adds to the welderʼs comfort when making long welds by allowing the trigger to be released after an initial trigger pull.
  • Page 46 B-25 B-25 OPERATION UPSLOPE: EXAMPLE 5 - 4 STEP TRIGGER: Manual control of During upslope, the power source output and the wire Start and Crater times with Burnback ON. The 4 step feed speed ramp to the weld settings throughout the trigger sequence gives the most flexibility when the start time.

  • Page 47: Cold Feed/Gas Purge Switch

    B-26 B-26 OPERATION COLD FEED/GAS PURGE SWITCH COLD FEED Cold Feed and Gas Purge are com- bined into a single spring centered tog- gle switch. To activate Cold Feeding, hold the GAS PURGE switch in the FORWARD position. The wire drive will feed electrode but neither the power source nor the gas solenoid will be energized.

  • Page 48: Set-Up Feature Menu

    B-27 B-27 OPERATION SETUP MENU FEATURES The Setup Menu gives access to the Setup Configuration. Stored in the setup configuration are user parameters that generally only need to be set at installation. The parameters are grouped as shown in the following table. PARAMETER DEFINITION P.1 through P.99...
  • Page 49 B-28 B-28 OPERATION USER DEFINED PARAMETERS Parameter Definition Exit Setup Menu This setup menu parameter can be used to exit the setup menu. When P.0 is displayed, press the left Mode Select button to exit the setup menu. Wire Feed Speed Units P.1 selects which units wire feed speed will be displayed in.
  • Page 50 B-29 B-29 OPERATION USER DEFINED PARAMETERS Parameter Definition Procedure Change Method Selects how remote procedure selection (A/B) will be made. The selected procedure can be changed locally at the user interface by pressing the 'A-Gun-B' button. The following methods can be used to remotely change the selected procedure: •...
  • Page 51 B-30 B-30 OPERATION USER DEFINED PARAMETERS Parameter Definition Gun Offset Adjustment Range: -30 to 30 (default = 0) Adjusts the wire feed speed calibration of the pull motor of a push-pull gun. This should only be performed when other possible corrections do not solve any push-pull feeding problems. An rpm meter is required to perform the pull gun motor offset calibration.
  • Page 52 B-31 B-31 OPERATION USER DEFINED PARAMETERS Parameter Definition P.16 Push-Pull Gun Knob Behavior Determines how the potentiometer on the Push/Pull torch will behave. • Gun Pot Enabled = The welding wire feed speed is always controlled by the potentiometer on the push-pull gun (default).
  • Page 53 B-32 B-32 OPERATION USER DEFINED PARAMETERS Parameter Definition P.103 View Software Version Information Used for viewing the firmware versions for each board in the system. Press the right MSP Button to enter the option. Rotate Set knob to select the desired board to read. Press the right button again to read the firmware version.
  • Page 54 B-33 B-33 OPERATION USER DEFINED PARAMETERS Parameter Definition P.503 Memory Button Disable Disables the specified memory button(s). When a memory is disabled, welding procedures can- not be restored from or saved to that memory. If an attempt is made to save or restore a dis- abled memory, a message will be displayed on the Mode Select Panel indicating the memory number is disabled.
  • Page 55 B-34 B-34 OPERATION USER DEFINED PARAMETERS Parameter Definition P.507 UI Clear All Memories Allows the operator to quickly set all memories to the default weld mode and welding parame- ters. Presently, this option does not exist in any setup menu. P.509 UI Master Lockout Locks all user interface controls, preventing the operator from making any changes.

  • Page 56: Accessories

    ACCESSORIES K1783-4 OPTIONS / ACCESSORIES PTA-26 TIG Torch (25 ft 7.6m) 2 CABLES STICK OPTIONS K1783-7 K875 ACCESSORY KIT - 150 Amp PTA-26V TIG Torch (12.5 ft 3.8m) 2 CABLES K1783-9 For stick welding. Includes 20 ft. PTA-26V TIG Torch (25 ft 7.6m) 2 CABLES (6.1m) #6 electrode cable with lug, 15 ft.
  • Page 57 (qty. 2), non-metallic wire guides and cable PUSH PULL GUNS liner. Lincoln Electric offers both the Cougar™ pistol grip K489-8 FAST-MATE ADAPTER KIT and Panther™ gooseneck style push-pull guns for feeding aluminum wire. Allows guns with a Fast-Mate adapter kit type back end to plug into a POWER K2874-1 PANTHER™...

  • Page 58: Safety Precautions

    MAINTENANCE SAFETY PRECAUTIONS WARNING ELECTRIC SHOCK can kill. • Do not operate with covers removed. • Turn off power source before installing or servicing. • Do not touch electrically hot parts. • Turn the input power to the welding power source off at the fuse box before working in the terminal strip.

  • Page 59: How To Use Troubleshooting Guide

    HOW TO USE TROUBLESHOOTING GUIDE WARNING Service and Repair should only be performed by Lincoln Electric Factory Trained Personnel. Unauthorized repairs performed on this equipment may result in danger to the technician and machine operator and will invalidate your factory warranty. For your safety and to avoid Electrical Shock, please observe all safety notes and precautions detailed throughout this manual.
  • Page 60 TROUBLESHOOTING USING THE STATUS LED TO There is an audible beeper associated with this input control boardʼs status light. So the error codes on the input board TROUBLESHOOT SYSTEM PROBLEMS can be detected through either the status light or the status beeper.
  • Page 61 TROUBLESHOOTING Observe all Safety Guidelines detailed throughout this manual ERROR CODES FOR THE POWER WAVE ® The following is a partial list of possible error codes for the POWER WAVE C300. For a complete listing consult ® the Service Manual for this machine. MAIN CONTROL BOARD ( “STATUS”...
  • Page 62 TROUBLESHOOTING Observe all Safety Guidelines detailed throughout this manual INPUT CONTROL BOARD Error Code # Indication Peak input current limit Input current limit has been exceeded. Typically indicates short term power overload. If problem persists contact Service Department. Under-voltage lockout +15 VDC supply on Input control board too low.
  • Page 63 3. Contact your local authorized 3. Major physical or electrical dam- Lincoln Electric Field Service age is evident when the covers facility for technical assistance. are removed. 1. Make sure input supply discon- Machine will not power up (no lights) 1.
  • Page 64 TROUBLESHOOTING Observe all Safety Guidelines detailed throughout this manual PROBLEMS POSSIBLE RECOMMENDED (SYMPTOMS) CAUSE COURSE OF ACTION Thermal LED is ON Improper fan operation Basic Machine Problems (Continued) 1. Check for proper fan operation. Thermal LED is ON 1. Improper fan operation. Fan should run in a low speed setting when the machine is idle and in a high speed when the...
  • Page 65 TROUBLESHOOTING Observe all Safety Guidelines detailed throughout this manual PROBLEMS POSSIBLE RECOMMENDED (SYMPTOMS) CAUSE COURSE OF ACTION Weld and Arc Quality Problems (Continued) Wire burns back to tip at the end of 1. Burnback Time 1. Reduce burnback time and/or the weld.
  • Page 66 TROUBLESHOOTING Observe all Safety Guidelines detailed throughout this manual PROBLEMS POSSIBLE RECOMMENDED (SYMPTOMS) CAUSE COURSE OF ACTION Ethernet Cannot Connect 1. Physical connection. 1. Verify that the correct patch cable or cross over cable is being used (refer to local IT department for assistance).
  • Page 67 DIAGRAMS ENHANCED DIAGRAM POWER WAVE C300 ®...
  • Page 68 DIMENSION PRINT POWER WAVE C300 ®...
  • Page 69 NOTES POWER WAVE C300 ®...
  • Page 70 Do not touch electrically live parts or Keep flammable materials away. Wear eye, ear and body protection. WARNING electrode with skin or wet clothing. Insulate yourself from work and ground. Spanish No toque las partes o los electrodos Mantenga el material combustible Protéjase los ojos, los oídos y el AVISO DE bajo carga con la piel o ropa moja-...
  • Page 71 Keep your head out of fumes. Turn power off before servicing. Do not operate with panel open or WARNING Use ventilation or exhaust to guards off. remove fumes from breathing zone. Spanish Los humos fuera de la zona de res- Desconectar el cable de ali- No operar con panel abierto o AVISO DE...
  • Page 72 Need Help? Lincoln Electric “Rapid Response” Service! Call 1.888.935.3877 to talk to a Service Representative Hours of Operation: 8:00 A.M. to 6:00 P.M. (ET) Mon. thru Fri. After hours? Use “Ask the Experts” at lincolnelectric.com A Lincoln Service Representative will contact you by the next business day.

Table of Contents

Save PDF