AEG BSS 4815 Instruction Manual page 6

English
36
13 TREBLE+/TREBLE- buttons (adjust trebles)
BASS+/BASS buttons (adjust basses)
14 button (On/Operational readiness)
Wall mounting
A Threaded bolt (2x)
B Mounting plate (2x)
C Countersunk screw (4x)
D Dowel (4x)
First Use of the Device/Introduction
• Select a proper place for the device. A dry, level and slip
proof surface is suitable.
• Make sure the device is vented sufficiently!
• Remove the protective film from the device, if present.
Wall mounting (Sound bar)
You can also mount the device to the wall.
CAUTION:
Make sure beforehand whether there are cables in the wall
which could be damaged!
NOTE: Check the reach of the cable!
To mount the device, make sure that an easily accessible
plug outlet is available within reach of the power cable.
The distance between the mountings for wall mounting is
618 mm.
• Hold the mounting plate (B) to the wall so that the above-
listed distance is kept horizontally and from the center of
the mounting plates.
• Mark the four positions of the mounting holes with a pen-
cil.
• Drill the mounting holes (diameter 6 mm).
• Stick the dowels (D) into the boreholes and fasten the
mounting plates to the wall with the countersunk screws
(C).
• Twist the threaded bolts (A) into the back side of the
sound bar so far that there is enough space between the
wall and the connection cable.
CAUTION: IMPORTANT!
For an optimal wall mounting we recommend the use
of connection cables with an angled connection. You
can obtain corresponding cables from the specialist
shop.
• Hang the device into the mounting plates (B) with the
screws (A). Check for stable support.
Establish a power supply and wireless subwoofer connec-
tion.
The wireless connection of the subwoofer is created automa-
tically.
• Set up the subwoofer in a radius of 5 meters to the sound
bar.
• Make sure the grid voltage corresponds to the figures on
the rating plate.
• Plug the power plug of both devices into a properly
installed protective wall socket.
• Turn on the sound bar by switching the power switch
(5) on the backside of the device to the "ON" position.
• Now turn on the subwoofer by switching the power switch
on the back side of the device to the "ON" position.
The connection is established as soon as you turn on the
sound bar with the
NOTE:
• Once the connection is established, the control light
of the subwoofer will light up. If no connection was
established, the LED will flash. If no connection is made
within about 5 Minutes the LED goes out.
• Disconnect from mains power supply during longer
periods of non-use.
Insert/Replace Battery in Remote Control
NOTE:
The lithium cell in the battery compartment of the remote
control was possibly secured with a foil for the transport.
This prolongs the lifetime of the battery. Please remove this
foil before the first use to make the remote control ready
for operation.
• Open the battery compartment on the underside of the
remote.
• Replace the cell with a battery of the same type (CR
2025). Check that the polarity is correct (see battery com-
partment).
• Close the battery compartment.
If the remote is not in use for a lengthy period of time, please
remove the battery to prevent the battery acid from "leaking".
WARNING:
• Do not expose the batteries to intense heat, such as
sunlight, fire or similar. Danger of explosion!
• Keep batteries out of the reach of children. They are
not toys.
• Do not force batteries open.
• Avoid contact with metallic objects. (Rings, nails, screws
etc.) Danger of short circuits!
• Short circuits may overheat or even ignite batteries.
This may lead to combustion.
• When transporting the batteries, cover the terminals for
your safety with an adhesive strip.
• If a battery leaks, do not rub the fluid into the eyes or
the skin. If acid comes into contact with the eyes, rinse
with purified water and seek medical advice if symp-
toms persist.
button (14).