Onkyo TX-SR502 Instruction Manual page 44

TX-SR502_En.book Page 44 Friday, March 12, 2004 1:05 PM
Using the Listening Modes —Continued
Dolby Digital/DTS setting
(5.1 or 6.1-channel playback)
If the Surr Back setting is set to anything other than None
in the Speaker Configuration (page 32), and if the sur-
round information in the current input signal is " 3/2.1 "
or " 3/3.1 (you can check the format of a digital input sig-
nal on page 35, "Displaying Source Information."), you
can determine whether Dolby Digital and DTS material
is played using 6.1-channels or 5.1-channels.
ON
V1
1
DVD
4
CD
7
+10
--/---
TONE
DVD
TV
DIMMER
TV
INPUT
ENTER +
CH
DISC
-
PREV
CH
DISPLAY
REC
AUDIO
SURR
SURR
REPEAT
TEST TONE
OPEN/CLOSE
1
Press the [AMP] mode button fol-
lowed by the [SETUP] button.
AMP
2
Use the Up and Down [ ]/[ ]
buttons to select "4. Audio
Adjust," and then press the
ENTER
[ENTER] button.
ENTER
44
STANDBY
T V
I INPUT
V2 V3
2 3 +
MULTI CH TV CH
-
5 6
TAPE TUNER
8 9
T V VOL
0 CLEAR
TUNER/
TAPE
AMP
_
+
AMP
REMOTE MODE
CD MD CDR
VCR CABLE SAT
SLEEP
ENTER VOL
SETUP
MUTING
SP A SP B RANDOM
SUBTITLE ANGLE LAST M
ALL ST STEREO
A-B SEARCH MEMORY
DIRECT DSP DSP
- - + +
CH SEL LEVEL LEVEL LEVEL LEVEL
VIDEO OFF
L NIGHT CINE FLTR
RC-567M
3
When playing Dolby Digital
material:
Use the Up and Down [ ]/[ ]
ENTER
buttons to select "SB (Dolby D),"
and then use the Left and Right
[ ]/[ ] buttons to select "Auto,"
"On," or "Off."
When playing DTS material:
ENTER
Use the Up and Down [ ]/[ ]
buttons to select "SB (DTS)," and
then use the Left and Right [
[ ] buttons to select "Auto,"
"On" or "Off."
4
Press the [SETUP] button.
Setup closes.
5
Use the remote controller's
[SURR] button, or the AV
SURR
Receiver's LISTENING MODE
[ ]/[ ] buttons to select the
required listening mode.
Dolby Digital Setting
Auto: If the source signal contains a Dolby Digital
EX flag, Dolby Digital EX 6.1 is used. If not,
Dolby Digital 5.1 is used.
On: Dolby Digital EX 6.1 is used regardless of
whether the source signal contains a Dolby
Digital EX flag. You can switch between Dolby
Digital EX and PL IIx Music.
Off: Dolby Digital 5.1 is used even if a Dolby Dig-
ital EX flag is present.
DTS Setting
Auto: If the source signal contains a DTS-ES flag,
DTS-ES Discrete (6.1) or DTS-ES Matrix
(6.1) is selected automatically. If not, DTS 5.1
is used.
On: DTS-ES 6.1 is used regardless of whether the
source signal contains a DTS-ES flag. If the
source signal contains a DTS-ES flag, DTS-ES
Discrete (6.1) or DTS-ES Matrix (6.1) is
selected automatically. If the source signal
does not contain a DTS-ES flag, you can select
DTS+Dolby EX, PL IIx Music, or
DTS+Neo:6.
Off: DTS 5.1 is used for all DTS sources, even if a
DTS-ES flag is present.
]/