Muffler; Starter - Husqvarna 440e II TrioBrake Operator's Manual

Hide thumbs Also See for 440e II TrioBrake:
Table of Contents

Advertisement

Available languages

Available languages

Grasp the chain saw firmly, wrapping your fingers and
thumbs around the handles. (62)
Apply full throttle and activate the chain brake by tilting
your left wrist forward onto the front hand guard. Do not let
go of the front handle. The chain should stop
immediately. (58)
Throttle lockout
Make sure the throttle control is locked at the idle
setting when the throttle lockout is released. (101)
Press the throttle lockout and make sure it returns to
its original position when you release it. (102)
Check that the throttle trigger and throttle lockout
move freely and that the return springs work properly.
(103)
Start the chain saw and apply full throttle. Release the
throttle control and check that the chain stops and
remains stationary. If the chain rotates when the
throttle control is in the idle position you should check
the carburetor idle adjustment.
Chain catcher
Check that the chain catcher is not damaged and is firmly
attached to the body of the chain saw. (104)
Right hand guard
Check that the right hand guard is not damaged and that
there are no visible defects, such as cracks. (11)
Vibration damping system
Regularly check the vibration damping units for cracks or
deformation. Make sure the vibration damping units are
securely attached to the engine unit and handle unit.
(105)
Stop switch
Start the engine and make sure the engine stops when
you move the stop switch to the stop setting. (59)
CAUTION! The start/stop switch automatically returns to
run position. In order to prevent unintentional starting, the
1155361-49 Rev.2 2014-11-26
MAINTENANCE
spark plug cap must be removed from the spark plug
when assembling, checking and/or performing
maintenance.
Muffler
Never use a machine that has a faulty muffler.
Regularly check that the muffler is securely attached to
the machine. (106)
Some mufflers are equipped with a special spark arrestor
screen. If your machine has this type of muffler, you
should clean the screen at least once a week. This is best
done with a wire brush. A blocked screen will cause the
engine to overheat and may lead to serious damage.
Note! The screen must be replaced if it is damaged. If the
screen is blocked the machine will overheat and this will
cause damage to the cylinder and piston. Never use a
machine with a muffler that is in poor condition. Never
use a muffler if the spark arrestor screen is missing
or defective. (13)
The muffler is designed to reduce the noise level and to
direct the exhaust gases away from the operator. The
exhaust gases are hot and can contain sparks, which may
cause fire if directed against dry and combustible
material.

Starter

!
Replacing the starter cord
Loosen the screws that hold the starter against the
crankcase and remove the starter. (107)
Pull out the cord approx. 30 cm (12 inches) and hook
it into the notch in the rim of the pulley. Release the
recoil spring by letting the pulley rotate slowly
backwards. (108)
Undo the bolt in the centre of the pulley and remove
the drive disc (A), drive disc spring (B) and the pulley
(C). Insert and secure a new starter cord in the starter
pulley. Wind approx. 3 turns of the starter cord on the
starter pulley. Fit the starter pulley so that the end of
the recoil spring (D) hooks into the starter pulley. Now
assemble the drive disc spring, drive disc and the bolt
WARNING! When the recoil spring is
wound up in the starter housing it is
under tension and can, if handled
carelessly, pop out and cause personal
injury.
Care must be exercised when replacing
the return spring or the starter cord.
Wear protective glasses and protective
gloves.
English
27

Advertisement

Table of Contents
loading

This manual is also suitable for:

445 epa ii, 445e epa ii, 450e

Table of Contents