Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for Enorphin.es Shuttle Control
- Page 1 HUTTLE ONTROL Launch Instructions v. 2.0.2...
- Page 2 • up to 8 voices of polyphony, polyphonic key aftertouch, no steps in CC voltages, MIDI clock, Tap Clock, Tap LFO, bi-directional USB-MIDI transfer and many more MIDI events can be translated into CV Shuttle Control consists of the following parts: • Switched mode PSU •...
- Page 3 There is the option to power the Shuttle Control from a bus board in case you already have a powered bus and don’t plan to use Shuttle Control’s power adapter. You may connect SC into the powered bus board directly using the supplied flying board or any other 16-pin ribbon cable.
- Page 4 Those are most of USB-to-MIDI adapters, USB MIDI keyboards and controllers. Refer to the manual of certain hardware. By itself, Shuttle Control acts also as a generic device when is connected to MAC/PC or iPad, that means – no drivers are required and it will immediately appear in the list for your MIDI (or Core MIDI) hardware.
- Page 5 In case the connection between the USB devices or PC is lost, you may press and hold the DOWN button for about 2.5 seconds. There is no need to reboot (turn off and on) your whole system. That will result in Shuttle Control’s soft reset (it will choose preset number 1 preset) and will reinitialize all devices connected to the USB ports.
- Page 6 -5V to +5V. Shuttle Control has a 12 bit digital-to-analog converter that means all the voltage values at every CV output contain ~4 thou- sand values (4096 steps) for the full -5V/+5V range. Pitchbend messages by MIDI specifications are 14 bit (over 16 thousand values) and sending (squeezing) them thru 12 bit DAC doesn’t feel that crucial for ears.
- Page 7 9. Aftertouch Uni / Bi – stands for the MIDI channel pressure. Same as with velocity, it can be unipolar: from 0 to +5V, or bipolar from -5V to +5V and corresponds to a certain MIDI channel. 10. Key pressure Uni / Bi –...
- Page 8 Press ‘Auto’ to disable repeating all tracks playback. Choose your loaded midi file with the presets and press ‘Play’. A free ver- sion of that app will not play the last quarter of a midi file, however that’s enough to load a preset into Shuttle Control.
- Page 9 Windows that is able to play mid/syx files and upload them into Shuttle Control. First connect your Shuttle Control to your PC via to device connector (micro USB or type B to USB type A cable). Do not launch MIDI OX, but a MIDIBAR.EXE utility app –...
- Page 10 MIDI implementation chart Model: Endorphines Shuttle Control, Model rev. 5 dd. 02/02/2015 Function Remarks MIDI channel 1-16, OMNI Bank select 120 midi notes, 10 octaves in total with 1v/ Note numbers notes #7...#127 oct scale Program change Velocity: Note On...
- Page 11 Here is an approximate list of PSUs you may hook to your Shuttle Control. Approximate means that the Shuttle Control with work with any AC adapter that delivers 12-20V with 3A or more current (equiv- alent to 36 Watt or more power). The more is better; less isn't good and if it then works properly depends on how huge your system is.
- Page 12 SHUTTLE CONTROL V.2 BI-DIRECTIONAL MIDI TRANSFER Route from device to host: Route from host to device: Route host loopback: © 2013-2015 – Endorphin.es – Cargo page 11 of 14...
- Page 13 SHUTTLE CONTROL V.2 FACTORY PRESETS 0-7 CHEAT SHEET [ ] host loopback [+] host to device test preset, all white noises * start up preset on every output monophonic general setup [+] device to host white noise white noise 1v/oct voice1 gate 0..+5v voice1...
- Page 14 SHUTTLE CONTROL V.2 FACTORY PRESETS 8-F CHEAT SHEET preset configutaion: 8 voices preset configutaion: Hz/volt polyphonic configuration monophonic setup 1v/oct voice1 gate 0..+5v voice1 hz/volt voice1 s-trig +5...0v voice1 gate 0..+5v voice2 trigger 0..+5v voice1 1v/oct voice2 hz/volt voice1 1v/oct voice3 CC#any smooth 0...+5v...
- Page 15 SHUTTLE CONTROL V.2 EMPTY PRESETS CHEAT SHEET [ ] host loopback [ ] host loopback [ ] host to device [ ] host to device [ ] device to host [ ] device to host [ ] host loopback [ ] host loopback...
Need help?
Do you have a question about the Shuttle Control and is the answer not in the manual?
Questions and answers