Turning On; First Time Setup - Onkyo TX-SR502 Instruction Manual

TX-SR502_En.book Page 31 Friday, March 12, 2004 1:05 PM

Turning On

• American • Other
model models
STANDBY/ON STANDBY/ON
STANDBY/ON STANDBY/ON
POWER
ON OFF
A SPEAKERS B A SPEAKERS B
PHONES PHONES
POWER
Turning On the AV Receiver
1 Set the [POWER] switch to the
ON position ( ). (Skip this step if
POWER
you have American model.)
ON OFF
The AV Receiver enters Standby mode,
and the STANDBY indicator comes on.
Note:
• The remote controller has no effect
while the [POWER] switch in the
OFF position.
2
Press the [STANDBY/ON] button.
Alternatively, press the remote
STANDBY/ON
controller's [AMP] button fol-
lowed by the [ON] button.
The AV Receiver comes on, the display
lights up, and the STANDBY indicator
Remote
goes off.
controller
ON
To turn off the AV Receiver, press the
[STANDBY/ON] button. The AV
Receiver will enter Standby mode. To
prevent any loud surprises the next time
STANDBY
you turn on your AV Receiver, always
turn down the volume before turning it
off.
Notes: (not for the American model)
• The AV Receiver is shipped with the POWER switch
in the ON position ( ). When the power cord is con-
nected for the very first time, the AV Receiver will
enter Standby and the STANDBY indicator will light
up.
• To completely shutdown the AV Receiver, set the
POWER switch to the OFF position ( ).

First Time Setup

ON
STANDBY
STANDBY/ON
ON STANDBY
T V A SPEAKERS B
I INPUT
V1 V2 V3 PHONES
+
1 2 3
DVD MULTI CH TV CH
4 5 6 -
CD TAPE TUNER
7 8 9
T V VOL
+10
0 CLEAR
--/---
TUNER/
TONE
TAPE
_
+
AMP
REMOTE MODE
Assigning the Digital Inputs to Input
Sources
To enjoy Dolby Digital and DTS, you must connect your
DVD player to the AV Receiver by using a digital audio
connection (coaxial or optical).
With this function you can assign digital audio inputs to
input sources. You only need to change these assign-
ments if your connections don't match the default
assignments listed below.
Input source
DVD
VIDEO 1
VIDEO 2
VIDEO 3
TAPE
CD
For example, if you connect your DVD player to the
COAXIAL DIGITAL IN, you'll need to change the
DVD input source from OPT 1 to COAX, and change the
CD input source to something other than COAX.
If you want to use the TAPE input source with only the
analog TAPE IN sockets, you'll need to change the
TAPE assignment from "OPT3" to "----" (Analog).
You can change the assignments as follows.
1
DVD VIDEO 1
VCR
VIDEO 2 VIDEO 3
TAPE
2
DIGITAL INPUT
3
DIGITAL INPUT
DIGITAL INPUT
TUNING
PRESET
ENTER
STANDBY
SETUP RETURN
LISTENING
TONE STEREO MODE DISPLAY DIGITAL INPUT MEMORY TUNING MODE
CLEAR
MULTI CH DVD VIDEO 1 VIDEO 2 VIDEO 3 TAPE TUNER C D
VCR
Input selector buttons
DIGITAL INPUT
OPT1 (OPTICAL 1)
- - - - (Analog)
OPT2 (OPTICAL 2)
- - - - (Analog)
OPT3 (OPTICAL 3)
COAX (COAXIAL)
Press the input selector button
for the source that you want to
assign.
(Digital inputs cannot be assigned to
the TUNER input source.)
C D
Press the [DIGITAL INPUT]
button.
The current assignment appears.
Press the [DIGITAL INPUT] but-
ton repeatedly to select COAX,
OPT1, OPT2, OPT3, or – – – –.
MASTER VOLUME
VIDEO 3 INPUT
S VIDEO VIDEO L AUDIO R
31