Toshiba 4400 Series Installation And Operation Manual page 122

Installation Planning Guide for 15-80kVA UPS
Standard System: 208/120V Input, 208/120V Output
UPS kVA/ kW
Rating
15 kVA/ 13.5 kW 20.12 x 37.4 x 65.06
20 kVA/ 22.5 kW 20.12 x 37.4 x 65.06
25 kVA/ 22.5 kW 20.12 x 37.4 x 65.06
30 kVA/ 27 kW 20.12 x 37.4 x 65.06
50 kVA/ 45 kW 32.1 x 37.2 x 73.8
80 kVA/ 72 kW 32.1 x 37.2 x 73.6
Primary AC Input (208/120V 3-Phase / 4-Wire)
Maximum Input Power Demand
kVA PF Amps
15 >0.99 42 (46)
20 >0.99 55 (60)
25 >0.99 69 (74)
30 >0.99 83 (88)
50 >0.99 139 (148)
80 >0.99 222 (238)
Bypass AC Input (208/120V 3-Phase / 4-Wire)
Maximum Input Power Demand
kVA PF Amps
15 >0.99 42
20 >0.99 56
25 >0.99 69
30 >0.99 83
50 >0.99 139
80 >0.99 222
Battery Capacity Required Maximum Discharge
for Full Load Output at Full Load Output
kVA kWB
15 15
20 20
25 25
30 30
50 50
80 80
1 – External overcurrent overprotection not needed if battery cabinet(s) are each equipped with an appropriate internal circuit breaker
2 – External feeder cables may change depending on number of battery cabinets placed in parallel.
Rated Output Power
kVA PF Amps
15 0.9 42
20 0.9 56
25 0.9 69
30 0.9 83
50 0.9 139
80 0.9 222
112
Rev. 1.4
TOSHIBA
General Mechanical Information
Dimensions Weight
(W x D x H) Bare (w/ Int Batt.)
Inches Lbs.
725 (1015)
730 (1020)
750 (1035)
760 (1045)
965 (1920)
1550 (N/A)
Suggested External Suggested Minimum Feeder Wire Size
Feeder Breaker
Amps AWG or kcmil at 75º C Temp. Rating
60 (1) x 4 AWG / (1) x 2 AWG
80 A (1) x 3 AWG / (1) x 2 AWG
100 A (1) x 2 AWG / (1) x 2 AWG
110 A (1) x 2 AWG / (1) x 2 AWG
200 A (1) x 4/0 / (1) 250 kcmil
300 A (1) x 500 kcmil / (2) 500 kcmil
Suggested External Suggested Minimum Feeder Wire Size
Feeder Breaker
Amps AWG or kcmil at 75º C Temp. Rating
60 A (1) x 4 AWG / (1) x 2 AWG
80 A (1) x 3 AWG / (1) x 2 AWG
90 A (1) x 2 AWG / (1) x 2 AWG
110 A (1) x 2 AWG / (1) x 2 AWG
200 A (1) x 4/0 / (1) 250 kcmil
300 A (1) x 500 kcmil / (2) 500 kcmil
Battery Backup (288VDC Nominal)
Suggested External
Feeder Breaker
Amps DC Amps
65 A 70 A
87 A 90 A
109 A 110 A
130 A 150 A
217 A 225 A
347 A 350 A
AC Output (208/120V 3-Phase / 4-Wire)
Suggested External Suggested Minimum Feeder Wire Size
Feeder Breaker
Amps AWG or kcmil at 75º C Temp. Rating
60 A (1) x 4 AWG / (1) x 2 AWG
80 A (1) x 3 AWG / (1) x 2 AWG
90 A (1) x 2 AWG / (1) x 2 AWG
110 A (1) x 2 AWG / (1) x 2 AWG
200 A (1) x 4/0 / (1) 250 kcmil
300 A (1) x 500 kcmil / (2) 500 kcmil
4400 Series Installation and Operation Manual – 64527-006
Page 1 of 2
4400 UPS
Approximate Full- Mechanical Clearance for Ventilation
Load Heat Loss and Maintenance Access
kBtu/Hr
4.6 Top:
16 in
6.1
(406 mm)
7.6
9.1
15.2
24.3
Suggested Maximum Feeder Length
Per Phase / Neutral For Min. Wire Size in Steel Conduit
Suggested Maximum Feeder Length
Per Phase / Neutral For Min. Wire Size in Steel Conduit
Suggested Minimum Feeder
1
Wire Size Per Polarity
AWG or kcmil at 75º C Temp. Rating
6 AWG – 4 AWG
4 AWG – 3 AWG
2 AWG
2 AWG
4/0 – 250 kcmil
500 kcmil – (2) x 2/0
Suggested Maximum Feeder Length
Per Phase / Neutral For Min. Wire Size in Steel Conduit
4400-IPG-208/120v-208/120V
Front: Bottom/
36 in Sides/
(900 mm) Back:
0 in.
(0 mm)
Feet
380
380
380
380
380
380
Feet
380
380
380
380
380
380
Suggested Maximum
Feeder Length For Min. Wire
Size in Steel Conduit
Feet
70
70
70
70
70
70
Feet
380
380
380
380
380
380