ivanko IVK 5500 Owner's Manual
  1. Manuals
  2. Brands
  3. ivanko Manuals
  4. Home Gym
  5. IVK 5500
  6. Owner's manual

ivanko IVK 5500 Owner's Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
Safety Notice
Assembly Instruction
Resistance Chart
Warranty
Model
IVK 5500
Retain This
Manual for
Reference
10-1-04
OWNER'S
MANUAL
PERSONAL TRAINER
IMPEX FITNESS PRODUCTS
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: (800) 999-8899 Fax: (626) 961-9966
www.impex-fitness.com
info@impex-fitness.com
IVK 5500

Advertisement

Table of Contents
loading

Related Manuals for ivanko IVK 5500

Summary of Contents for ivanko IVK 5500

  • Page 1 NOTE: Please read all instructions carefully before using this product IVK 5500 Table of Contents PERSONAL TRAINER Safety Notice Hardware Pack Assembly Instruction Parts List Resistance Chart Warranty Ordering Parts Model IVK 5500 Retain This Manual for Reference 10-1-04 IMPEX FITNESS PRODUCTS OWNER'S 14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746...

  • Page 2: Table Of Contents

    WARRANTY....................…. ORDERING PARTS..................… BEFORE YOU BEGIN Thank you for selecting the IVANKO IVK-5500 PERSONAL TRAINER by IMPEX FITNESS PRODUCTS. For your safety and benefit, read this manual carefully before using the machine. As a manufacturer, we are committed to provide you complete customer satisfaction. If you have...

  • Page 3: Important Safety Notice

    IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1.
  • Page 4 WARNING LABELS PLACEMENT The Warning Labels shown here have been placed on Rear Base and Upper Frame. If the labels are missing or illegible, please call customer service at 1-800-999-8899 for replacement. Apply the label in the location shown.

  • Page 5: Hardware Pack

    HARDWARE PACK...
  • Page 6 HARDWARE PACK...
  • Page 7 HARDWARE PACK...
  • Page 8 HARDWARE PACK...

  • Page 9: Assembly Instructions

    ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches and five Allen Wrenches. NOTE: It is strongly recommended this machine be assembled by two or more people to avoid possible injury. STEP 1 (See Diagram 1) A.) Place the Main Base Frame (#2) on a flat surface. B.) Attach two Pulleys (#84) to the open oblique pulley brackets on the center of the Main Base Frame.
  • Page 10 STEP 2 (See Diagram 2) A.) Attach the Main Base Frame (#2) and the Rear Base (#18) to the bottom of the Rear Vertical Beam (#4). Align the holes and secure them together with two M10 x 3” Carriage Bolts (#105), Ø...
  • Page 11 STEP 3 (See Diagram 3) A.) Attach the Front Vertical Beam (#3) to the Main Base Frame (#2). Secure it with one M10 x 2 ¾” Allen Bolt (#104), two Ø ¾” Washers (#118), and one M10 Aircraft Nut (#125). Do not tighten the nut and bolt yet.
  • Page 12 STEP 4 (See Diagram 4) A.) Attach the Seat Support (#11) to the Front Vertical Beam (#3) and Main Base Frame (#2). Secure it to the Front Vertical Beam with one M10 x 2 ¾” Allen Bolt (#104), two Ø ¾” Washers (#118), and one M10 Aircraft Nut (#125).
  • Page 13 STEP 5 (See Diagram 5) A.) Place the Seat (#61) onto the Seat Incline Adjustment (#13). Secure it with two M10 x 1 ¾” Allen Bolts (#101) and Ø ¾” Washers (#118). B.) Insert the Seat Incline Adjustment into the opening on the Seat Support (#11). Use a Lock Knob (#71) to secure the Seat at desired height.
  • Page 14 STEP6 (See Diagram 6) A.) Slide the Sliding Pulley Frame (#21) onto the Sliding Pulley Vertical Beam (#9) from the bottom. Use a Lock Knob (#71) to secure the Frame at desired position. B.) Attach the Sliding Pulley Vertical Beam (#9) onto the Rear Base (#18). Secure it with two M10 x ¾”...
  • Page 15 STEP 7 (See Diagram 7) A.) Attach a Pulley to the front opening on the Upper Frame (#5). Secure it with one M10 x 2 ½” Allen Bolt (#103), two Ø ¾” Washers (#118), and one M10 Aircraft Nut (#125). Do not tighten the nut and bolt yet.
  • Page 16 STEP 8 (See Diagram 8) A.) Insert the Right Butterfly Arm (#6) into the pivot on the Front Vertical Beam (#3). Secure it with one M10 x ¾” Allen Bolt (#97), Ø ¾” Spring Washer (#115), and Ø 1 ½” x Ø ½” Washer (#122) from the bottom.
  • Page 17 STEP 9 (See Diagram 9) A.) Attach the Bench Press Base (#32) to the pivot on the Upper Frame (#5). Align the holes and insert a 8” Bench Press Axle (#44) through the holes. Secure the Axle with two M10 x ½” Socket Set Screws (#113).
  • Page 18 STEP 10 (See Diagram 10) A.) Attach the Backrest Adjustment Frame (#10) to the Front Vertical Beam (#3). Secure the bottom of the Frame to the Front Vertical Beam with one M10 x 3 1/8” Allen Bolt (#106), two Ø ¾”...
  • Page 19 STEP 11 (See Diagram 11) A.) Now move the machine to its final rest position. After installing the weight plates, the machine might be too heavy to move. B.) Align two Ø 2 ½” x 1” Rubber Bumpers (#76) onto the holes on the Main Base Frame (#2). Insert two Guide Rods (#15) through the Bumpers and into the Base Frame.
  • Page 20 STEP 12 (See Diagram 12) A.) Attach two Pulleys to each Angled Double Floating Pulley Bracket (#26). Secure each Pulley with one M10 x 1 ¾” Allen Bolt (#101), two ∅3/4” Washers (#118), and one M10 Aircraft Nut (#125). Do not tighten the nuts and bolts yet. The Pulleys may need to be removed when installing the Cables.
  • Page 21 STEP 13 Install the Upper Cable (See Diagram 13) A.) Attach the tip of the 161” Upper Cable (#52) to the Pulley (#84) on the front of the Upper Frame (#5). Insert the Cable into the Frame through the tube to the second opening. Remove the Pulley to get the Cable out then reinstall the Pulley.
  • Page 22 DIAGRAM 13...
  • Page 23 STEP 14 Install the High-Low Station Cable (See Diagram 14) A.) Insert the tip of the 262” High-Low Cable (#53) in between the pre-assembled two Small Pulleys (#85) on the Sliding Pulley Frame (#22). Note: You might need to remove one of the Pulleys in able to see the hole. B.) Draw the Cable through the Sliding Pulley Frame then pull upward to the Pulley on the top opening of the Sliding Pulley Vertical Beam (#9).
  • Page 24 DIAGRAM 14...
  • Page 25 STEP 15 Install the Lower & AB Cable (See Diagram 15) A.) Insert the 265” Lower Cable (#54) underneath the Pulley on the Leg Developer (#12). B.) Draw the Cable underneath the Pulley along the Main Base Frame (#2) to the Pulley under the Seat.
  • Page 26 DIAGRAM 15...
  • Page 27 STEP 16 Install the Butterfly Cable (See Diagram 16) A.) Attach one end of the 99” Butterfly Cable (#55) to a Cable Strap Bracket (#45). Place a Ø 7/8” x ½” Spacer (#80) in between the opening. Secure the Bracket to the Right Butterfly (#6) with a M10 x 1 5/8”...
  • Page 28 STEP 17 Install the Tension Cable (See Diagram 17) A.) Thread the bolt on the 161” Tension Cable (#56) into the Single Floating Pulley Bracket (#23) previously installed. B.) Draw the Cable down to the oblique Pulley on the Main Base Frame. Draw the Cable underneath the Pulley then pull upward to the lower Pulley on the Angled Double Floating Pulley Bracket (#26) previously installed.
  • Page 29 STEP 18 (See Diagram 18) A.) Attach two Weight Plate Covers (#16) to the Top Socket Assembly (#20) and Main Base Frame (#2). Secure each Weight Plate Cover with four M6 x 3/8” Allen Bolts (#95) and Ø ¾” Nylon Washers (# 67). DIAGRAM 18...

  • Page 31: Parts List

    PARTS LIST 161” Tension Cable KEY NO. DESCRIPTION Q’ty Ankle Strap Bench Press Arm AB Strap Main Base Frame Triceps Rope Front Vertical Beam Backrest Board Rear Vertical Beam Seat Upper Frame Foam Roll Right Butterfly Butterfly Handle Bushing Left Butterfly Weight Plate Bushing Butterfly Swivel Handle Selector Stem Bushing...
  • Page 32 M6 x ¼” Socket Set Screw M6 x 3/8” Socket Set Screw M10 x ½” Socket Set Screw M10 x ¾” Socket Set Screw Ø ¾” Spring Washer Ø 1” Spring Washer Ø ½” Washer Ø ¾” Washer Ø 7/8” Bent Washer Ø...

  • Page 33: Resistance Chart

    IVK-5500 WEIGHT RESISTANCE CHART WEIGHT PLATE Station Arm Curl Lat Pull AB Station Leg Developer Bench Press Butterfly High Low Cable WEIGHT PLATE Station Arm Curl Lat Pull 117 128 AB Station Leg Developer Bench Press Butterfly High Low Cable * Numbers are approximate.

  • Page 34: Limited Warranty

    IVANKO By IMPEX FITNESS PRODUCTS LIMITED WARRANTY IMPEX Inc. ("IMPEX") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase.

Table of Contents