Connecting Tbsu And Rbsu/Rbss Station Devices (Nt-Mode) - Toshiba STRATA DK14 Installation And Maintenance Manual

ISDN Interfaces
RBSU/RBSS and TBSU Interface Units
Most NT1 devices have TR option switches; if the NT1 does not have TRs, two 100-ohm TRs
must be wired into the NT1 modular jack - one 100-ohm resistor across each pair (Tx and Rx).
Refer to the NT1 manufacturers documentation for the maximum loop length between the NT1
and the network jack. The maximum loop length between the NT1 and the TBSU or RBSU circuit
is 1650 feet.
TBSU or RBSU
TE-Circuit
Switch in
100-ohm TR
using RBSU
option switch.
Note: T and U are ISDN standard
reference points.
Figure 16-17 TBSU or RBSU to NT1 Point-to-point Connection

Connecting TBSU and RBSU/RBSS Station Devices (NT-Mode)

S-type TAs and TE-1s can be connected to the station side of TBSU, RBSU, and RBSS circuits.
TA and TE devices must be powered by local AC power using AC adapter supplied with the TA or
TE device. The TBSU and RBSU/RBSS circuits must be configured in the NT mode when
connected to TA and TE devices (refer to option switches in
16-12 on Page 16-21
The TA enables you to connect non-ISDN voice and data devices to ISDN BRI circuits. The TA
matches the protocol of existing interfaces (R-reference point) to the ISDN S/T protocol (see
Figure on
RS-232 async data (like data from a PC COM port) to B-channel 64 kbps sync.
TAs also enable you to connect standard telephones and non-ISDN fax machines to receive and
make calls over ISDN circuits. TEs include any user device (telephone, fax, PC video conference
board) that is designed to plug directly into the ISDN (S/T) interface without the use of a TA.
There are two types of ISDN TA and TE-1 devices: the U-type and the S/T type. Most
manufacturers of ISDN station devices make both types. In DK424 or DK424i R4.1 and DK40i,
the TBSU and RBSU/RBSS station side, BRI-NT circuits only function with S/T type TA and TE-
1 devices. You cannot connect U-type TE-1 or TA devices to the TBSU or RBSU/RBSS BRI-NT
circuits.
Also, connecting an NT1 to the TBSU or RBSU/RBSS BRI-NT circuit to convert from S/T to U
interface is not supported to enable the use of U-type TE-1 or TA device on the station side of the
TBSU or RBSU/RBSS. U-type TE-1 and TA device interface is provided in the DK by the TBUU
and RBUU/RBUS BRI circuit only. TBUU and RBUU/RBUS will be provided in the DK424 or
DK424i and DK40i Release 4.3.
16-26
RJ45 Pinout
(TBSU or RBSU - BRI jack)
BRI
(four-wire)
3
TX
6
TX
4 RX
5 RX
T
and Program *60).
Page 16-3). TA devices include asynchronous circuit-switched adapters that convert
RJ45 Pinout
(NT1 - S/T jack)
3
RX
6
RX NT-1
Switch
in 100-ohm
TX 4
TR.
TX 5
Table 16-10 on Page 16-18
BRI
(two-wire)
4 RX/TX
Network
BRI-line
5 RX/TX
RJ-11 Jack
U
Demarcation Point
Local AC
Power
Strata DK I&M
3343
and Table
6/00