Input Specifications; Dc Input (Sink/Source) - Mitsubishi Electric MELSEC iQ-F FX5U User Manual

Programmable controller
Hide thumbs Also See for MELSEC iQ-F FX5U:
Table of Contents

Advertisement

2.3

Input Specifications

The CPU module input specifications are explained below.
24 V DC Input (sink/source)
The input points in the table below indicate the CPU module terminal points.
Item
No. of input points
FX5U-32M
FX5U-64M
FX5U-80M
Connection type
Input type
Input signal voltage
Input signal current
X0 to X17
X20 and subsequent
Input impedance
X0 to X17
X20 and subsequent
ON input sensitivity
X0 to X17
current
X20 and subsequent
OFF input sensitivity current
Input response
FX5U-32M
frequency
FX5U-64M,
FX5U-80M
FX5U-32M
FX5U-64M,
FX5U-80M
FX5U-64M,
FX5U-80M
Pulse waveform
Waveform
FX5U-32M
FX5U-64M,
FX5U-80M
FX5U-32M
FX5U-64M,
FX5U-80M
Input response time
FX5U-32M
(H/W filter delay)
FX5U-64M,
FX5U-80M
FX5U-32M
FX5U-64M,
FX5U-80M
FX5U-64M,
FX5U-80M
Input response time
(Digital filter setting value)
Input signal format
Input circuit insulation
Indication of input operation
Specifications
16 points
32 points
40 points
Removable terminal block (M3 screws)
Sink/source
24 V DC +20 %, -15%
5.3 mA/24 V DC
4.0 mA/24 V DC
4.3 k
5.6 k
3.5 mA or more
3.0 mA or more
1.5 mA or less
X0 to X5
200 kHz
When capturing pulses of a response frequency of 50 to 200 kHz, refer to Page 107 In the case
X0 to X7
of capturing high-speed pulses.
X6 to X17
10 kHz
X10 to X17
X20 and
0.10.05 kHz
subsequent
T1
T1 (pulse width)
2.5 s or more
X0 to X5
X0 to X7
50 s or more
X6 to X17
X10 to X17
ON: 2.5 s or less
X0 to X5
OFF: 2.5 s or less
X0 to X7
ON: 30 s or less
X6 to X17
OFF: 50 s or less
X10 to X17
ON: 50 s or less
X20 and
OFF: 150 s or less
subsequent
None, 10 s, 50 s, 0.1 ms, 0.2 ms, 0.4 ms, 0.6 ms, 1 ms, 5 ms, 10 ms (initial values), 20 ms, 70 ms
When using this product in an environment with much noise, set the digital filter.
No-voltage contact input
Sink: NPN open collector transistor
Source: PNP open collector transistor
Photo-coupler insulation
LED is lit when input is on
T1
T2 (rise/fall time)
1.25 s or less
25 s or less
2.3 Input Specifications
T2
T2
2 SPECIFICATIONS
23
2

Hide quick links:

Advertisement

Table of Contents
loading

This manual is also suitable for:

Melsec iq-f fx5u seriesMelsec iq-f fx5u-u-hw-e09r536

Table of Contents