Table of Contents
Advertisement
EN
|
Troubleshooting guide
Problem
Solution
The appliance
Turn the bowl or lid or the blender jar clockwise until
doensn't go on and
you hear a click. Check if the screw cap has been
the light ring round
correctly assembled on the motor housing when the
the stop button starts
blender is not used. Make sure that the dots indicated
to blink red after a
on the bowl and lid are directly opposite each other
process button or the
and the dot on the bowl is directly opposite the dot
pulse button has been
on the motor housing. In case the blender is attached,
pressed.
make sure the rib on the blender jar is directly
opposite the print on the motor housing.The red light
will stop blinking as soon as all attachments have been
correctly assembled.
The appliance
The thermal safety cut-out has probably cut off the
suddenly stopped
power supply to the appliance because it has
running
overheated. 1) Press the stop button. 2) Unplug the
appliance. 3) Let the appliance cool down for
60 minutes. 4) Put the mains plug in the socket.
5) Switch the appliance on again.
You have pressed the
Press the button for the process you want.
wrong process button
Both the blender jar
If both the blender jar and the food-processing bowl
and the food
have been mounted correctly, only the blender will
processing bowl are
work. If you want to use the food-processing bowl,
attached, but only the
remove the blender jar and assemble the screw cap.
blender works.
The + or - button
When the maximum load of the motor has been
does not respond
reached, pressing the + or - button will not have the
during certain
expected effect.This will especially happen when you
processes.
are processing large quantities of dough. Check the
quantities and processing times mentioned in the
table.
The kneading or
Check if you have really turned the bowl and the lid
balloon beater doesn't
clockwise as far as the point where you hear a click.
turn.
Problem
Solution
Can I also mince
No!
bones or bacon rind
with the meat mincer?
The meat looks as if it
Check whether the cutting edges of the cutter unit
has been 'pressed
are pointing outwards.
through' rather than
minced.
The metal parts of
The parts have been cleaned in the dishwasher.You
the meat mincer look
should clean all parts by hand and dry them
rusty.
immediately with a tea towel.
The meat mincer
Make sure the gear housing and the cutter housing
does not work.
have been assembled correctly.You will hear a click
when they have been fastened properly.
Is it possible to mince
No!
frozen meat with the
meat mincer?
PL
|
Rozwiązywanie problemów
Problem
Rozwiązanie
Urządzenie nie
Obróć w kierunku zgodnym z ruchem wskazówek
uruchamia się i po
zegara misą malaksera, pokrywą lub dzbankiem
wciśnięciu przycisku
blendera, aż usłyszysz kliknięcie. Sprawdź, czy na
przerabiania lub
obudowę silnika została prawidłowo wkręcona
przycisku pracy
zatyczka podczas nieużywania blendera. Upewnij się,
impulsowej pierścień
czy kropka na pokrywce oraz kropka na misce znajdują
świetlny wokół
się dokładnie naprzeciwko siebie i czy kropka na misce
przycisku zatrzymania
znajduje się dokładnie naprzeciw kropki na obudowie
zaczyna migotać w
silnika.W przypadku założenia blendera sprawdź, czy
kolorze czerwonym.
występ na misce blendera znajduje się dokładnie
naprzeciw nadruku na obudowie silnika. Z chwilą
prawidłowego założenia wszystkich akcesoriów
przestanie migotać czerwona lampka.
Essence
69
Advertisement
Table of Contents
