Toro Z MASTER Z100 series Setup Instructions
  1. Manuals
  2. Brands
  3. Toro Manuals
  4. Lawn Mower
  5. Z MASTER Z100 series
  6. Setup instructions
Toro Z MASTER Z100 series Setup Instructions

Toro Z MASTER Z100 series Setup Instructions

Hide thumbs Also See for Z MASTER Z100 series:
Table of Contents

Advertisement

Quick Links

Download this manual
Z100 Series Z Master Mowers

Loose Parts

Use steps 1 trough 12 in the following chart to verify all parts have been shipped and as a guide through the
setup.
Step
1
No parts needed
Roll bar, right section
Roll bar, left section
Roll bar, center section
Bolt, 3/8 x 1 inch
2
Curved washer, 3/8 inch
Flange nut, 3/8 inch
Bolt, 1/2 x 3-1/4 inches
Flange nut, 1/2 inch
Lanyard
3
Wheels
4
No parts needed
5
Seat
Nuts (installed on the seat)
Control lever–right
6
Control lever–left
Bolt, 3/8 x 1 inch
Curved washer, 3/8 inch
7
Bulk electrolyte with 1.265 specific gravity
(Purchase from a battery supply outlet.)
8
Air cleaner cap
Hose clamp
Number 2 general purpose lithium base or
9
molybdenum base grease. (Purchase
separately.)
10
No parts needed
2003—The Toro Company
8111 Lyndale Ave., Blomington, MN 55420, USA
Description
Printed in the USA
All Rights Reserved
Qty.
–
Raising the machine up
1
1
1
8
Installing the roll over protection system
8
(ROPS)
8
2
2
2
2
Installing the drive wheels
–
Checking the tire pressure
1
Installing the seat
4
1
1
Installing the motion control levers
4
4
80
Activating the battery
ounces
1
Installing the air cleaner cap
1
1 tube
Greasing the bearings
–
Preparing the side discharge chute
Register your product at www.Toro.com
Form No. 3329-965

Setup Instructions

Use
Original Instructions (EN)

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Z MASTER Z100 series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Toro Z MASTER Z100 series

Summary of Contents for Toro Z MASTER Z100 series

  • Page 1: Setup Instructions

    1 tube Greasing the bearings separately.) No parts needed – Preparing the side discharge chute 2003—The Toro Company Printed in the USA Original Instructions (EN) 8111 Lyndale Ave., Blomington, MN 55420, USA All Rights Reserved Register your product at www.Toro.com...
  • Page 2 Step Description Qty. No parts needed. – Checking the machine before delivery Operator’s Manual Engine Owner’s Manual Delivering the Machine to the Customer Parts Catalog Safety video Registration card Step Raising the Machine Up Parts needed for this step: None Procedure m–6919 1.

  • Page 3: Installing The Roll Over Protection System (Rops)

    Step Installing the Roll Over Protection System (ROPS) Parts needed for this step: Qty. Part Roll bar, right section Roll bar, left section Roll bar, center section Bolt, 3/8 x 1 inch Curved washer Flange nut, 3/8 inch Bolt, 1/2 x 3-1/4 inches m–6916 Flange nut, 1/2 inch Lanyard...

  • Page 4: Installing The Drive Wheels

    3. Lightly oil the ends 8. Tighten the front m–6891 of the center roll bar handles against the section. center roll bar ends. 4. Loosely install the center roll bar section, using 2 bolts (1/2 x 3-1/4 inches) and 2 flange nuts (1/2 inch). Note: Make sure the bolts are installed on the outside of the roll bar.

  • Page 5: Checking The Tire Pressure

    Step Step Checking the Tire Pressure Installing the Seat Parts needed for this step: Parts needed for this step: None None Procedure Procedure Check the air pressure 1. Remove the bolt in the front and rear and nut from the seat tires.

  • Page 6: Installing The Motion Control Levers

    Step Installing the Motion Control Levers Parts needed for this step: Qty. Part m–6867 Control lever–right Control lever–left Bolt, 3/8 x 1 inch (2 assembled) Curved washer, 3/8 inch (2 assembled) Procedure 1. Rotate the handles to the upright position. 2.

  • Page 7: Activating The Battery

    1. Remove the battery. Step Refer to the Operator’s Manual for instructions. Important: Do not add electrolyte while the battery is in the machine. You could spill it, causing corrosion. Activating the Battery Parts needed for this step: Qty. Part Bulk electrolyte with 1.265 specific gravity ounces (Purchase from a battery supply outlet.)

  • Page 8: Installing The Air Cleaner

    Warning 3. Install the hose clamp onto the air cleaner cap. Charging the battery produces gasses that can explode and cause serious injury. Keep cigarettes, sparks and flames away from the battery. m–6914 Make sure the ignition switch is off. Ventilate when charging or using the battery in an enclosed space.
  • Page 9 Step Step Checking the Spindles for Preparing the Side Grease Discharge Chute Parts needed for this step: Parts needed for this step: None Qty. Part 1 tube Number 2 general purpose lithium base or Procedure molybdenum base grease. (Purchase separately.) Remove the plastic tie holding the side discharge chute up and lower the chute into place.
  • Page 10 Step Checking the Machine Before Delivery to the Customer Parts needed for this step: None Procedure Before delivering the machine to the customer, ensure that you perform or have performed the procedures listed in the following table and initial each when finished. Refer to the Operator’s Manual for instructions on performing these procedures.
  • Page 11 Step Delivering the Machine to the Customer Parts needed for this step: Qty. Part Operator’s Manual Parts Catalog Engine Owner’s Manual Registration card Safety video Procedure At delivery, complete the items listed in the following table and initial each when finished. Model Number: Serial Number:...
  • Page 12 Describe the post sale service procedures for your store. Assist the customer in filling out and mailing the registration card or register online at www.Toro.com. Make sure that the customer receives the Operator’s Manual , Parts Catalog , and Engine Owner’s Manual, Set Up Instructions , and safety video.

Table of Contents