Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Palsonic 2418
Summary of Contents for Palsonic 2418
- Page 1 OWNER'S MANUAL 24CM AC/DC REMOTE COLOUR TELEVISION MODEL: 2418 PALSONIC CORPORATION PTY LTD 1 JOYNTON AVENUE WATERLOO NSW 2017 AUSTRALIA TEL:(02)9313 7111 FAX:(02)9313 7555 www.palsonic.com.au PALSONIC CUSTOMER SERVICE TELEPHONE AUSTRALIA:1300 657 888...
-
Page 2: Above All
This equipment has been designed and manufactured to meet the highest international standards, but, like any electrical apparatus which is operated at mains voltage, care must be taken if you are to obtain the best results and safety is to be assured. This is particularly important with audio and TV equipment. - Page 3 IR RECEIVER CONTROL BOARD FUSE INDICATOR SKIP AUTO PSET STAND BY CHANNEL SELECTOR CALL PREVIOUS TIME TIMER PICTURE/TIME ( ANT. PLUG ANT IN VIDEO IN AUDIO IN AUDIO OUT MUTE CHANNEL SELECTOR ( VOLUME CONTROL ( SLEEP PICTURE ANTENNA DEGAUSSING SWITCH DC IN EARPHONE JACK...
-
Page 4: Installing Batteries
INSTALLING BATTERIES : 1. Remove the battery cover of Remote Control Unit. 2. Insert two "AAA" 1.5V batteries making sure the polarity (+ or -) of the batteries matches the polarity marks inside the unit. 3. Close the battery cover. * When the Remote Control Unit is not used for a long time or the batteries are worn out, take out the batteries to... -
Page 5: Dc Power Supply
DC POWER SUPPLY: Be sure the DC power supply is 12V- 14V, attach the plug of DC power cord to the DC socket on the back of the cabinet. The set will be in stand by mode, the power indicator is red. If this television is being used in a mobile installation, attach the small connector of the supplied Car Battery Cord... -
Page 6: Manual Tuning
CHANNEL PRESET AUTO PRESET 1. Press the PSET (PRESET ON/OFF) button on the front panel. The current band and channel position will be displayed on screen (in green). 2. Press AUTO (AUTO PRESET) button, the appliance will search the signal of TV station in the order of VHFL, VHFH and UHF, as shown in the following, and memorise them from channel number 1 position. -
Page 7: Operation
SKIP BUTTON: FUNCTION: When CHANNEL SELECTOR button is used to select channels, the channel will be skipped if they are set to "SKIP" mode. For example: Set 2~7 channels to "SKIP" mode, the procedure of channel position increasing or decreasing. (REMOTE) OPERATION: 1. -
Page 8: Standby Button
PICTURE CONTROL (REMOTE CONTROL UNIT) Press the PICTURE CONTROL button on the Remote Control Unit. The FUNCTION to be adjusted is selected in sequence as shown in the following chart at every press of the button. PICTURE Adjust the button to obtain satisfactory picture. ON SCREEN DISPLAY CAPTION... - Page 9 SLEEP BUTTON (REMOTE CONTROL UNIT) Using SLEEP button allows you to have the appliance automatically turned off a predetermined time, and set the appliance to stand by mode. SLEEP After the SLEEP function is set, the remaining time will be automatically displayed for 4 seconds every ten minutes.
- Page 10 4. Use CALL button to display the present time on screen. See "CALL" operation * In case of power failure, the clock operation will be cancelled. ON TIME OPERATION: 1. Set the CLOCK in operation mode. 2. Press the TIMER button until "ON TIME" displays on the screen. 3.
- Page 11 the upper comer of the screen for 4 seconds. Press AV/TV button again to return TV mode, the original channel will be displayed in the upper right comer of the screen. Set to TV mode when receiving or recording TV program. AV CONNECTOR This TV set is equipped with AUDIO/VIDEO input jacks and AUDIO output jack for your desired equipment to be connected.
-
Page 12: Troubleshooting Guide
TROUBLE SHOOTING GUIDE Many apparent malfunctions may be caused by slight misadjustment of regular controls or some other equally similar simple causes. If any problem arises in the operation of your set, first check through this list of symptoms and correction. Should the problem be unsettled, unplug the set and contact your dealer. -
Page 13: Specifications
SPECIFICATIONS : TV System Power Supply Channel Coverage Cable channel Audio output Antenna Impedance Dimension (W x H x D) Weight AC power adapter Power input Power output Dimension (W x H x D) Weight Car Battery Cord Remote Control Unit Power Supply * Design and specifications are subject to change without notices. - Page 14 PALSONIC CORPORATION PTY LTD 1 JOYNTON AVENUE WATERLOO NSW 2017 AUSTRALIA TEL:(02)9313 7111 FAX:(02)9313 7555 www.palsonic.com.au PALSONIC CUSTOMER SERVICE TELEPHONE AUSTRALIA: 1300 657 888 604-10203-01...